WORK PLANS - Laserfiche WebLink

Home Browse Search

le-. to C ❑ F C floor dimension plan notes: t V 1. content included on this exhibit is limited to the architectural scope only- refer to structural exhibits for additional information-structural is O not to be implied or otherwise assumed from this exhibit Q 2. all dimensions to new construction are to face of framing unless Q6 otherwise noted M 3. all dimensions to existing construction are to face of finish unless X otherwise noted Q D5 4. grid lines are located at the center of walls and/or columns unless Q A3.1.0 otherwise noted 5. although not required in all cases, it is the architect's standard to CV utilize 518"type"X"gypsum wall board unless otherwise noted _ ==EJ 6. moisture resistant gypsum wall board or cement backer board shall be used at all wet locations -0 7. contractor to verify(E) conditions and dimensions prior to construction (1) and notify architect if a conflict exists p u I I arc teetu e, inc. (1) l / 8. contractor to coordinate with kitchen equipment consultant for location 3 7 5 2 v i n ey a n d r o a d -0 of soda and bar line chase locations w.o. -pvc sleeve penetration r o s e v i I 1 e , c a 3 5 7 4 7 — I installed with upper lip at 6"a.f.f. unless otherwise noted by kitchen 9 1 6 7 4 0 3 7 2 6 � consultant www . pullarchitect L re . com 9. see food service drawings and plumbing drawings for locations of floor I (E) sinks and floor drains U , 10. refer to accessibility sheets A-0.3.0&A-0.4.0 for additional information with regard to accessibility related issues 11. mechanical, electrical, plumbing, structural, interior finishes, data, and i E other information referencing other disciplines may be included for odesign intent and/or reference- refer to specific discipline's exhibit for Q o more information-contractor shall notify architect if a conflict of information exists N o I 12. all concealed combustible spaces shall be draft stopped at 10'-0" intervals both horizontal and vertical or shall be sprinkled in I accordance with NFPA standards IYJ 13. refer to kitchen equipment consultant drawings for equipment r specification, clearances, rough in openings etc. , N � ON I - MICHA GIVK N ' f.o. framing 0 G i72 RfNEWAE 0 0 3-T � CL � ❑ O O ITI t� I These drawings,designs,sketches and ideas,a well as any p w and all electronic files are the sole and exclusive property of"pull _ - architecture", These plans were created and dei eloped by and UCV) C for the architects work. Nothing contained or re resented on j Q C _ � W these documents shall be used by any person,fi or other to E entity for any purpose without the prior written c sent of an f + C a) U authorized and recognized representative of"put architecture". -N N � U N S!3 The work contained on these drawings and doc encs applies U L I to this project exclusively,and is not to be used r other projects r to E e U A-_ 41 w Q whether related,implied or future- 1V i A3.1.0 F I l date: i revisions: by: I UO keynotes tenant provided die wall-contractor installed 1 anchored per � structural and located to meet minimum clearance requirements as O provided on this sheet ' 36" min. clear , , I �r � U .E note: project: Sunset S eets 6649 Embarcadero Dr., Ste 103 Stockton, CA 95219 developed by: Pellarin En erprises 1520 Main Street Redwood City, CA 94063 C p. 2 9.951.1551 www.rellarin.com project no.: PA20 21_0001 date: 0 4.12.2021 designed by: C 4 E drawn by: Mchecked by: floor dimension tan o �- - A8 p sheet: 1121, = 11.0" Q too Al m2ml