|
water piping; Cooling condensate drain piping insulation; fasteners not permitted Watts Regulator Company, AGA Z21.22 certified, bronze body, teflon seat, stainless
<br /> 3.01 INSTALLATION steel stem and springs, automatic, direct pressure actuated, temperature relief _
<br /> A. Determine that roof structure, roof insulation, and roof membrane are structurally PART 2 PRODUCTS PART 3 EXECUTION maximum 210 degrees F, capacity ASME (BPV IV) certified and labeled.
<br /> adequate to support weight of pipe, duct, conduit, and supports and hangers. 2.18 STRAINERS
<br /> B. Install supports and hangers in accordance with manufacturer's recommendations. 2.01 REQUIREMENTS FOR ALL PRODUCTS OF THIS SECTION 3.01 EXAMINATION A. Manufacturers: Armstrong International, Inc; Green Country Filtration; WEAMCO.
<br /> C. Install supports at maximum spacing of 10 feet unless closer spacing is required A. Surface Burning Characteristics: Flame spread/Smoke developed index of 25/50, A. Verify that piping configurations are correct type for piping cover component B. Size 2 inch and Under: Threaded brass body for 175 psi CWP, Y pattern with 1/32
<br /> due to weight of pipe or conduit contents or greater spacing is specifically maximum, when tested in accordance with ASTM E 84, NFPA 255, or UL 723. configurations specified. inch stainless steel perforated screen. Wr
<br /> allowed by manufacturer; space and adjust to support an equal amount of weight; do B. The Contractor may use any of the following insulating/jacketing materials, at his 3.02 INSTALLATION 2. Class 150, threaded bronze body 300 psi CWP, Y pattern with 1/32 inch
<br /> not exceed manufacturer's recommended load limits. option, provided the selected material meets with the approval of all State, local A. Install products of this section in accordance with manufacturer's printed stainless steel perforated screen.
<br /> D. Remove roofing aggregate from area 2 inches larger than support base; comply with authorities and utility company requirements. Verification of compliance of the installation instructions. C. Size 1-1/2 inch to 4 inch: Class 125, flanged iron body, Y pattern with 1/16 inch
<br /> roofing manufacturer's requirements to maintain roofing warranty. selected insulating/jacketing material is the sole responsibility of the installing 3.03 PROTECTION OF INSTALLED PRODUCTS stainless steel perforated screen.
<br /> E. Install an additional sheet of roofing material, support pad, or deck plate beneath Contractor. A. Do not allow damage to installed products by subsequent construction activities; D. Size 5 inch and Larger: Class 125, flanged iron body, basket pattern with 1/8 inch
<br /> each support base. 2.02 GLASS FIBER protect products until Substantial Completion. Replace any damaged products prior stainless steel perforated screen.
<br /> F. Support Pads: Remove rock, aggregate, dirt and excess dust from area to be covered A. Manufacturers: Knauf Insulation; Johns Manville Corporation; Owens Corning Corp; to occupancy.
<br /> by pad; Apply support pad on cleaned area; Center bases on top of support pads. CertainTeed Corporation. PART 3 EXECUTION
<br /> G. Deck Plates: Required for loads greater than 100 pounds per support; Locate B. Insulation: ASTM C 547 and ASTM C 795; rigid molded, noncombustible; 'K' value: END OF SECTION
<br /> centered under bases of pipe supports and hangers; Remove rock, aggregate, dirt and ASTM C 177, 0.24 at 75 degrees F, Maximum service temperature: 850 degrees F; 3.01 EXAMINATION
<br /> excess dust from an area 2 inches larger than deck plate; Install with curved edges Maximum moisture absorption: 0.2 percent by volume. SECTION 221005 – PLUMBING PIPING A. Verify that excavations are to required grade, dry, and not over–excavated. ©2017 STARBUCKS COFFEE COMPANY
<br /> up. C. Insulation: ASTM C 547 and ASTM C 795; semi–rigid, noncombustible, end grain 3.02 PREPARATION
<br /> H. Pipe Supports: Center beneath pipe so that pipe is located squarely over and adhered to jacket; 'K' value: ASTM C 177, 0.24 at 75 degrees F; Maximum service PART 1 GENERAL A. Ream pipe and tube ends. Remove burrs. Bevel plain end ferrous pipe.
<br /> through cradle or hanger. Set pipe in support without dropping or causing undue temperature: 650 degrees F; Maximum moisture absorption: 0.2 percent by volume. B. Remove scale and dirt, on inside and outside, before assembly. STARBUCKS COFFEE
<br /> impact. D. Vapor Barrier Jacket: White kraft paper with glass fiber yarn, bonded to 1.01 SECTION INCLUDES C. Prepare piping connections to equipment with flanges or unions.
<br /> I. All roofing penetrations shall be flashed and weather sealed by the roofing aluminized film; moisture vapor transmission when tested in accordance with ASTM E A. Pipe, pipe fittings, valves, and connections for piping systems: Sanitary sewer, 3.03 INSTALLATION COMPANY
<br /> manufacturer's authorized roofing contractor at this Contractor's expense. This 96/E 96M of 0.02 perm–inches. interior; Sanitary sewer, exterior; Domestic water, interior; Domestic and fire A. Install in accordance with manufacturer's instructions.
