Laserfiche WebLink
Cond'olTech TR M.73 <br /> Ta* `' ' COROBONDTM 100 <br /> CAMAtM <br /> Contahnem 8r <br /> Cada, anal EPDXY PRIMER/SEALER <br /> • PART A B58W5100 OFF WHrrE <br /> i cogs S PART A B58AS100 HAZE GRAY <br /> PART B B58V5100 HARDENER <br /> PRODUCT INFORMATION Revised 5/05 <br /> P'fIQp11CT"`�ESCFtIPTION I �COAAMfinDE.D USES <br /> COROBOND 100 EPDXY PRIMER/SEALER is a high solids, Corobond 100 can be used on all bare concrete surfaces <br /> low VOC, tow viscosity, penetrating epoxy primer/sealer for- where a 2 part eppxy, penetrating primer is recommended. <br /> mulated specifically for use over concrete surfaces in sec- Its low viscosity and quick recoat time allow it to be used for <br /> ondary containment environments. areas that need a fast turnaround. <br /> • Helps prevent "blow-back" and "outgassing" <br /> • Low viscosity • Secondary Containment <br /> • Low VOC <br /> • Fast dry • Designed specifically as a high performance primer sealer <br /> • Superior penetrating characteristics for secondary containment applications. <br /> • Improved visibility during application <br /> PRODUCT CH1 _ 105--CS Edi Af,0� CHARACTE 11rTICs <br /> Finish: Flat sheen A high performance primer/sealer for new or existing bare con- <br /> crete surfaces <br /> Color: Off White,Haze Gray <br /> Volume Solids: 98%, mixed Helps prevent"blow-back"and'outgassing"of topcoats supe- <br /> rior penetrating characteristics <br /> VOC(calculated): <25 g/I; 0.2 Ib/gal, mixed <br /> Superior penetrating.characteristics <br /> Mix Ratio: 2:1 by volume, premeasured <br /> Refer to applicable topcoat for additional performance <br /> Recommended Spreading Rate per coat: information <br /> Wet mils: 4.0-6.0 <br /> Dry mils: 4.0-6.0 White in color to provide contrast with concrete <br /> Coverage: 265 - 400 sq ft/gal approximate <br /> Apply primer to achieve uniform hiding,appearance,and com- Excellent penetrating properties to provide a"tight and sound" <br /> plete wetting of the concrete surface, approximately 4.0 - 6.0 substrate prior to subsequent topcoats <br /> mils wft. Coating will be partially absorbed into the concrete. <br /> Roll out any puddles. <br /> Can recoat while primer is still tacky <br /> Drying Schedule: @ 5.0 mils wet,77°F and 50%RH: <br /> To touch: 2 hours Designed to be topcoated <br /> To recoat: <br /> minimum: 3 hours <br /> maximum: 24 hours' <br /> To cure: 7 days <br /> "Can betopcoated up to 30days afterapplication with eitherMacropoxy646 <br /> orSbN-Seam VSE(interimexposureonly). <br /> Primercan betopcoated even Ifthe surface isstilI tacky. <br /> Ifmaximum reooettimeisexceeded,abradesurface beforerecoating. <br /> Drying timeistemperature,humidity,and film thickness dependent. <br /> Pot Life: 45 minutes ® 77°F <br /> Sweat-in Time: None required <br /> Shelf Life: 18 months, unopened <br /> Store indoors at 40°F to 100°F. <br /> Flash Point: 100°F PMCC, mixed <br /> Reduction: Not recommended <br /> Clean Up: Xylol, R2K4 <br /> ControlTech TRM.73 continued on back <br />