Laserfiche WebLink
Gwtro[Tech TR M.73 <br /> Tam COROBONDTM 100 <br /> Cantaivnem& <br /> c« osim EPDXY PRIMER/SEALER <br /> PART A B58W5100 OFF WHITE <br /> ' COafings PART A B58A5100 HAZE GRAY <br /> PART B BSBV5100 HARDENER <br /> PRODUCT INFORMATION <br /> �carMfQo $YSTgAS - ltF[ 10E PREPARATION <br /> Concrete, Secondary Containment: Surface must be clean, dry, and in sound condition. Remove <br /> Concrete& Masonry: all oil, dust,grease,dirt,loose rust,and other foreign material <br /> 1 ct. Corobond 100 Epoxy Primer/Sealer to ensure good adhesion. <br /> Apply primer to achieve uniform hiding, appear- <br /> ance, and complete wetting of the concrete surface, Refer to product Application Bulletin for detailed surface prepa- <br /> approximately 4.0- 6.0 mils dft. Coating will be ration information. <br /> partially absorbed into the concrete. Roll out any Minimum recommended surface preparation: <br /> puddles. Concrete&Masonry: SSPC-SP13/NACE 6, or <br /> 1-2 cts. Kern Cati-Coat HS Epoxy Filler/Sealer ICRI 03732,CSP 3-6' <br /> @ 10.0- 20.0 mils dft/ct, as required to fill voids *Refer to System Selection Guide <br /> and bugholes to provide a continuous substrate. <br /> 1-2 cts. Cor-Cote E.N. 7000 Epoxy Novolac Coating TINP*. <br /> @ 10.0- 14.0 mils dft/ct' Do not tint. <br /> ' Dependent on the severity of the environment,other accept- 4RP�.i gTtCyN fJND0*s , <br /> able topcoats may include Cor-Cote HCR FF, Phenicon HS, <br /> or Shelcote II. Temperature: 55°F minimum, 100°F maximum <br /> (air, surface, and material) <br /> At least 5'F above dew point <br /> Mortar System: <br /> 1 ct. Corobond 100 Epoxy Primer/Sealer Relative humidity: 85% maximum <br /> @ 4.0-6.0 mils dft Refer to product Application Bulletin for detailed application <br /> 1 ct. Cor-Cote HCR Epoxy with 70 lbs Type T Aggregate information. <br /> per 1.25 gallons @ 3/160 dft yields 44 sq. it. <br /> 1 ct. Cor-Cote HCR Epoxy @ 15.0-20.0 mils dft Q�ttiItNG �NFORMAT�QN <br /> 1 ct. Cor-Cote HCR FF Flake Filled Epoxy Packaging: <br /> @ 15.0-20.0 mils dft g 9 <br /> 3 gallon mix Part A-2 gallons <br /> Part B- 1 gallon <br /> 15 gallon mix Part A-two 5 gallon containers <br /> Part B - one 5 gallon container <br /> Weight per gallon: 9.5 f 0.2 Ib, mixed <br /> SAFETY PRECALMONS <br /> Refer to the MSDS sheet before use. <br /> The systems listed above are representative of the product's Published technical data and instructions are subject to <br /> use. Other systems may be appropriate. change without notice. Contact your Sherwin-Williams repre- <br /> sentative for additional technical data and instructions. <br /> DISOLAIIMER WA�FbgNTlf <br /> The information and recommendations set forth in this Product Data Sheet are The Sherwin-Williams Company warrants our products to be free of manufactur- <br /> ing <br /> detects in accord with applicable Sherwin-Williams quality control procedures. <br /> based upon tests conducted by or on behalf of The Sherwin-Williams Company. Liability <br /> Such Information and recommendations set forth herein are subject to change dfefor products proven defective, If any, is limited to replacement of the <br /> and pertain to the product offered at the time of publication. Consult your defective product or the refund of the purchase price paid for the defective <br /> product as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUAR- <br /> Sherwin-Williams representative to obtain the most recent Product Data Infor- ANTEE OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR <br /> mation and Application Bulletin, IMPLIED,STATUTORY,BY OPERATION OF LAW OR OTHERWISE,INCLUD- <br /> ING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. <br />