<br /> Contractor shall contract with the factory authorized roofing contractor for the E. Vapor Barrier Lap Adhesive: Compatible with insulation. service water, exterior; Natural gas, interior. B. Provide non–conducting dielectric connections wherever jointing dissimilar metals. 2401 UTAH AVENUE SOUTH
<br /> specific roofing system applicable to this project. The use of an unauthorized F. Insulating Cement/Mastic: ASTM C 195; hydraulic setting on mineral wool. C. Route piping in orderly manner and maintain gradient. Route parallel and SEATTLE WASHINGTON 98134
<br /> roofing contractor may result in removal and replacement of the penetration systems G. Fibrous Glass Fabric: Cloth: Untreated; 9 oz/sq yd weight; Blanket: 1.0 Ib/cu ft PART 2 PRODUCTS perpendicular to walls.
<br /> at this Contractor's expense. density, Weave: 5x5. D. Install piping to maintain headroom, conserve space, and not interfere with use of (206)318-1575
<br /> 3.02 FIELD QUALITY CONTROL H. Indoor Vapor Barrier Finish: Vinyl emulsion type acrylic, compatible with 2.01 The Contractor may use any of the following piping materials, at his option, provided the space.
<br /> A. After system startup, correct any deficiencies that arise, including but not insulation, white color; Outdoor Vapor Barrier Mastic: Vinyl emulsion type acrylic selected material meets with the approval of all State and local authorities and utility E. Group piping whenever practical at common elevations.
<br /> limited to, improper location or position, improper seating or level on the roof, or mastic, compatible with insulation, black color; Outdoor Breather Mastic: Vinyl company requirements. Verification of compliance of the selected piping material with F. Install piping to allow for expansion and contraction without stressing pipe, THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> lack of roof pads or deck plates, inadequate operation, and as directed by emulsion type acrylic or mastic, compatible with insulation, black color. local requirements is the sole responsibility of the installing Contractor. Verify the joints, or connected equipment. CONFIDENTIAL AND SHALL REMAIN THE SOLE
<br /> Engineer. K. Insulating Cement: ASTM C 449/C 449M. use of plastic piping systems with the local jurisdiction. Non–metallic piping systems G. Provide clearance in hangers and from structure and other equipment for PROPERTY OF STARBUCKS CORPORATION,
<br /> 2.03 FLEXIBLE ELASTOMERIC CELLULAR INSULATION may not be used in any return air plenum ceiling spaces. No exceptions. installation of insulation and access to valves and fittings. WHICH IS THE OWNER OF THE COPYRIGHT IN
<br /> END OF SECTION A. Manufacturer: Armacell International; 2.02 SANITARY SEWER PIPING, BURIED BEYOND 5 FEET OF BUILDING H. Locate all valves and control elements in accessible areas wherever possible to THIS WORK. THEY SHALL NOT BE
<br /> B. Insulation: Preformed flexible elastomeric cellular rubber insulation complying A. Cast Iron Pipe: ASTM A 74 service weight; Fittings: Cast iron; Joint Seals: ASTM avoid access doors. Provide access where valves and fittings are not exposed or
<br /> SECTION 220548 – VIBRATION AND SEISMIC CONTROLS FOR PLUMBING PIPING AND EQUIPMENT with ASTM C 534 Grade 1; use molded tubular material wherever possible; Minimum C 564 neoprene gaskets, or lead and oakum. located in accessible areas. Provide ceiling access doors for access to all valves REPRODUCED(IN WHOLE OR IN PART), SHARED
<br /> Service Temperature: –40 degrees F; Maximum Service Temperature: 220 degrees F; B. Vitrified Clay Pipe: ASTM C 700, Standard Strength; Fittings: Clay; Joints: and control elements located above inaccessible ceiling areas. Provide minimum 12 WITH THIRD PARTIES OR USED IN ANY MANNER
<br /> PART 1 GENERAL Connection: Waterproof vapor barrier adhesive. Bell–and–spigot, with ASTM C 425 compression joint device. x 12 inch size for hand access, 18 x 18 inch size for shoulder access, and as ON OTHER PROJECTS OR EXTENSIONS TO THIS
<br /> C. Elastomeric Foam Adhesive: Air dried, contact adhesive, compatible with C. ABS Pipe: ASTM D 2751, ASTM F 628, ASTM D2661, or ASTM D2751; Fittings: ABS; indicated. Provide 4 x 4 inch for shut off valves only. Provide rated access doors PROJECT WITHOUT THE PRIOR WRITTEN
<br /> 1.01 SECTION INCLUDES insulation. Joints: Solvent welded with ASTM D 2235 cement. where installed in fire rated construction. Review locations prior to CONSENT OF STARBUCKS CORPORATION.
<br /> A. Concrete housekeeping pads; Vibration isolators; Seismic restraints. 2.04 JACKETS 2.03 SANITARY SEWER PIPING, BURIED WITHIN 5 FEET OF BUILDING fabrication. THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> A. PVC Plastic. A. Cast Iron Pipe: ASTM A 74 service weight; Fittings: Cast iron; Joints: I. Establish elevations of buried piping outside the building to ensure not less than
<br /> PART 2 PRODUCTS 1. Manufacturers: Knauf Fiber Glass; Johns Manville Corporation; Owens Corning Hub–and–spigot, CISPI HSN compression type with ASTM C 564 neoprene gaskets or lead the maximum local frost depth cover. Install tracer wire on all plastic piping INTENDED TO EXPRESS DESIGN INTENT FOR A
<br /> Corp; CertainTeed Corporation. and oakum. outside the building. PROTOTYPICAL STARBUCKS STORE(WHICH IS
<br /> 2.01 MANUFACTURERS 2. Jacket: One piece molded type fitting covers and sheet material, off–white B. ABS Pipe: ASTM D 2751, ASTM F 628, ASTM D2661, or ASTM D2751; Fittings: ABS; J. Install vent piping penetrating roofed areas to maintain integrity of roof SUBJECT TO CHANGE AT ANYTIME)AND DO
<br /> A. Isolation Technology, Inc.; Kinetics Noise Control, Inc.; Mason Industries. color; Minimum Service Temperature: 0 degrees F; Maximum Service Joints: Solvent welded with ASTM D 2235 cement. assembly. NOT REFLECT ACTUAL SITE CONDITIONS.
