|
2/2/2
<br />ABBREVIATIONS
<br />@
<br />AT
<br />FLA
<br />FULL LOAD AMP
<br />OLCP
<br />OUTDOOR LIGHTING CONTROL PANEL
<br />A, AMPS
<br />AMPERES
<br />G
<br />GREEN GROUND WIRE
<br />O.C.
<br />ON CENTER
<br />A.C.
<br />ABOVE COUNTER
<br />GND
<br />GROUND
<br />0
<br />PHASE
<br />AF
<br />AMPERE FRAME
<br />GFI
<br />GROUND FAULT INTERRUPTER
<br />P
<br />POLE
<br />A.F.F.
<br />ABOVE FINISH FLOOR
<br />HID
<br />HIGH INTENSITY DISCHARGE
<br />P.A.
<br />PUBLIC ADDRESS SYSTEM
<br />AL
<br />ALUMINUM CONDUCTOR OR BUS
<br />HP
<br />HORSEPOWER
<br />PB
<br />PULL BOX
<br />ARCH
<br />ARCHITECT
<br />HPS
<br />HIGH PRESSURE SODIUM (LAMP)
<br />PNL
<br />PANEL
<br />AT
<br />AMPERE TRIP
<br />ILCP
<br />INDOOR LIGHTING CONTROL PANEL
<br />RS
<br />RAPID START
<br />ATS
<br />AUTOMATIC TRANSFER SWITCH
<br />I.B.O.
<br />INSTALLED BY OTHERS
<br />REC
<br />RECEPTACLE
<br />C
<br />CONDUIT
<br />I.B.E.
<br />INSTALLED AND CONNECTED BY ELECTRICAL
<br />RM
<br />ROOM
<br />CKT
<br />CIRCUIT
<br />c
<br />�
<br />CONTRACTOR
<br />SPST
<br />SINGLE POLE SINGLE THROWN
<br />CAB
<br />CABINET
<br />JB
<br />JUNCTION BOX
<br />S. L.
<br />SECURITY LIGHT, ON/OFF BY
<br />CB
<br />CIRCUIT BREAKER
<br />KV
<br />KILOVOLTS
<br />PHOTO -ELECTRIC CELL
<br />CO
<br />CONDUIT ONLY (EMPTY CONDUIT) WITH PULL WIRE
<br />KVA
<br />KILOVOLT -AMPERES
<br />SW
<br />SWITCH
<br />CU
<br />COPPER CONDUCTOR OR BUS
<br />KW
<br />KILOWATTS
<br />TS
<br />TAMPER SWITCH
<br />D
<br />DEDICATED CIRCUIT
<br />LV
<br />LOW VOLTAGE
<br />TEL
<br />TELEPHONE
<br />DN
<br />DOWN
<br />LTG
<br />LIGHTING
<br />TYP
<br />TYPICAL
<br />DPST
<br />DOUBLE POLE SINGLE THROWN
<br />MCA
<br />MINIMUM CIRCUIT AMPACITY
<br />TTB
<br />TELEPHONE TERMINAL BOARD
<br />DIA
<br />DIAMETER
<br />MCC
<br />MOTOR CONTROL CENTER
<br />TTC
<br />TELEPHONE TERMINAL CABINET
<br />EMT
<br />ELECTRIC METALLIC TUBING
<br />MOCP
<br />MAXIMUM OVERCURRENT PROTECTION
<br />U.C.
<br />UNDER COUNTER
<br />EWC
<br />ELECTRIC WATER COOLER
<br />MTD
<br />MOUNTED
<br />UG
<br />UNDERGROUND
<br />EM
<br />EMERGENCY
<br />MTG
<br />MOUNTING
<br />UON
<br />UNLESS OTHERWISE NOTED
<br />(E)
<br />EXISTING
<br />MLO
<br />MAIN LUG ONLY
<br />V
<br />VOLTS/VOLTAGE
<br />E.O.L.
<br />END -OF -LINE DEVICE
<br />N
<br />NEUTRAL
<br />VA
<br />VOLT-AMPERE
<br />F
<br />FUSE
<br />NEC
<br />NATIONAL ELEC. CODE
<br />W
<br />WATTS
<br />FS
<br />FLOW SWITCH
<br />NL
<br />NIGHT LIGHT
<br />WP
<br />WEATHERPROOF
<br />F.A.
