|
•5.Faster.Polo ok Riser-to-RiserAda --- - --- - - - -
<br /> Ong using
<br /> g to to Infiltrator 1%-I connector 0,Fasten HDPE pipe to Infiltrator Pipe Adapter Ring using four 912 x 0.Place the IPEX plpo over the i
<br /> Ong using ten 914 z 1'A-Inch t �1i - i Vi-Inch(6.5 mm x 31 mm)stemless Inllltralor Pipe Adapter Ring willl
<br /> Appy 1311500 stainless steel screvrs. / teal straws from Inside tM i e. lt Is sealed at the base et the
<br /> pipe - AdheaNa Sealant enter
<br /> 0.Tighten screws In a"star'paltem, I T " flange. - Inala
<br /> lighlenirg screws on opposite sides a.Tighten screws In a'shul pattom, Oleg p!!a
<br /> 7 } lightening screws on opposite sides 10.Insert 151 1500 Adhesive
<br /> of the Repeat Riser
<br /> -to-Riser Riser Adapter 1 ° _°hI of the Infiltrator Pipe Adapter Ong. Sealant Into the(4)predrilled pilot s
<br /> Ring.Repeat star tightening
<br /> at least 6 I+.-� I Repeat the slur pattern at least twice, holes.
<br /> twice,without over tlghtaning screws. "s-'s over tlghtaning serevls. a 11.Fasten IPEX pipe to Infiltrator Pipe Adapter Rlrg using(4)912 z 1/2-
<br /> 17.n Spread the excess sealant between
<br /> the __-- Appy ISI 1560
<br /> ::rt W.Appy 1511500 Adhesive Sealant Inch stainless steel screws from the Inside of pipe.
<br /> Interior and exterior)int boAvtyn the - In the eco between the pipe A pilot a.bet
<br /> sP P P 12 Tighten screws In a'star' tlern,tightening screws on site
<br /> nt
<br /> tank and dyer with a small putty knife 9 Pa !9 g PPe Ir t r hales bet«e
<br /> S; and Infiltrator Pipe Adapter Ring to continuously 811 the gap. skies of the Infiltrator Pipe Adapter Ring.Repeal the InttalMg wovrs
<br /> or menuzy.Ensure There is even-
<br /> rr 11.Use the Infiltrator IM-Series septic.lank Ili,or star pattern at least Nice,svflMul over tightening screws.
<br /> coverage on both surfaces. P equivalent product
<br /> as a Ilo for the HDPE,pipe-Follow fid manufacturer's Instructions to 13. ISI 1500 Adhesive Sealant In the space between the pipe and
<br /> S.Connect PolyLok riser to PolyLok ""t I APPY P P P
<br /> comp ole riser Inslagatien. Inflliralor Pie Ade ter Rln to fill the e
<br /> Riser-to-Riser Adapter Ring and Install 3 P P g gap. Appy ISI tfiao
<br /> according to PolyInk's Instructions. ?• Se- 12.Back811 tank In accordance with Infiltratoes tank lostallallon 14.Apply a generous bead of sealant Into the groove at the base of the Adh-t.Sealant e8«
<br /> Note:Do not use the supplied 7 -..v i ?,.') Instructions. plpo mid then smear the sealant Into the groove behveen the pipe and Instel1IN p!pe.
<br /> Infiltrator tank fid,as It does not 13.Following lank backfilling,visually examine the riser to Infiltrator Infiltrator Pipe Adapter Ring.
<br /> provide a watertight seal with the PolyLok Riser system. Pipe Adapter Ring connection for damage resulting from back811 15.Use the Infiltrator tank lid,or equivalent product as a lid.Fnllmv Ili
<br /> placement.Repair or replace If damaged.Allow 24 hours sealant manufacturer's Instrucllons to complete riser Installation. Apply!Si Sea
<br /> In600
<br /> 9.Backfill lank In accordance vAlh InlNralor's tank Installation cure-ime before testing or putting Into service. bermo of ting pi
<br /> Instructions. 10.Backfill tank in accordance with In8ltretcr's tank Installation before rotating pipe
<br /> 10.Following tank backfilling,visually examine the riser to Infiltrator 24-inch(600-mm)IPEX Ultra-Rib]"PVC Pipe Instrucllons
<br /> Tank Adapter Ring connection for damage resulting from backfill Note:24-Inch(600-mm)IPEX pipe must be Installed using the 17.Following lank backfilling,visually examine the riser to Infiltrator
<br /> placement.Repair or replace If damaged.Allow 24 hours sealant we time Pipe Adapter Ring connection for damage resulting from backfill
<br /> before testing or putting Into service. --, placement.Rapak or replace if damaged.Allow 24 hours sealant
<br /> �. are time Wore testing or putting into scrrico. -
<br /> 24-inch(600-mm)HDPE Pipe
<br /> Note:The 24-Inch(600-mm)HDPE pipe must be Installed using fire
<br /> Infiffrafor Pipe Adep for Ring. _..T-• t
<br /> 3
<br /> �:Install riser assembly prior to backfilling tank. all,
<br /> ---
<br /> 2,_but HOPE pipe along an Inner corrugation to allow lid to fit property. Infiltrator Pipe Adapter Ring.
<br /> Cut should be smooth and even. 1.Install riser assembly prior to backfilling tank.