<br /> 2.02 BASES Temperature: 150 degrees F; Moisture Vapor Permeability: 0.002 perm inch, 2.04 SANITARY SEWER PIPING, ABOVE GRADE K. All roofing penetrations shall be flashed and weather sealed by the roofing
<br /> A. Concrete Housekeeping Pad: Construction: Concrete as specified for flooring; maximum, when tested in accordance with ASTM E 96/E 96M; Thickness: 10 mil; A. Cast Iron Pipe: ASTM A 74, service weight; Fittings: Cast iron; Joint Seals: manufacturer's authorized roofing contractor at this Contractor's expense. This NEITHER PARTY SHALL HAVE ANY OBLIGATION
<br /> Design: 4" high above the surrounding finished flooring and 4" greater in dimension Connections: Brush on welding adhesive; Covering Adhesive Mastic: ASTM C 564 neoprene gaskets, or lead and oakum. Contractor shall contract with the factory authorized roofing contractor for the NOR LIABILITY TO THE OTHER(EXCEPT STATED
<br /> that the equipment supported, or greater if detailed on the Drawings or when Compatible with insulation. B. Cast Iron Pipe: CISPI 301, hubless, service weight; Fittings: Cast iron; Joints: specific roofing system applicable to this Project. The use of an unauthorized ABOVE)UNTIL A WRITTEN AGREEMENT IS
<br /> indicated. B. ABS Plastic: CISPI 310, neoprene gaskets and stainless steel clamp–and–shield assemblies. roofing contractormay result in removal and replacement of the penetration systems FULLY EXECUTED BY BOTH PARTIES.
<br /> 2.03 VIBRATION ISOLATORS 1. Jacket: One piece molded type fitting covers and sheet material, off–white 2.05 WATER PIPING, BURIED BEYOND 5 FEET OF BUILDING at this Contractor's expense.
<br /> A. Restrained Open Spring Isolators: Springs: Minimum horizontal stiffness equal to color; Minimum Service Temperature: –40 degrees F, Maximum Service A. Ductile Iron Pipe: AWWA C151/A21.51; Fittings: AWWA C110, ductile or gray iron, L. All sanitary vent system terminations shall be a minimum of ten feet from any fresh
<br /> 75 percent vertical stiffness, with working deflection between 0.3 and 0.6 of Temperature of 180 degrees F; Moisture Vapor Permeability. 0.012 perm inch, standard thickness; Joints: AWWA C111/A21.11, rubber gasket with 3/4 inch diameter air intake and twenty–five feet on medical facilities (hospitals, clinics, etc.)
<br /> maximum deflection. Color code springs for load carrying capacity, Spring Mounts: when tested in accordance with ASTM E 96/E 96M; Thickness: 30 mil.; rods. M. Where pipe support members are welded to structural building framing, scrape, brush ARCHITECT OF RECORD
<br /> Provide with leveling devices, minimum 0.25 inch thick neoprene sound pads, and Connections: Brush on welding adhesive. B. Copper Pipe: ASTM B 42, hard drawn; Fittings: ASME B16.18, cast copper alloy or clean, and apply one coat of zinc rich primer to welding. mcg architecture
<br /> zinc chromate plated hardware; Sound Pads: Size for minimum deflection of 0.05 C. Aluminum Jacket: ASTM B 209 (ASTM B 209M) formed aluminum sheet; Thickness: 0.016 ASME B16.22 wrought copper and bronze; Joints: ASTM B 32, alloy Sn95 solder. N. Provide support for utility meters in accordance with requirements of utility
<br /> inch; meet requirements for neoprene pad isolators; Restraint: Provide heavy inch sheet; Finish: Embossed; Joining: Longitudinal slip joints and 2 inch laps; 2.06 WATER PIPING, BURIED WITHIN 5 FEET OF BUILDING companies. U c > ._
<br /> mounting frame and limit stops; For Exterior and Humid Areas: Hot dipped Fittings: 0.016 inch thick die shaped fitting covers with factory attached A. Copper Pipe: ASTM B 42, hard drawn; Fittings: ASME B16.18, cast copper alloy or 0. Prepare exposed, unfinished pipe, fittings, supports, and accessories ready for mn 21 = i>
<br /> galvanized housings and neoprene coated springs. protective liner; Metal Jacket Bands: 3/8 inch wide; 0.015 inch thick aluminum; ASME B16.22 wrought copper and bronze; Joints: ASTM B 32, alloy Sn95 solder. finish painting. L o
<br /> B. Spring Hanger: Springs: Minimum horizontal stiffness equal to 75 percent vertical Metal Jacket Bands: 3/8 inch wide; 0.010 inch thick stainless steel. B. Ductile Iron Pipe: AWWA C151/A21.51; Fittings: Ductile or gray iron, standard P. Paint all exterior above grade piping with a minimum of two coats of paint, color U_ U