<br />FIRE ALARM
<br />NIC
<br />NOT IN CONTRACT
<br />WM
<br />WIREMOLD
<br />FACP
<br />FIRE ALARM CONTROL PANEL
<br />NTS
<br />NOT TO SCALE
<br />XP
<br />EXPLOSION PROOF
<br />F.B.O
<br />FURNISHED BY OTHERS/FURNISHED BY OWNER
<br />SYMBOLS
<br />(NOTE: NOT ALL SYMBOLS ARE USED IN DRAWINGS)
<br />cR DUPLEX RECEPTACLE - 20A, 125V, GROUND
<br />GFI DNOTES "GROUND FAULT INTERRUPTER"
<br />wP WP DENOTES "WEATHERPROOF"
<br />O
<br />1x
<br />3,
<br />DOUBLE DUPLEX RECEPTACLE - (2) 20A, 125V, GROUND
<br />SPECIAL RECEPTACLE - NEMA TYPE AS NOTED ON DWGS
<br />(VERIFY NEMA TYPE WITH EQUIPMENT NAMEPLATE PRIOR TO ROUGH -IN)
<br />+18" AFF, LION
<br />CONFIRM HEIGHT OF RECEPTACLES AT
<br />COUNTER PRIOR TO ROUGH -IN.
<br />(VERIFY LOCATION AND HEIGHT OF
<br />EQUIPMENT RECEPTACLES IN FIELD)
<br />WALL SWITCH "ROCKER TYPE"- 20A, 120/277V, "a" INDICATES CONTROL. +48" AFF, UON
<br />"D" INDICATES DIMMER - COMPATIBLE WITH LIGHTS PROVIDED
<br />MANUAL MOTOR STARTER WITH OVER LOAD PROTECTION. SIZE PER CODE.
<br />WALL MOUNTED
<br />OCCUPANCY
<br />SENSOR , APPLY PER
<br />MANUFACTURER GUIDELINES.
<br />JUNCTION BOX -
<br />CEILING OR
<br />WALL MOUNTED, SIZED
<br />PER CODE.
<br />DUCT SMOKE DETECTOR. PROVIDE 120V CONNECTION.
<br />PANELBOARD
<br />EDJ DISCONNECT SWITCH - MOTOR RATED AND FUSIBLE
<br />- CONDUIT - CONCEALED IN CEILING OR WALL.
<br />HASH MARKS INDICATE NUMBER PHASE (SHORT) AND NEUTRAL (LONG) WIRES.
<br />UON, SIZE CONDUIT AND WIRE PER CODE.
<br />T ISOLATED GROUND WIRE
<br />�- GROUND WIRE WIRE, GREEN INSULATION. SIZE PER NEC U.O.N.
<br />UP
<br />CONDUIT - STUB -UP OR DOWN AS NOTED
<br />DN
<br />CONDUIT - HOME RUN TO PANEL, TERMINAL CABINET, ETC.: HASH MARKS
<br />'#10 INDICATE NUMBER OF WIRES. "#10" INDICATES WIRE SIZE, SIZE CONDUIT
<br />PER NEC U.O.N. PROVIDE J-BOX(ES)/SPLICE BOXES AS REQUIRED.
<br />MINIMUM CONDUCTOR SIZE TO BE #12 AWG.
<br />30A/3P CIRCUIT BREAKER (A: AMPACITY, P: No. OF POLE)
<br />�y MOTOR FURNISHED AND INSTALLED BY OTHERS AND
<br />IBJ CONNECTED BY ELECTRICAL CONTRACTOR
<br />p DATA WALL OUTLET - PROVIDE RING WITH PULL WIRE
<br />UP TO ACCESSIBLE CEILING SPACE U.O.N.
<br />TELEPHONE WALL OUTLET - PROVIDE RING WITH PULL WIRE
<br />UP TO ACCESSIBLE CEILING SPACE U.O.N.
