SR0081922 - Laserfiche WebLink

Home Browse Search

VrnUuV waftir ON-and W-Sedes Tank W6starr � August 2016 _ C®�i f(tl�c�ftuc�r� �inlJ�C�l21rNC�� Dammam U B rFB L41R6�Y®ra' 10.Spread exeea l aealanl In ma Imeder " TuV•'Titea Corporation Riser tanks Joint behveen the tank and riser with a 'I.Install riser assembly prior to backfMIng tank. - - small putty Brite or manually. :•i _ 2.Align TW-Tole adapter ring over Infiltrator connector ring and mark 10 ®elute You begin IlghteNng the screws and stripping the receiving holes.Be sure to Insert 11.Connect additional TW Riser sections - evenly spaced pilot hole locations so that they match up to mceMng This document provides recommended procedures for the connection screws In a"star"pattern,tightening opposite skies of the riser or pipe or the Included Infiltrator IM as needed. holes on the Infiltrator connector Ong. of commercially available riser products to Infiltrator Water adapter. 12.Backfin tank h accordance with >,. 3.Drill new pilot holes Into Tuf-Tlte adapter Ong. Technologies'(In111hator's)IM-Sadao tanks. Note:Use 014 1%-loch stainless steel scrotvs unless otherwise noted Infiilmtors tank Instaliallen Inslnicllons. ,i0 4.Apply 2 continuous 3/8"beads of ISI 1500 Adhesive Sealant In The Intent of tfils document Is to provide procedures for making the alignment with the factory-drilled 11.In addition to the measures shown In this document,additional sealant 13.Following lank bacMllling,visually examine the riser to Inflltralor connection between the user sod lank.Once Inti connection hes been screw holes on tits lop surface may also be applied to the exterior IoIM connection to help establish and connector ring Joint for damage resultlrg tram bpckltll placement. =v made,the riser manufacturers standard Installation Instructions should he maintain watertight connections. Repn!r or replace if damaged.Allow a minimum sealant cure time of 24 of the Infiltrator connector Ong. ' used to complete the assembly. The sealant thickness must be hours below testing or placing Into service. The to fill the gap beneath Risers mull be Installed according to stale and/or local regulations,which supersede the gukfellcm In this document.It unsure of the requirements for Compatible Products Uset by Infiltrator Riser the Tut-The adapter Ong. a particular site,contact the local health department or permitting authority. The Infiltrator IM-Series tanks are rnmpatible With 24-Inch(000-mm) 1.Install riser assembly prior to backfIling tank. 6.Inert Tuf=1110 adapter ring 4 diameter user products from the following manufacturers: 2.Align EZset Poser Section over _ - end center over the Intglrator Parts and Supplies •Infiltrator TW Riser •Hart by Infiltrator Infiltrator connector Ong and mark 10 connector ung. The parts and supplies necessary for Installation of a riser system on •Tuf-Tito°Corporation •Polylok'"'Inc. ovenly spaced pilot hole locations so 6.Verify that the ISI 1500 Adhesive Seelnnl remains properly aligned on Infiltrator IM-and 1W-Seues tanks must ion purchased separately from the that they match up to recaving holes on tlo Tut-Tile adapter ring. tank.NI parts and supplies are commercially nvallablo.Contact Infiltrator The following 244ch(800-mm)diameter pipe products are also compatible the Innitralor connector rig. ?i 7.Align Ilio 10 drilled.pilot holes on the Tuf-Tile adapter Ong with the 10 or Ilia riser manufacturer for assistance obtaining pads and supplies. vuth the Infiltrator IMSedes tanks: receiving hulas on the Infiltrator 3.DOII 70 now pilo!holes Into - `<',t, •IPEX Ultra-Rlb-PVC pipe Ha0t Riser Sectlen, 2 connector ring. ° Required Tools •Corrugated high density polyethylene(ilDPL)pipe 4.Apply 2 continuous 3/8"beads oft_4 - &Fasten the Tuf-Tile adaptor ring •Screw gun •Extended drill driver bit(0-12",150-300 mm)optional to the Infiltrator connector ung '« ISI 1500 Adhesive Sealant In alignment '`' •Rag gun •Marker a marking panel •Brush with tan ews x i V.