WORK PLANS - Laserfiche WebLink

Home Browse Search

2 3 4 5 a _L3 0 m 0 N O N L FIXTURE AND SPECIALTIES PLUMBING SCHEDULE ( SEE COMPREHENSIVE EQUIPMENT SCHEDULE ON SHEET EQ 2) 0 U MARK DESCRIPTION SUPPLIED BY INSTALLED BY MANUFACTURER MODEL # DESCRIPTION CONNECTIONS REMARKS WASTE VENT H.W. C.W. P-4 LAVATORY MILLWORK VENDOR G.C. PLUMBER CORIAN 8254-GLACIER WHITE RECTANGULAR UNDER-MOUNT LAVATORY 1-1/4" 1-1/4" 1/2" 1/2" -- FAUCET G.C. PLUMBER G.C. PLUMBER SLOAN EAF-275-SOL-ISM-SF-0.5GPM-AER-IR-IQ-FCT OPTIMA SENSOR FAUCET-SOLAR POWER SUPPLY, INTEGRATED SIDE MIXER, BRUSHED STAINLESS FINISH, 0.5GPM, AERATED SPRAY, INFRARED SENSOR, OPTIMA SOLAR POWERED DECK-MOUNTED MID BODY FAUCET. - - - - -- SUPPLIES G.C. PLUMBER G.C. PLUMBER -- -- CHROME PLATED ANGLE STOPS WITH WHEEL HANDLE, CHROME PLATED FLEXIBLE BRASS RISER, INSULATE ALL EXPOSED WATER LINES AND VALVES. - - - - -- WASTE G.C. PLUMBER G.C. PLUMBER SPEAKMAN S-3440 GRID DRAIN STRAINER, 1-1/4" TAILPIECE, 1-1/4" 17 GAUGE CHROME PLATED ADJUSTABLE BRASS P-TRAP WITH CLEANOUT PLUG, 1-1/4" CHROME PLATED BRASS WASTE TO WALL. - - - - -- H11 ENGINEERS Engineering Firm : F-21834 GHC Engineers, LLC GENERAL NOTES PIPING MATERIALS LEGEND 14901 Quorum Dr, Ste 300Dallas, Texas 75254 SEWERBELOW GRADE SCHEDULE 40 PVC Office: 972-239-8884 1. VERIFY EXACT LOCATIONS, ELEVATIONS AND CHARACTERISTICS OF UTILITIES AND PIPING BEFORE gclaussen@ghcengineers.com COMMENCEMENT OF WORK, AND IMMEDIATELY NOTIFY THE ARCHITECT OF ANY DISCREPANCIES. WASTE VENT ABOVE GRADE SCHEDULE 40 PVC 2. OBTAIN EXACT LOCATIONS AND MOUNTING HEIGHTS OF PLUMBING FIXTURES AND KITCHEN EQUIPMENT COLD & HOT WATER (ABOVE GROUND) TYPE 'L' COPPER OR PEX Project#G210418.001 FROM ARCHITECTURAL AND KITCHEN EQUIPMENT DRAWINGS. COLD WATER (BURIED) TYPE 'K' COPPER OR PEX CERTIFICATION 3. CONTRACTOR SHALL MAKE ALL ARRANGEMENTS WITH UTILITY COMPANIES FOR SERVICE AND CONNECTIONS AND SHALL PAY FOR ALL PERMITS. FEES, CHARGES AND METERS. GAS (ON ROOF & INSIDE BUILDING) SCHEDULE 40 BLACK IRON 4. PLUMBING CONTRACTOR SHALL VERIFY INSTALLATION REQUIREMENTS FOR FLOOR SINKS AND FLOOR CONDENSATE DRAIN TYPE 'M' COPPER DRAINS. THE GOVERNING AUTHORITY HAVING JURISDICTION MAY REQUIRE THE FOLLOWING: FLOOR SINKS INDIRECT DRAIN (INSIDE BUILDING) DWV COPPER QRpFESS/p MAY BE REQUIRED TO BE INSTALLED WITH THE RIM RAISED ABOVE THE FINISHED FLOOR. FLOOR DRAINS O �9l ED MAY NEED TO BE RECESSED WITH THE FLOOR SLOPED TO THE DRAIN. THE PLUMBING CONTRACTOR NOTE: REFER TO PROJECT SPECIFICATION MANUAL. X00 R� SHALL BE RESPONSIBLE FOR OBTAINING THIS INFORMATION AND INSTALLING THESE ITEMS AS REQUIRED 2 BY CODE. w 4274 m 5. INSTALL ALL PLUMBING TO AVOID INTERFERENCE WITH