<br />1O SHEET NOTE #1 - SEE ASSOCIATED NOTE ON SAME SHEET
<br />Al REVISION #2 - SEE ASSOCIATED REVISION NOTE
<br />3
<br />REFERENCE TO PLAN/DETAIL/DIAGRAM #1 ON SHEET E-3
<br />�17 8:03:10 AM
<br />CODE REFERENCE
<br />ALL
<br />WORK
<br />SHALL COMPLY WITH FOLLOWING STATE CODES ALONG WITH
<br />ANY
<br />LOCAL
<br />CITY AMENDMENTS
<br />TO FIELD
<br />AND/OR ORDINANCES, PUBLISHED UNDER
<br />CALIFORNIA
<br />CODE OF
<br />REGULATIONS
<br />(CCR), TITLE 24:
<br />Part
<br />1
<br />- 2016
<br />California
<br />Administrative Code
<br />Part
<br />2
<br />- 2016
<br />California
<br />Building Code, Volumes 1 and 2
<br />Part
<br />2.5
<br />- 2016
<br />California
<br />Residential Code
<br />Part
<br />3
<br />- 2016
<br />California
<br />Electrical Code
<br />Part
<br />4
<br />- 2016
<br />California
<br />Mechanical Code
<br />Part
<br />5
<br />- 2016
<br />California
<br />Plumbing Code
<br />Part
<br />6
<br />- 2016
<br />California
<br />Energy Code
<br />PROGRAMMABLE TIME CLOCK TO MEET
<br />REQUIREMENTS OF CALIFORNIA'S BUILDING ENERGY
<br />EFFICIENCY STANDARDS. INSTALL TIMECLOCK AND
<br />CONTACTORS IN A NEMA 1 ENCLOSURE. PROVIDE
<br />WITH A LOCAL OVERRIDE PUSH BUTTON.
<br />ELECTRICAL CONTRACTOR SHALL PROVIDE INITIAL
<br />PROGRAMMING OF THE TIME CLOCK PER OWNER'S
<br />REQUIREMENTS.
<br />LIGHTING CONTROL DIAGRAM
<br />SCALE: NONE
<br />1. IT IS THE CONTRACTORS RESPONSIBILITY TO INSURE THAT THE INSTALLATION METHODS AND
<br />MATERIALS FULLY CONFORM TO BUILDING CODES LISTED UNDER CODE REFERENCE ON THIS SHEET.
<br />2. PROVIDE ALL LABOR, EQUIPMENT, DEVICES, AND INCIDENTAL MATERIALS AS SHOWN AND AS
<br />REQUIRED FOR A COMPLETELY OPERATIONAL AND FUNCTIONAL ELECTRICAL SYSTEM. ELECTRICAL
<br />CONTRACTOR SHALL VISIT THE PROJECT SITE PRIOR TO BID. ELECTRICAL CONTRACTOR SHALL
<br />INCLUDE ALL COSTS NECESSARY FOR A COMPLETE AND FUNCTIONAL ELECTRICAL SYSTEM BASED
<br />ON APPLICABLE CODES, DRAWINGS AND SPECIFICATIONS.
<br />3. INSTALL ALL WORK NEATLY. RACEWAYS, FITTINGS AND EQUIPMENT: LEVEL, PLUMB AND STRAIGHT,
<br />CONNECTORS, LOCKNUTS, SCREWS, CLAMPS: MADE UP TIGHTLY. CLEAR BEAMS OR OBSTRUCTIONS.
<br />DO NOT CUT INTO OR REDUCE SIZE OF LOAD CARRYING MEMBERS.
<br />4. TRADE COORDINATION: CHECK DRAWINGS AND WORK OF TRADES TO PREVENT INTERFERENCES.
<br />5. DRAWINGS ARE DIAGRAMMATIC: REFER TO ARCHITECTURAL DRAWINGS FOR EXACT LOCATION OF
<br />OUTLETS, PLACEMENT OF LIGHTING FIXTURES, AND RECEPTACLES.
<br />6. PROVIDE ALL MATERIALS NEW, PACKAGED IN ORIGINAL CONTAINERS, INSTALLED AND FREE OF
<br />DEFECTS. ALL EQUIPMENT TO BE LISTED BY U.L. OR APPROVED EQUAL TESTING LABORATORY.