-Inch stainless " 1+'•;5 Rag •Utility knife •Latex gloves infiltrator TW Riser with the factory-drilled screw holes steel screws. �b:}�_ ' •#14 x 1y stainless steel screws(supplied with Infiltrator TW Risers) 1.Install riser assembly prior to backfilling tank. on the lop surface of Ilia Infiltrator t s > connector Ong.The sealant thickness 9.Tighten smetvs In a'slar`212 x 9/4 stainless steel screvrs(for IFEX) 2.Place the TW Riser over the Infiltrator connector Ong and totals must be adequate to fill the gap pattern,tightening screws onthe TW Riser to the proper alignment.Proper alignment Is er ll beneath the EZsel Riser Secllon. opposite skies of the Tuf-Tllo adaptor Ong.Repeal the star pattern at General Guidelines fa the IMSedes tanks vdian Ilia recalvn l slots on the bottom of the riserleast hvice,without over tightening screws.Compress the ISI 1500 1.Complete riser assembly Installation,Including Installation of adapter engage the Indexing labs on the Infiltrator connector Ong. 5.Invert EZmO Riser Section and center over the InfI trator connector Ong. Adhesive Sealant to lank evenly during fastening. ring,rlem(s),and Ind prior to backglling lank. 3.Owe proper alignment has been - 8.Verify that the ISI 1500 Adhesive Sealant remains property aligned on 10-Connect the Turf-rite riser to the Tuf-Tlte adapter ring and Install lids Ilia EZset freer Section. Ngte:Risers are to be connected to Infiltrators access part connecter achieved,mark the riser and lank to Identify v - according to Tuf•Ttte's hulmctlons. ring(referred to herein as'Infiltrator connector ring'?.The Infiltrator comeact alignment orientation. ;=.. 7.Align the 10 dined pilot holes on the Heat Riser Section wlth the 10 Nota The Infiltrator tank ltd pmvldas a avatortight seal with copriector ring/s a permanent component of the tank body,and is the q Apply 2 continuous 3/8'beads of ISI �' '%` receiving holes on the Infiltrator connector ring. the TuFTits riser and maybe used, connection poinLlor the riser component. 1500 Adhesive Sealant In alignment vdih Note:To speed up the process of fastening the screws,Infiltrator Water 11.Backllll tank in accordance with Infiltratof's tank installation 2.Ensure that all connection surfaces are clean and dry. the factory-drilled screw holes In then`•'.C Technologies recommends the%as of an extended drill driver bit(6-42", Instructions. ' 3.Sealant shell be ISI 1500 Adhesive Sealant or equivalent. channel on the top surface of the Infiltrate i-_3 ,•,MS�s��` 150-300 mm). V.Fdbwkg lank backfilling,visually examine the riser to Inhlireler 4.Sealants vary between manufacturers.Sealant Identified herein connector Ong.The sealant thickness must 8.Fasten(he FZset Riser Section to --- connector ring Joint for damage resulting from backfill placement.Repair represents a minimum recommendation.The Installer must use discretion In be adequate to fill the gap beneath the TW fuser. Ills Infiltrator connector ring i•Ath ten or replace If damaged.Allow a minimum sealant cure time of 24 hours determining the size and amount of sealant needed to craft and maintain a - 1 #14 x i%-Inch stainless steel screws. before testing or placing into service. watertight seal. (I.Tighten screws In a'star"pattern, POIyLOk^'Inc.Riser 5.Keep soalnnl at a temperature,fill toast 60'E/18°C)that maintains r':; tightening screws on opposite sides - - Note:Polylok riser must be Installed using Infiltrator Pipe Adapter Its worklibility.Keep It free from did end debris that may compromise a lr of the EZset Riser Section,Repeat the - Ring. watertight seal. _ yy star pattern at least twice,vdthout over e .0.When applying sealant to a part,ensure continuous appllcallon to avoid t - 1.Install riser assembly prior to backfYMg tank r„ tlghleNrg screws.Compress the ISI gaps that may cause looks.Apply an adequafo quantity to ensure a sealedqa - - 1500 Adhesive Sealant to tank evenly during fastening. 