<br /> stiffness, with working deflection between 0.3 and 0.6 of maximum deflection. D. Stainless Steel Jacket: ASTM A 666, Type 304 stainless steel; Thickness: 0.010 thickness; Joints: AWWA C111/A21.11, rubber gasket with 3/4 inch diameter rods. to match roof or wall surface to which it is attached; Copper pipe Apply vinyl etch cc
<br /> Color code springs for load carrying capacity; Housings: Incorporate neoprene inch; Finish: Smooth; Metal Jacket Bands: 3/8 inch wide; 0.010 inch thick 2.07 WATER PIPING, ABOVE GRADE primer immediately following cleaning. EXT 5.5A Alkyd: Vinyl Wash Primer MPI #80, rn
<br /> Ili
<br /> isolation pad meeting requirements for neoprene pad isolators or rubber hanger with stainless steel. A. Copper Tube: ASTM B 88 (ASTM B 88M), Type L (B), Drawn (H); Fittings: ASME Alkyd MPI #8, 9 or 94, Semi–gloss; Steel pipe: Apply alkyd metal primer immediately
<br /> threaded insert; Misalignment: Capable of 20 degree hanger rod misalignment; For B16.18, cast copper alloy or ASME B16.22, wrought copper and bronze; Fittings: following cleaning. EXT 5.1D Alkyd: Alkyd Metal Primer MPI #79, Alkyd MPI # 94, 111 Pacifica,Suite 280,Irvine,CA 92618
<br /> Exterior and Humid Areas: Hot dipped galvanized housings and neoprene coated PART 3 EXECUTION Cast iron, coated; Joints: ASTM B 32, alloy Sn95 solder; Joints: Grooved semi–gloss; Plastic pipe: Apply alkyd bonding primer immediately following P:949.553.1117 F:949.474.7056
<br /> springs. mechanical couplings. cleaning. EXT 6.86 Alkyd: Bonding Primer MPI #17 or 69, Alkyd MPI #8, 9 or 94.
<br /> C. Neoprene Pad Isolators: Rubber or neoprene waffle pads; Hardness: 30 durometer; 3.01 EXAMINATION 2.08 NATURAL GAS PIPING, ABOVE GRADE Q. Excavate, bedding and backfill shall be in accordance with applicable sections of
<br /> Thickness: Minimum 1/2 inch; Maximum Loading: 50 psi; Rib Height: Maximum 0.7 A. Verify that piping has been tested before applying insulation materials. A. Steel Pipe: ASTM A 53/A 53M Schedule 40 black; Fittings: 3" and larger shall be this Specification. ENGINEER STAMP ES
<br /> times width; Configuration: Single layer. B. Verify that surfaces are clean and dry, with foreign material removed. ASME B16.3, malleable iron, or ASTM A 234/A 234M, wrought steel welding type. R. Pipe vents from gas pressure reducing valves to outdoors and terminate in weather PRO�OY S�Oqq
<br /> D. Rubber Mount or Hanger: Molded rubber designed for 0.4 inch deflection with 3.02 INSTALLATION Threaded fittings may be used on piping 2 1/2 and smaller, except where noted on proof hood, unless of the ventless design and approved by the local jurisdiction �o y R SCy l
<br /> threaded insert. A. Install in accordance with manufacturer's instructions. the drawings or required by code to be welded; Joints: NFPA 54, threaded or welded and the local utility company regulates. q- p� 'Yy <!�
<br /> E. Glass Fiber Pads: Neoprene jacketed pre–compressed molded glass fiber. B. Install in accordance with NAIMA National Insulation Standards. to ASME 831.1. S. The use of sanitary tee fittings will not be permitted. Utilize wye fittings in /_ � 0
<br /> 2.04 SEISMIC RESTRAINTS C. Exposed Piping: Locate insulation and cover seams in least visible locations. B. Copper Tube: ASTM B 88 (ASTM B 88M), Type K (A) or L (B) annealed; Fittings: ASME lieu of tee fittings for all intersections of drainage piping. �' 0 r- %
<br /> A. Type: Non–directional and double acting unit consisting of interlocking steel D. Insulated pipes conveying fluids below ambient temperature: Insulate entire system B16.26, cast bronze; Joints: Flared. T. Provide sleeves when penetrating footings, masonry walls and floors. Seal and fire ca rn
<br /> members restrained b neoprene elements. including fittings, valves, unions, flanges, strainers, flexible connections, and 2.09 FLANGES, UNIONS, AND COUPLINGS stop pipe and sleeve penetrations to achieve fire resistance equivalent to fire No. M3329 m
<br /> Y P 9 9 9 PPP P q oWc
<br /> B. Elements: Replaceable neoprene, minimum of 0.75 inch thick with minimum 1/8 inch expansion joints. A. Unions for Pipe Sizes 3 Inches and Under: Ferrous pipe: Class 150 malleable iron separation required. All penetrations through footings and floors shall be sealed
<br /> air gap. E. Glass fiber insulated pipes conveying fluids below ambient temperature: Provide threaded unions; Copper tube and pipe: Class 150 bronze unions with soldered water tight.