<br />ALL RACEWAY SYSTEMS TO BE SUPPORTED INDEPENDENT OF SUSPENDED CEILING, INCLUDING BUT
<br />NOT LIMITED TO POWER, TELEPHONE, DATA, AND LOW VOLTAGE WIRING SYSTEMS.
<br />7. PROVIDE UL APPROVED FIRE PROOFING AT ALL PENETRATIONS THROUGH FIRE -RATED PARTITIONS.
<br />8. PROVIDE BRACING OF ELECTRICAL EQUIPMENT TO MEET THE STATE OF CALIFORNIA REQUIREMENTS
<br />FOR ZONE 4 EARTH QUAKE REGIONS.
<br />9. ALL ELECTRICAL SWITCHBOARDS AND PANELS REQUIRING EXAMINATION OR SERVICING WHILE
<br />ENERGIZED SHALL BE FIELD -MARKED TO WARN QUALIFIED PERSONS OF POTENTIAL OF ARC FLASH
<br />HAZARDS PER CEC 110.16. MARKING SHALL BE CLEARLY VISIBLE TO QUALIFIED PERSONS BEFORE
<br />EXAMINATION, ADJUSTMENT, SERVICING, OR MAINTENANCE.
<br />10. ELECTRICAL EQUIPMENT AND DEVICES ASSOCIATED WITH BUILDING SIGNS, SUCH AS LAMP BALLASTS,
<br />TRANSFORMERS, AND POWER SUPPLIES SHALL NOT BE LOCATED IN SOFFITS, MANSARDS AND
<br />ATTICS.
<br />11. ALL NEW CONDUITS AND CABLES SHALL BE CONCEALED, UNLESS OTHERWISE NOTED.
<br />12. ALL EXISTING TO REMAIN LOADS TO BE KEPT ENERGIZED. ANY INTERRUPTION OF POWER SHALL BE
<br />COORDINATED IN ADVANCE WITH OWNER.
<br />13. PROVIDE CODE COMPLIANT TERMINATIONS AT PANELBOARDS, DISCONNECTS, CIRCUIT BREAKERS,
<br />DEVICES, LIGHT FIXTURES, CONTROLLERS, AND MOTORS. FOLLOW MANUFACTURER'S
<br />RECOMMENDATIONS FOR TORQUE VALUES.
<br />14. USE #12 AWG MINIMUM WIRE WHEN SIZE IS NOT INDICATED ON DRAWINGS. SIZE CONDUIT PER
<br />CODE. PROVIDE GREEN INSULATED EQUIPMENT GROUNDING CONDUCTOR IN ALL CIRCUITS.
<br />15. REMOVE ALL DEBRIS RELATED TO ELECTRICAL CONSTRUCTION FROM PROJECT SITE ON A REGULAR
<br />BASIS.
<br />16. ELECTRICAL EQUIPMENT AND MATERIALS TO BE LISTED, LABELED, AND INSTALLED PER A
<br />RECOGNIZED ELECTRICAL TESTING LABORATORY.
<br />17. CONNECT T -BAR DROP-IN FIXTURES AT DIAGONAL CORNERS DIRECTLY TO STRUCTURE OVERHEAD
<br />USING MINIMUM #1 WIRE. CLIPS ARE NOT SUITABLE IN SEISMIC ZONE #4.
<br />18. THE AMPACITY OF THE CONDUCTOR SIZES, #14 THROUGH #1, SHALL BE RATED AT 60 DEGREES
<br />CENTIGRADE.
<br />19.
<br />SEPARATE PERMIT REQUIRED FOR SIGNS
<br />AND FIRE
<br />ALARM SYSTEMS.
<br />20.
<br />ALL ELECTRICAL WORK TO BE SUBJECT
<br />TO FIELD
<br />INSPECTION.
<br />21. ELECTRICAL CONTRACTOR (EC) SHALL CONFIRM IN FIELD PRIOR TO INSTALLATION THE METHOD OF
<br />POWER CONNECTION TO EACH EQUIPMENT, WHETHER HARD -WIRED OR VIA RECEPTACLE. EC SHALL
<br />COORDINATE ROUTING OF CONDUITS AND CIRCUITS TO FINAL CONNECTION POINT TO THE
<br />EQUIPMENT WITH GENERAL CONTRACTOR AND/OR OWNER IN FIELD PRIOR TO INSTALLATION. EC
<br />SHALL PROVIDE TRENCHING, INSTALLATIONS IN CABINETS AS REQUIRED TO PROVIDE REQUIRED
<br />POWER CONNECTION TO EACH EQUIPMENT.