2.Align the 10 pilot holes on the minectlon. - - Polylok Riser-to-Riser Adapter 10.Spread the excess sealant Into the ✓ 7.Physically spread the sealant Into the charms:on the Infiltrator Ring with the 10 receMng holes on 5.Invert the TW Riser and center over the Infiltrator connector d htedor Joint between the tank and riser -.I connector Ong to ensure that It distributes properly dudng assembly. �. the infiltrator connector ung end 8.The ISI 7500 Adhesive Sealant r ulnas 24 hours for in the proper alignment poslllon dolomdned in step 3. with a small pully knife or manually. _ ,y11 s-q mark both locos to identify proper ey proper curl Ensure there Is even coverage an both p ly P p = 8.Vert that the sealant remains roe all _ riot to use w testing.Determine curio limes for other sealants based ty property rN 9ned on TW gleet. `� �} alignment. P 9• 9surfaces. - on manufacturers recommendations. 7.The 10 holes on the riser should be eilgned w•10a ihe10 receiving holes 3.Apply 2 continuous 3/0'beads 9.Ensure that all screws supplied%Atli riser products are Installed for on the Infiltrator lank connoclor ring. 11.Connect additional F7-aet deer a, 01151 1500 Adhesive Sealant In t Psections or EZsel Yd as needed. ^ - connection of adapter rings,risers,and lids.insert screwe only In proscribed - alignment with the factory-driNed S.Fasten line Tyr fiber 1p the lenllfalM CenlleCfen 16 Inratlons. Int Note:to not use the supplied screw lidos r t Ins lop surface of �( - drg%vtth 101actory-supplied acrewe.]fine factory- Infiltrator tank ltd,as/t does not provide a IveleAl ht seal with the Note:To speed up the process of fastening the supplied screws are not available,use ten 414 x P g Polylok Hisor-to-Hlser Adaptor scrmvs Infiltralor recommends the use of an IA-Inch stainless steel screws. EZset riser.Instead,use Fleet lid with the EZset riser. Ring.Sealant thickness must(III ice, extended drill driver bit(6-12",150-300 mm). 13.Backfill tank In accrd oance with Infiltmtor's tank Imlanatlon gap beneath pipe adapter. ",:I,. _ Note:To speed up the process of laslening the Ins W Olons. - 10.Do not over tighten screws.This may screws,Infiltrator recommends the use of an lit: 4.Align the 10 band phot Ides on damage the plastic parts be y , 14.Following tank backfilin visual examine the riser to initiator Ilia Polylok Rlser-lo-Riser Adapter \ all p pe inti connected, extended dol drives bit.(E72",150-300 mm). e 9 9 visually causing the screw connection to tall.This connector ung blot for damage resulting from backfill placement e- Reg filth the o receiving O hulas un may also strip the receiving hole.Reducing th 9.Tighten screws Ina°star'r patte,tat least screws on opposite stens of or replace If damaged.Allow a ntlnlrnum sealant caro time 0124 tows the ma baton connector ring using the aerew gun torque helps to prevent over- o w the ws Riser.Repeat the star seals at Chet ani a withonly du over tightening before testing or placing Into service. the swill.g made duMtg step two.Canter and press to amts an scows.lids MII compress the sealant to the tank evenly during fnaslerdrig. even seal Contact Infiltrator Water Technologles'Technical Services Department for assislaroe at 1-800-221-4438. Page 2 Contact inllltmter Water Technologlee'Tachnkal Sorvices Department for walstance at 1-880-221.4499.