<br /> C. Capacity: 4 times load assigned to mount groupings at 0.4 inch deflection. vapor barrier jackets, factory–applied or field–applied. Secure with self–sealing joints. U. Whereever piping is located within 1.5 inches of the nearest edge of studs, joists, FCHAN ICP �V,
<br /> D. Attachment Points and Fasteners: Capable of withstanding 3 times rated load longitudinal laps and butt strips with pressure sensitive adhesive. Secure with B. Flanges for Pipe Size Over 1 Inch: Ferrous pipe: Class 150 malleable iron rafters or similar members, provide minimum 0.062 inch thick steel protective qT �
<br /> capacity of seismic snubber. outward clinch expanding staples and vapor barrier mastic; Insulate fittings, threaded or forged steel slip–on flanges; preformed neoprene gaskets; Copper tube shield plates extending 2 above and below the pipe being protected. Shield plates F OF CAS\F
<br /> joints, and valves with molded insulation of like material and thickness as and pipe: Class 150 slip–on bronze flanges; preformed neoprene gaskets. may be omitted on cast iron piping only.
<br /> PART 3 EXECUTION adjacent pipe. Finish with glass cloth and vapor barrier adhesive or PVC fitting C. Grooved and Shouldered Pipe End Couplings: Housing: Malleable iron clamps to V. Inserts: Provide inserts for placement in concrete formwork; Provide inserts for
<br /> covers. engage and lock, designed to permit some angular deflection, contraction, and suspending hangers from reinforced concrete slabs and sides of reinforced concrete Date. 03/24/2020
<br /> 3.01 INSTALLATION F. For hot piping conveying fluids 140 degrees F or less, do not insulate flanges and expansion; steel bolts, nuts, and washers; galvanized for galvanized pipe; Sealing beams; Provide hooked rod to concrete reinforcement section for inserts carrying
<br /> A. Install in accordance with manufacturer's instructions. unions at equipment, but bevel and seal ends of insulation. gasket: "C" shape composition sealing gasket. pipe over 4 inches; Where concrete slabs form finished ceiling, locate inserts
<br /> B. Prior to making piping connections to equipment with operating weights G. For hot piping conveying fluids over 140 degrees F, insulate flanges and unions at D. Dielectric Connections: Union with galvanized or plated steel threaded end, copper flush with slab surface; Where inserts are omitted, drill through concrete slab
<br /> substantially different from installed weights, block up equipment with temporary equipment. solder end, water impervious isolation barrier. from below and provide through–bolt with recessed square steel plate and nut
<br /> shims to final height. When full load is applied, adjust isolators to load to H. Glass fiber insulated pipes conveying fluids above ambient temperature: Provide 2.10 PIPE HANGERS AND SUPPORTS recessed into and grouted flush with slab.
<br /> allow shim removal. standard jackets, with or without vapor barrier, factory–applied or field–applied. A. Plumbing Piping – Drain, Waste, and Vent: Conform to MSS SP-58; Hangers for Pipe W. Pipe Hangers and Supports: Install in accordance with ASME B31.9, ASTM F 708, and
<br /> C. Support piping connections to equipment mounted on isolators using isolators or Secure with self–sealing longitudinal laps and butt strips with pressure sensitive Sizes 1/2 Inch to 1-1/2 Inches: Malleable iron, adjustable swivel, split ring; MSS SP-89; Support horizontal piping as scheduled; Install hangers to provide
<br /> resilient hangers to nearest flexible pipe connector. adhesive. Secure with outward clinch expanding staples; Insulate fittings, joints, Hangers for Pipe Sizes 2 Inches and Over: Carbon steel, adjustable, clevis; minimum 1/2 inch space between finished covering and adjacent work; Place hangers
<br /> D. Provide flexible connections on all piping connections to equipment. and valves with insulation of like material and thickness as adjoining pipe. Multiple or Trapeze Hangers: Steel channels with welded spacers and hanger rods; within 12 inches of each horizontal elbow; Use hangers with 1-1/2 inch minimum
<br /> E. Selection of type, thickness and deflection of vibration isolation shall be by the Finish with glass cloth and adhesive or PVC fitting covers. Wall Support for Pipe Sizes to 3 Inches: Cast iron hook; Wall Support for Pipe vertical adjustment. Design hangers for pipe movement without disengagement of
<br /> vibration control manufacturer based on the specific equipment type and size, as I. Inserts and Shields: Application: Piping 2 inches diameter or larger; Shields: Sizes 4 Inches and Over: Welded steel bracket and wrought steel clamp; Vertical supported pipe; Support vertical piping at every other floor. Support riser piping
<br /> scheduled on the Drawings and indicated below. Galvanized steel between pipe hangers or pipe hanger rolls and inserts; Insert Support: Steel riser clamp; Floor Support: Cast iron adjustable pipe saddle, lock independently of connected horizontal piping; Where several pipes can be installed
<br /> F. Provide seismic snubbers for all equipment and piping mounted on isolators location: Between support shield and piping and under the finish jacket; Insert nut, nipple, floor flange, and concrete pier or steel support; Copper Pipe Support: in parallel and at same elevation, provide multiple or trapeze hangers; Provide
<br /> configuration: Minimum 6 inches long, of same thickness and contour as adjoining Carbon steel ring, adjustable, copper plated. copper plated hangers and supports for copper piping; Prime coat exposed steel 0
<br /> END OF SECTION insulation; may be factory fabricated; Insert material: Hydrous calcium silicate B. Plumbing Piping – Water and Gas: Conform to MSS SP-58; Hangers for Pipe Sizes 1/2 hangers and supports. Hangers and supports located in crawl spaces, pipe shafts, W N
<br /> insulation or other heavy density insulating material suitable for the planned Inch to 1-1/2 Inches: Malleable iron, adjustable swivel, split ring; Hangers for and suspended ceiling spaces are not considered exposed; Provide hangers adjacent J .