ELECTRICAL AND MECHANICAL EQUIPMENT AND * EXp 12.31.22 STRUCTURAL FRAMING. NO WATER OR DRAIN LINES PERMITTED OVER OR UNDER ELECTRICAL PANELS. ENSURE THAT ALL WATER LINES INSIDE WALLS ARE ADEQUATELY SECURED. PIPE HANGER SPACING SCHEDULE (9 �FCHAWr-P�. .P 6. PROVIDE TRAPS, STOPS, GATE VALVES, GAS COCKS, WATER HAMMER ARRESTERS, VACUUM BREAKERS ON gTFOFOq�\FO�� THREADED FAUCETS, WALL CLEANOUTS, CLEANOUT COVERS, FLEX CONNECTIONS, SHUT-OFF VALVES AND MAXIMUM HORIZONTAL MAXIMUM VERTICAL INDIRECT WASTE TO AN APPROVED RECEPTOR AND ALL NECESSARY TRIM FOR A COMPLETELY INSTALLED PIPING MATERIAL SPACING (FEET) SPACING (FEET) 0 4 .2 6 .21 & CONNECTED PLUMBING SYSTEM. 7. RECORD ON AS-BUILT DRAWINGS, ALL SIZES, LOCATIONS. INVERTS AND MATERIALS OF EXISTING PIPES SCHEDULE 40 PVC 4 1Q1 THAT ARE ENCOUNTERED AND NEW PIPES INSTALLED DURING THE COURSE OF THE PROJECT DELIVER SCHEDULE 40 BLACK IRON 12 15 AS—BUILTS TO THE CONSTRUCTION MANAGER AT THE END OF THE PROJECT. PEX 2.67 101 8. ALL WORK SHALL BE DONE IN ACCORDANCE WITH ALL LOCAL AND FEDERAL CODES, RULES AND COPPER OR COPPER—ALLOY PIPE 12 10 REGISTRATION NUMBER REGULATIONS GOVERNING THIS PROJECT. C017261 9. UPON COMPLETION OF JOB, INSPECT ALL EXPOSED PORTIONS OF THE PLUMBING INSTALLATIONS AND a. THE MAXIMUM HORIZONTAL SPACING OF CAST—IRON PIPE HANGERS SHALL BE INCREASED TO 10 FEET COMPLETELY REMOVE ALL EXPOSED LABELS, SOIL, MARKINGS, AND FOREIGN MATERIAL EXCEPT PRODUCT WHERE 10—FOOT LENGTHS OF PIPE ARE INSTALLED. EXP DATE LABELS AND THOSE REQUIRED BY LAW. b. FOR SIZES 2 INCHES AND SMALLER, A GUIDE SHALL BE INSTALLED MIDWAY BETWEEN REQUIRED VERTICAL 10.TERMINATE ALL INDIRECT WASTE LINES ABOVE FLOOR SINK WITH 1" (MIN.) AIR GAP. ALL INDIRECT SUPPORTS. SUCH GUIDES SHALL PREVENT PIPE MOVEMENT IN A DIRECTION PERPENDICULAR TO THE AXIS OF 12.31.22 WASTE PIPING MUST BE HARD PIPED, COPPER ONLY. NO P.V.C. ALLOWED. THE PIPE. PROJECT NUMBER II.PROVIDE FLEXIBLE GAS CONNECTIONS TO WATER HEATER AND COOKING EQUIPMENT. PROVIDE RIGID FROM THE INTERNATIONAL PLUMBING CODE TABLE 308.5 200772 GAS CONNECTIONS TO ALL OTHER EQUIPMENT AND APPLIANCES AND WHERE LOCAL JURISDICTION PROHIBITS THE USE OF FLEXIBLE CONNECTIONS. 12.VFRIFY ALL EQUIPMENT AND APPLIANCE CONNECTION SIZES PRIOR TO MAKING FINAL CONNECTION. REDUCE BRANCH PIPE SIZING JUST PRIOR TO CONNECTION TO UNIT. W U) 0_ O (D J J LL Z O N O N J 0Q 0 p 10�JUw _JJa w J V U Q Q O Q o H z z Cn (-0 W w J WN ~ w Q CO LL w 0 LL J W M O W w .a MU �& 0 9 D 3 GLENLAKE PARKWAY NE BWW DESIGN TEAM ATLANTA, GA 30328 PHONE 678.514.4100 N W O � N p N 0 W Z) �U) /1 11 z `J O_ Z ~ a_ U) W W W W 0 a- 0 O LL W Z) U) Z - N CO It LO CO Drawing Title PLUMBING SCHEDULES & RISERS N ® P401