INSTALL_2020 - Laserfiche WebLink

Home Browse Search

UL/ ULC ® Piping SPECIFICATION Primary Piping SECTION 1 - Scope This section covers the use of fiberglass reinforced plastic 2 . 06 Acceptable Manufacturers - NOV Fiber Glass (FRP) pipe for single wall fuel handling and fuel handling vent Systems , 501 -568-4010 , or approved equal . and vapor applications Including gasoline , unleaded gasoline , gasoline/alcohol mixtures , blo -diesel , DEF and diesel up to Section 3 - Material and Construction 150°F and 250 psig cyclic pressure , 3 . 01 2 " - 4 " Pipe - The pipe shall be manufactured by the filament winding process using an amine cured epoxy SECTION 2 - General Conditions thermosetting resin to Impregnate strands of continuous 2 .01 Coordination - Material furnished and work glass filaments , which are wound around a mandrel at a performed under this section shall be coordinated with the 543/4" winding angle under controlled tension . The pipe related work and equipment specified under other sections, shall be heat cured and the cure shall be confirmed using a Le . Valves, Flexible Connectors , Equipment , Differential Scanning Calorimeter, Pipe shall be supplied with a T. A . B . "' (Threaded and 2 . 02 Governing Standards - Except as modified or Bonded) ends . supplemented herein , all materials and construction methods Pipe shall have a minimum continuous cyclic pressure shall comply with and be tested in accordance with the rating of 125 psig at 150°F In accordance with ASTM D2992 , following standards and test methods : Procedure A or UL 971 pressure rating . Standards and Test Methods : All pipe shall be 100% hydrotested at the factory before shipment at a minimum pressure of 265 psig and shall be UL971 Standard for Nonmetallic Underground Piping for Flam - UL971 -2004 Listed and labeled . 2004 mable Liquids 3 . 02 ASTM D2310 Classifications (at 73 . 40F) ASTM Standard Classification for MachineWade " Fiberglass" 2" - all RTRP- 1 1 AF D2310 ( Glass Fiber Reinforced Thermosetting Resin ) Pipe ASTM Standard practice for obtaining Hydrostatic or Pressure 4" RTRP- 11 AH D2992 Design Basis for " Fiberglass" (Glass Fiber Reinforced ( Mechanical properties cell classifications shown are Thermosetting Resin ) Pipe and Fittings minimums .) 3 . 03 Fittings - All fittings shall be manufactured using 2 . 03 Operating Conditions - In addition to the above the same type of material as the pipe , Fittings may be listed minimum design requirements, the system shall meet manufactured either by compression molding , filament the following minimum operating conditions : winding , resin transfer molding or contact molding methods . All fittings , adapter, and sump penetrations shall be UL971 - a. Operating Pressure 2004 Listed . b . Fluid Conveyed Fittings shall be adhesive bonded matched tapered bell c . Test Pressure and spigot . 3 . 04 Connections - Connections to flex connectors or 2 . 04 Quality Assurance - Pipe manufacturer' s quality other piping materials shall be made by the use of NPT program shall be In compliance with ISO 9001 and/or API Q1 . (National Pipe Thread) threaded adapters or flanges bonded to the FRP piping system , 2 .05 Delivery. Storage . and Handling - Pipe and fittings 3 . 05 Sump Penetrations - Sump penetrations shall be shall be protected from damage due to Impact and point made by means of a permanently bonded FRP coupling . The loading . Pipe shall be properly supported to avoid damage coupling shall be capable of adjusting for the slope of the due to flexural strain . The contractor shall not allow dirt , piping system entering or exiting the sump wall , debris or other extraneous materials to get Into pipe and 3 .06 Adhesives - Adhesives shall be manufacturer' s fittings . All factory machined areas shall be protected from standard for the piping system specified . sunlight until Installed , v~w. f9splipe . com fgspipe@ncv. c® rn KW Fiber Glass Systems