<br /> 2.Cul IPEX pipe along an Inner corrugation to ellmv lid to fit properly.
<br /> t Cul should be smooth and even.
<br /> a
<br /> 3.Apply 2 continuous 3f8'beads of ISI 1500 Adhesive Sealant in
<br /> alignment with the factory-drlged screw holes In the channel on the Disclaimer.Thane recommended procedures have been developed to Identify best practices for achieving a watertight connection between the tank
<br /> ,/ .••,�, top surface of Infiltrator connector Ong.Sealant Thickness must fig gap and dsor under typical lank Installation conditions.Those procedures have been shown to msn4t In a watertight connactfon bntvmon the riser assemblies
<br /> �' 4 ,•` �: beneath Infiltrator Pipe Adaptor Ong. Idendied In this document and the InfltratorlM-Tank.Infiltrator does not guarantee a watertight connection between tank and riser because achlevfng a
<br /> watertight connection Is dependent upon a comb/nation of inslaffor practices and procedures,and Hold conditions.Please contact In8llader's Technical
<br /> 4.Align the 10 blind pilot tales on the Infiltrator Pipe Adapter Ring Servl6es Department at 800-221-4436 If difficulty Is encountered during riser connection Installation.Please coninct the appropriate riser manufacturer
<br /> vdih the 10 receiving holes on the for concerns associated with anything that does not Involve the tank to-riser connection.
<br /> 3.Appy 2 continuous W11"beads of 181 1500 Adhesive Sealant In Infiltrator connector dng using the
<br /> alignment with the factory-drilled screw holes on the top surface of Indexing labs on the Inside of the
<br /> Infiltrator connector ring.Sealant thickness must fill gap beneath ring.Center and press to create an
<br /> Infiltrator Pipe Adapter Ring, even seal.
<br /> 4.Align the 10 blind pilot holes on the Infiltrator Pipe Adapter Ong with 6.Fasten Infiltrator Pipe Adapter
<br /> the 10 receiving holds on the Infiltrator connector Ong using the Indexing Hing lg hlflllndor connector Ong 5 N
<br /> using(en 914 x lyrinch stainless
<br /> tabs on the Inside of the Ong.Center and press to create an even seal. steel screws.Tighten in star pattern.Repeat the star pattern at feast
<br /> 6.Fasten Infiltrator Pipe Adapter Hing to Infiltrator rylInforcing ringusince twice,without over tightening sum-is, .
<br /> ten 914 x 1 y-Inch stainless steel 6.Mark(4)evenly spread locations on the Infiltrator Pipe Adaptor Ring
<br /> screws.Tighten In star pattern. i for pilot holes to accept screws.The pilot holes should be at a Might- 4 P.R-i
<br /> Repeal star patternat toast lwlco; i f68
<br /> hall way up the Interior gangs of P.O.s.ye,]°°k cr-16
<br /> without over tightening screvrs, the lnfiltralor Pipe Adapter Ring. ��.,,- ppy�q® aso-sn-rood•F..eaasn-]oat
<br /> 6.Spread excess sealant In the t 1 Vp�F I L T R 1 V'a a' 1.900-ni-4436
<br /> 7.Drill(4)1/8-inch(3.5-mm)plot T�•�!e!sa*tea+�«<°m
<br /> Interior Joint between the leek and holes at marked locations \
<br /> water technologies
<br /> riser
<br /> with Athasmall putty knife or 7 on the Infiltrator Pipe Adapter ll.y.M14n'e 4,)39,e61;4a1T,all;5,i5e,U9;e,Ile,el];b,.ar,118;5,4a1,459;49I1,BN;e,]IQtet;49ee,)]B;a,619,bU CeneA.r,P°M.ex I�P.0,a5'1,e,0o1,6e1 Oaep°Imlapertig.Nryy.ar,
<br /> manually.
<br /> Fling. Fq•+abar.O.utA,n4 SHelriW.n naairtl e.dmY aNea.brlY°ler TecNabaM°.trdYlnl«berog"sltttletlmwkhFrsrce.e,flvebrl'lWrTrlawbpfee le.regitctleW�rakn A!eakn.
<br /> Contatr,rf dmdd,q,PNM.CIwrbbypaw,lAWPM,PmIa{cQWG:l OuicYF.y.avptrcnW Msy9aokuev alaanlalvMrrorH,Woq'ce.
<br /> 7.Center the HOPE pipe over the Inflltmtm Pipe Adapter Ring. fWl,a u.stlesovsa paxrwk,Ino T MF a..<omrw v.4. wn)F TRF•rvc.um.-wev.a°n«M,x a IrFx leo.
<br /> B.Appy(2)beads of 1511500 s oe9isuc.M dy,ieoaa.comedo uar.
<br /> Note:Use additional IS11500AdhesNe Sealant to NI gap and seat Adhesive Sealant to the In9ltrater T,wxazone
<br /> . .. - ....
<br /> space behveen the HDPEpIpe and Infllfmt6rPlpe Adapter Ring. i Pipe Adapter Ring at the base of the flange. �:�,QTaf.$1�1� ^]?e ..I •:51. 1 @a' - .Px�4k4kYTo a 9.�e a
<br /> Contact Infiltrator Water Technologles'Tedink:al SoMce,Department for assistance at 1-800-221-4436. Page 3
<br />
|