COMPLIANCE INFO_2021 - Laserfiche WebLink

Home Browse Search

kill Recommended Instructions CATLOW Installation, Maintenance, Inspection CATLOW CTMCA Breakawa 577014-071y DATEE 0 03/2 1 3/2016 VERY IMPORTANT READ THIS BEFORE INSTALLING YOUR BREAKAWAY WARNING: USE ONLY ON SYSTEMS RATED AT 50 PSI MAXIMUM USE ON SYSTEMS HAVING HIGHER STATIC PRESSURE MAY CAUSE PEMATURE SEPARATION ALWAYS CHECK FOR ELECTRICAL CONTINUITY FOLLO WING PETROLEUM EQUIPMENT INSTITUTE (PEI)RECOMMENDED TEST PROCEDURE(PEIIRP400-02) PRIOR TO INSTALLATION:Refer to the model of breakaway for the maximum pull force before you proceed with the instructions Caution must be used when testing to prevent damage to the dispenser or personal injury. ALL DISPENSERS MUST BE BOLTED TO THE ISLAND. (NFPA 30A 6.3.4 and PEIIRP500-11 2.2) CONFIRM DISPENSER IS SECURE. -Attach a spring scale to the dispenser where the breakaway will be installed. 2 -Apply a 350 lbs pull force at various angles and check the emergency valves, 6 5 Dispenser and hose assembly. (UL STANDARD 567) -Release the load and complete the installation of the breakaway. DISPENSER 1 TOP VIEW CTMCA INSTALLATION HIT-P/N 4037 Qty. P/N Description 4 1 ea. CTMCA Cam Twist Magnetic Breakaway 3 2 ea. M3418 CTMCA Hose Adapter • • -The CATLOW in-line breakaway must always be installed between two hose sections(example: whip&main hose) -On side hose connections install the breakaway between the nozzle and the hose retractor(NFPA 30A 6.5.3) DO NOT INSTALL THE BREAKAWAY ON THE DISPENSER SIDE OF THE HOSE RETRACTOR -On an overhead hose connection,install the short section of whip hose then the breakaway,hose and nozzle INSTALLATION INSTRUCTIONS FOR THE CTMCA BREAKAWAY NOTE: Catlow recommends using a swivel end hose in proximity to the CAM TWIST 1. Isolate/turn the dispenser OFF and relieve the line pressure from the system by opening the nozzle and allowing the system to drain into an approved metal container. 2 Observe the flow direction arrow on the breakaway and install with the flow arrows pointing toward the nozzle. 3. Use thread sealant recommended by UL for petroleum products on pipe thread connections. 4 Use oil or grease on straight or metric thread o-ring fittings-DO NOT USE TEFLON TAPE. 5. When replacing the CTMCAs with M3418 adapters on both ends,there are special precautions that must be observed.When replacing ACCTMCA,ensure the M3418 ferrule stays with each hose and does not get discarded along with the discarded CTMCA. Whip Hose Ferrule M3418 Adapter M3418Adapter Ferrule Nozzle Hose Breakaway Cover 4736 6. Re-attach the hose to the M3418 adapter and tighten to 50 ft-lbs torque.CAUTION:Torque adjacent parts only(e.g.,hose and adapter to which it connects). Slide plastic cover 4736 over the breakway as far as it will go(for retrofit instructions see page 2). 7. Activate/turn the dispenser ON and purge the hoses and nozzles of air into an approved metal container. 8. Check the system for leaks,replace any item that exhibits signs of leakage. UseOnlyULListed Hoses should not belong enough thata vehicle could Always ReferToYour Paste Type Thread drive overthe hose resulting in a direct pull on the It/ Local City,State Or Federal Sealant retractor cable or dispenser and bypass the breakaway Testing Regulations PAGE 1 OF 4 2750 US RT 40 WWW.CATLOW.COM TIPP CITY,OHIO 45371 USA Phone(800)222-8569 Fax(937) 898-8631 ©2016 veeder-Root LLC. All Rights Reserved.