<br /> SECTION 220595 – FIRE STOPPING FOR PLUMBING SYSTEMS temperature range. Cold Pipe Sizes 2 Inches and Over: Carbon steel, adjustable, clevis; Hangers for to motor driven equipment with vibration isolation; Support cast iron drainageLO
<br /> /�
<br /> J. Continue insulation through walls, sleeves, pipe hangers, and other pipe Hot Pipe Sizes 2 Inches to 4 Inches: Carbon steel, adjustable, clevis; Hangers for piping at every joint. 0– \w\ M
<br /> PART 1 GENERAL penetrations. Finish at supports, protrusions, and interruptions. At fire Hot Pipe Sizes 6 Inches and Over: Adjustable steel yoke, cast iron pipe roll, 3.04 APPLICATION /
<br /> separations, fire stop penetrations to meet local code requirements. double hanger; Multiple or Trapeze Hangers: Steel channels with welded supports or A. Install unions downstream of valves and at equipment or apparatus connections. < < <
<br /> 1.01 SECTION INCLUDES K. Pipe Exposed in Finished Spaces (less than 10 feet above finished floor): Finish spacers and hanger rods; Multiple or Trapeze Hangers for Hot Pipe Sizes 6 Inches B. Install ball or butterfly valves for shut–off and to isolate equipment, part of 2 U) U
<br /> A. Firestopping materials; Firestopping of all penetrations and interruptions to fire with Aluminum, Stainless Steel, ABS or PVC jacket and fitting covers. and Over: Steel channels with welded supports or spacers and hanger rods, cast systems, or vertical risers. U) U
<br /> rated assemblies, whether indicated on Drawings or not, and other openings iron roll; Wall Support for Pipe Sizes to 3 Inches: Cast iron hook; Wall Support C. Install globe, ball, or butterfly valves for throttling, bypass, or manual flow W — z
<br /> indicated. 3.03 SCHEDULES for Pipe Sizes 4 Inches and Over: Welded steel bracket and wrought steel clamp; control services. Q LL
<br /> A. The Contractor may use any of the following insulating materials, at his option, Wall Support for Hot Pipe Sizes 6 Inches and Over: Welded steel bracket and D. Provide lug end butterfly valves adjacent to equipment when provided to isolate — O
<br /> PART 2 PRODUCTS provided the selected material meets with the approval of all State, local wrought steel clamp with adjustable steel yoke and cast iron pipe roll; Vertical equipment. Q U 0 U
<br /> authorities and utility company requirements. Verification of compliance of the Support: Steel riser clamp; Floor Support for Cold Pipe: Cast iron adjustable E. Provide spring loaded check valves on discharge of water pumps. Z Q Q
<br /> 2.01 FIRESTOPPING ASSEMBLIES selected insulating material and thickness with all State and local codes and pipe saddle, lock nut, nipple, floor flange, and concrete pier or steel support; F. Provide plug or gas service rated ball valves in natural gas systems for shut–off 1-- U. 1--
<br /> A. Firestopping: Any material meeting requirements; Fire Ratings: Use any system utility company requirements is the sole responsibility of the installing Floor Support for Hot Pipe Sizes to 4 Inches: Cast iron adjustable pipe saddle, service. L) b 0– � 1
<br /> listed by UL or FM or tested in accordance with ASTM E 814 or ASTM E 119 that has F Contractor. locknut, nipple, floor flange, and concrete pier or steel support; Floor Support G. Provide plug or gas service rated ball valves in propane gas systems for shut–off W ( 1 W O VO
<br /> Rating equal to fire rating of penetrated assembly and minimum T Rating Equal to F B. Plumbing Systems: for Hot Pipe Sizes 6 Inches and Over: Adjustable cast iron pipe roll and stand, service. v
<br /> Rating and that meets all other specified requirements. 1. Domestic Hot and Tempered Water Supply and Recirculation: steel screws, and concrete pier or steel support; Copper Pipe Support: Carbon H. Provide automatic flow controls valves in water recirculating systems where 0 Q 0 V-
<br /> 2.02 MATERIALS a. Glass Fiber Insulation: All Pipe: Thickness: 1 inch. steel ring, adjustable, copper plated. indicated. 0 � CO
<br /> A. Manufacturers: A/D Fire Protection Systems Inc; 3M Fire Protection Products; b. Flexible Elastomeric Cellular Foam Insulation: Pipe Size Range: First 2.11 GATE VALVES (Exterior Utility Service Only) I. Provide spring loaded check valves when located on the discharge of pumps. r U)
<br /> Specified Technologies, Inc. 8 feet of pipe from fixture, up to 1 1/4 inch: Thickness: 1/2 inch.; A. Manufacturers: Conbraco Industries; Nibco, Inc; Milwaukee Valve Company. 3.05 TOLERANCES
<br /> B. Elastomeric Silicone Firestopping: Single or multiple component silicone All Other Pipe: Thickness: 1 inch. B. Up To and Including 3 Inches: MSS SP-80, Class 125, bronze body, bronze trim, A. Interior Drainage Piping: Establish invert elevations within 1/2 inch vertically
<br /> elastomeric compound and compatible silicone sealant; conforming to the following: 2. Domestic Cold Water: rising stem, handwheel, inside screw, solid wedge disc, solder or threaded ends. of location indicated and slope to drain at minimum of 1/4 inch per foot slope, STORE #: 5470
<br /> Durability and Longevity. Permanent; Color: Manufacturers standard color. a. Glass Fiber Insulation: Pipe Size Range: All Sizes; Thickness: 1/2 Provide extension to grade and valve box per local jurisdiction and utility company unless noted otherwise on the Drawings.