<br />22. VERIFY FINISHES OF ALL DEVICES, COVER PLATES, AND LIGHT FIXTURES WITH ARCHITECT AND/OR
<br />OWNER.
<br />23. ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR FIRE ALARM DESIGN AND INTERFACE WITH EXISTING
<br />BUILDING FIRE ALARM SYSTEM. DETERMINE THE QUANTITY AND LOCATION OF DETECTION AND/OR
<br />NOTIFICATION DEVICES NEEDED IN SUBWAY SPACE AND OBTAIN PERMIT FROM LOCAL
<br />FIRE MARSHAL.
<br />24. MOUNT ALL ELECTRICAL DEVICES, INCLUDING RECEPTACLES AND SWITCHES FLUSH TO SURFACE,
<br />UNLESS NOTED OTHERWISE.
<br />25. PROVIDE WARRANTY PERIOD OF ONE YEAR FOR ALL ELECTRICAL WORK.
<br />26. ELECTRICAL CONTRACTOR SHALL HIRE THE SERVICES OF AN ACCEPTANCE TECH (AT) TO PROVIDE
<br />INSTALLATION AND ACCEPTANCE DOCUMENTATION AS REQUIRED BY LOCAL AUTHORITY HAVING
<br />JURISDICTION TO APPROVE LIGHTING FIXTURES AND LIGHTING CONTROLS.
<br />ire
<br />z
<br />0
<br />w
<br />w
<br />.....
<br />ca
<br />a)
<br />o
<br />@
<br />co
<br />O
<br />N
<br />� .5
<br />CV
<br />Y
<br />J
<br />c i
<br />�
<br />a y
<br />0)
<br />Ec
<br />00
<br />a)_Lu
<br />c
<br />a) U
<br />z
<br />o
<br />C6 - a
<br />E
<br />c
<br />v
<br />t,-
<br />,=
<br />(Lw0M
<br />w o
<br />u�
<br />as
<br />)
<br />`
<br />a)
<br />co
<br />.9
<br />O N
<br />�
<br />N
<br />a?
<br />C
<br />N O
<br />Coo)
<br />-j
<br />cocoEc-
<br />U
<br />4
<br />O^
<br />O
<br />8O
<br />U
<br />0) a)
<br />a)
<br />U)
<br />)Q
<br />'
<br />(�
<br />� a)
<br />c6 >
<br />-d
<br />c
<br />�
<br />O
<br />o_ L
<br />LL
<br />a
<br />'o
<br />M
<br />U
<br />J
<br />c
<br />.....
<br />ca
<br />a)
<br />o
<br />@
<br />DWG
<br />O
<br />N
<br />ca
<br />fc6 . V
<br />Qi
<br />Y
<br />J
<br />c i
<br />�
<br />2 a) a)
<br />O 0
<br />a)_Lu
<br />c
<br />OrQ
<br />o
<br />C6 - a
<br />E
<br />v
<br />t,-
<br />,=
<br />(Lw0M
<br />W w i
<br />O U)
<br />F -
<br />Z
<br />LED
<br />LU
<br />w�Ll
<br />L >H0)'
<br />0f OC/)Q
<br />CO Q00
<br />Ui,
<br />Q �ofz
<br />co I - 00I'
<br />C/) Z i
<br />J WVO
<br />U
<br />m F-
<br />C.00
<br />U)
<br />C
<br />L
<br />O~
<br />U
<br />w
<br />_1z0
<br />F= a
<br />A�EET S.
<br />�£ m
<br />E 15692 z
<br />E%P.6-30-16 /*
<br />� OF CAUF�
<br />DATE:
<br />01117/2017
<br />JOB:
<br />PTST-05
<br />DWG
<br />BY: PSG
<br />CHK
<br />BY: PSG
<br />E0.1
<br />
|