<br /> C. Foam Firestoppping: Single or multiple component foam compound; conforming to the inch. standards. Post–indicator type were used for fire protection service or when B. Exterior Drainage Piping: Establish invert elevations within 1/2 inch vertically of PROJECT#: 03030-052
<br /> following: Durability and Longevity. Permanent; Color: Manufacturer's standard b. Flexible Elastomeric Cellular Foam Insulation: Pipe Size Range: All indicated on the Drawings. location indicated and slope to drain at a minimum of 1% grade, unless noted
<br /> color. Sizes; Thickness: 1/2 inch. C. 2 Inches and Larger: MSS SP-70, Class 125, iron body, bronze trim, outside screw otherwise on the Drawings. Verify all invert elevations prior to commencing work. CASEWORK CONCEPT: CORE
<br /> D. Fibered Compound Firestopping: Formulated compound mixed with incombustible E. Cooling Systems: and yoke, handwheel, solid wedge disc, flanged ends. Provide extension to grade C. Water Piping: Slope at minimum of 1/32 inch per foot and arrange to drain at low ISSUE DATE: CHECKSET2-10-20
<br /> non–asbestos fibers; conforming to the following: Durability and Longevity: 1. Cold Condensate Drains: and valve box per local jurisdiction and utility company standards. Post–indicator points.
<br /> Permanent; Color: Manufacturer's standard color. a. Glass Fiber Insulation: Pipe Size Range: All Sizes; Thickness: 1/2 type were used for fire protection service or when indicated on the Drawings. 3.06 DISINFECTION OF DOMESTIC WATER PIPING SYSTEM PROGRAM MANAGER: M. DBREBIKA
<br /> E. Fiber Packing Material: Mineral or ceramic fiber packing insulation; conforming to inch. 2.12 BALL VALVES A. Prior to starting work, verify system is complete, flushed and clean. STORE DESIGNER: M. DBREBIKA
<br /> the following: Durability and Longevity. Permanent. b. Flexible Elastomeric Cellular Foam Insulation: Pipe Size Range: All A. Manufacturers: Conbraco Industries; Nibco, Inc; Milwaukee Valve Company. B. Ensure Ph of water to be treated is between 7.4 and 7.6 by adding alkali (caustic
<br /> F. Firestop Devices: Mechanical device with incombustible or silicone elastomer Sizes; Thickness: 1/2 inch. B. Construction, 4 Inches and Smaller: MSS SP-110, Class 150, 400 psi CWP, bronze, soda or soda ash) or acid (hydrochloric). LEED®AP: N/A
<br /> filler and sheet stainless steel jacket, collar, and flanged stops; conforming to two piece body, chrome plated brass ball, regular port, teflon seats and stuffing C. Inject disinfectant, free chlorine in liquid, powder, tablet or gas form, CHECKED BY: A. FELDMAN
<br /> the following: Durability and Longevity. Permanent; suitable for pedestrian END OF SECTION box ring, blow–out proof stem, lever handle, solder or threaded ends. throughout system to obtain 50 to 80 mg/L residual.
<br /> traffic or vehicular traffic where necessary. 2.13 BUTTERFLY VALVES D. Bleed water from outlets to ensure distribution and test for disinfectant residual MCG PROJECT#: 18531
<br /> G. Firestop Pillows: Formed mineral fiber pillows; conforming to the following: SECTION 220720 – PIPING SAFETY COVERS A. Manufacturers: Hammond Valve; Crane Co; Milwaukee Valve Company. at minimum 15 percent of outlets.
<br /> Durability and Longevity. Permanent. B. Construction 1-1/2 Inches and Larger: MSS SP-67, 200 psi CWP, cast or ductile iron E. Maintain disinfectant in system for 24 hours. MCG PROD. MANAGER: C. LEE
<br /> H. Primers, Sleeves, Forms, and Accessories: Type required for tested assembly PART 1 GENERAL body, nickel–plated ductile iron disc, resilient replaceable EPDM seat, wafer, lug, F. If final disinfectant residual tests less than 25 mg/L, repeat treatment. MCG PROD. SPECIALIST: S.PARK
<br /> design. or grooved ends, extended neck, 10 position lever handle. G. Flush disinfectant from system until residual equal to that of incoming water or
<br /> 1.01 SECTION INCLUDES C. Provide gear operators for valves 8 inches and larger, and chain–wheel operators 1.0 mg/L.
<br /> PART 3 EXECUTION A. Piping Safety Covers. for valves mounted over 8 feet above floor. H. Take samples no sooner than 24 hours after flushing, from 10 percent of outlets and Revision Schedule
<br /> 2.14 FLOW CONTROLS from water entry, and analyze in accordance with AWWA C651.
<br /> 3.01 EXAMINATION PART 2 PRODUCTS A. Manufacturers: ITT Bell & Gossett; Griswold Controls; Taco, Inc. 3.07 SERVICE CONNECTIONS
<br /> A. Verify openings are ready to receive the work of this section. B. Construction: Class 125, Brass or bronze body with union on inlet, temperature and A. Provide new gas services complete with gas meter and regulators. Gas service Rev Date By Description
<br /> 3.02 PREPARATION 2.01 MANUFACTURERS pressure test plug on inlet and outlet. distribution piping shall have initial minimum pressure as indicated on the
<br /> A. Clean substrate surfaces of dirt, dust, grease, oil, loose material, or other A. Acceptable Manufacturer: Truebro, Inc. C. Calibration: Automatically control flow within 5 percent of selected rating, over drawings. Provide appropriately sized regulators on each line serving gas
<br /> matter which may affect bond of firestopping material. 2.02 PIPING INSULATION ACCESSORIES operating pressure range of 10 times minimum pressure required for control, maximum appliances, sized in accordance with the manufacturers recommendations based on the
<br /> B. Install backing materials to arrest liquid material leakage. A. Provide products that comp) with the following: Americans With Disabilities Act minimum pressure 3.5 psi. sizing parameters indicated on the Drawings. The entire gas service and piping
<br /> 3.03 INSTALLATION (ADA), Article 4.19.4; ANSI7CC A117.1, American National Standard for Accessible 2.15 SWING CHECK VALVES installation shall comply with the local jurisdiction and the regulations of the
<br /> A. Install materials in manner described in fire test report and in accordance with Buildings and Facilities; Requirements of applicable building code. A. Manufacturers: Hammond Valve; Nibco, Inc; Milwaukee Valve Company. serving utility.
<br /> manufacturer's instructions, completely closing openings. B. Piping Safety Covers: Truebro Lav–Guard; Characteristics: Three–piece molded B. Up to 3 Inches: MSS SP-80, Class 125, bronze body and cap, bronze swing disc with 3.08 SCHEDULES
<br /> B. Do not cover installed firestopping until inspected by authority having assembly, minimum 1/8 inch wall thickness, with internal ribs to provide air space rubber seat, solder or threaded ends. A. Pipe Hanger Spacing:
<br /> jurisdiction. between piping and piping insulation jacket, molded to receive manufacturer's C. Over 2 Inches: MSS SP-71, Class 125, iron body, bronze swing disc, renewable disc 1. Metal Piping: SHEET TITLE:
<br /> C. Install labeling required by code. snap–clip fasteners; Vinyl Material: Impact–resistant and stain–resistant molded seal and seat, flanged or grooved ends. a. Pipe size: 1/2 inches to 1-1/4 inches: Maximum hanger spacing: 6.5 PLUMBING
<br /> 3.04 CLEANING AND PROTECTION closed–cell anti–microbial vinyl compound, UV–stable, non–fading, non yellowing; 2.16 WATER PRESSURE REDUCING VALVES ft; Hanger rod diameter: 3/8 inches.
<br /> A. Clean adjacent surfaces of Firestopping materials. having the following performance characteristics: Burning Characteristics: 0 A. Manufacturers: Amtrol Inc; Cla–Val Co; Watts Regulator Company. b. Pipe size: 1-1/2 inches to 2 inches: Maximum hanger spacing: 10 ft;
<br /> seconds Average Time of Burning (ATB), 0 mm Area of Burning (AEB), when tested in B. Up to 2 Inches: MSS SP-80, bronze body, stainless steel and thermoplastic internal Hanger rod diameter: 3/8 inch. SPECIFICATIONS
<br /> END OF SECTION accordance with ASTM D 635; Thermal Conductivity. K–value 1.17, when tested in parts, fabric reinforced diaphragm, strainer, threaded single union ends. C. Pipe size: 2-1/2 inches to 3 inches: Maximum hanger spacing: 10 ft; AW�Fnnkla_,
<br /> accordance with ASTM C 177; Indentation Hardness: 60, minimum, when tested in C. Over 2 Inches: MSS SP-85, cast iron body, bronze fitted, elastomeric diaphragm and Hanger rod diameter: 1/2 inch. Sehnaekel SCALE:AS SHOWN
<br /> SECTION 220719 – PLUMBING PIPING INSULATION accordance with ASTM D 2240, using Type A durometer; Trap Assembly Cover: seat disc, flanged. d. Pipe size: 4 inches to 6 inches: Maximum hanger spacing: 10 ft;
<br /> Three–piece assembly, with removable clean–out nut enclosure; Angle Stop Covers: 2.17 RELIEF VALVES Hanger rod diameter: 5/8 inch. mS engineers,
<br /> PART 1 GENERAL Formed with hinged cap for access to valve without requiring cover removal; A. Pressure Relief: Manufacturers: Cla–Val Co; Henry Technologies; Watts Regulator 2. Plastic Piping: NewYorkaohaaLasAngelmHonddu
<br /> maSHEET NUMBER:
<br /> Configurations: In accordance with manufacturers product data for project piping Company, AGA Z21.22 certified, bronze body, teflon seat, steel stem and springs, a. Pipe size: 1/2 inches to 6 inches: Maximum hanger spacing: 6 ft; 800-581-0963 wwwschnadwLcom
<br /> 1.01 SECTION INCLUDES configurations indicated on Drawings; Color: China White, gloss finish; paintable; automatic, direct pressure actuated. Hanger rod diameter: 3/8 inch. P-0002
<br /> A. Plumbing piping insulation; Domestic hot and tempered water piping; Domestic cold Fasteners: Manufacturers standard re–usable snap–clip fasteners; wire–tie B. Temperature and Pressure Relief: Manufacturers: Cla–Val Co; Henry Technologies;
<br /> 80 South Lake Avenue, Suite 640 Pasadena, CA 91101 L
<br /> SE JOBQ: 181189
<br />
|