INSTALL_2001 - Laserfiche WebLink

Home Browse Search

island Installation Metal Island Forms A typical installation application for dispenser sumps/pans is to mount them Each dispenser sump/pan is fitted with a full perimeter rigid frame which can inside a pre-engineered metal island form. It is important that the sump/pan be mounted to some type of support bar. Adjustable support bars are avail- be mounted in such a manner that the top of the outside strut is flush with the able with some types of pre-engineered metal island forms. Other island forms concrete surface of the finished island. The plastic rain lip should extend 1" may require additional field installed support bars. Refer to the details below above the concrete to prevent surface run-off from entering the sump. for additional information. Top Frame Support Under Frame Support Top Frame Support Fasten the sump/pans frame to two pieces of Set the sump/pans frame over two metal cross Existing concrete islands can be modified to lumber which will span across the top of the supports which span across the metal island accommodate the dispenser sump/pan by metal island form and secure the sump. form and secure the sump. enlarging the pipe access opening. Existing o,,Penser _ Opening I Sump Location Wood [— O O 4 Metal O O 2x4 supports J Supports Enlarged Opening N. Pipe/Conduit l :H: I Flexible Entry Boots GeoDuct Boots Flexible Entry Boots Conduit Entry Boots Stage II Entry Boots Installed in the sidewall Installed in the sidewail Installed in the bottom of Installed in the bottom of Installed in the bottom of of Dispenser Sumps to of Dispenser Sumps to Dispenser Pans to provide Dispenser Pans to provide Dispenser Pans to provide provide a liquid tight seal for provide a liquid tight seal for a liquid tight seal for all pipe a liquid tight seal for 3/4" a liquid tight seal for 1-1/2" all pipe and conduit entries. GeoDuct containment pipe entries and flexible isolation conduit pipe entries. to 1"Stage II pipe entries. and GeoFlex flexible pipe. tubes. For specific sizing,see chart below. Flexible Entry Boot Sizes Hole Saw Hole Saw Boot ID Size Size Part No. Boot ID Size Size Part No. .84" 1/2"Rigid Conduit 2-3/8" FEB-3050 2.37' 3"Standard Rigid Pipe 4-1/4" FEB-6300 1.05' 3/4'Rigid Conduit 2-3/8" FEB-3075 3.50' 3'Standard Rigid Pipe 4-1/4' FEB-6350• 1.32" 1"Rigid Conduit 2-3/8" FEB-3100 3.90" 3-1/2"Custom Pipe 5-1/2' FEB-7390 1.81" 1-1/2"Standard Rigid Pipe 2-3/8" FEB-3150 4.50' 4"Standard Rigid Pipe 5-1/2' FEB-7400 1.81" 1-1/2"GeoFlex Pipe 4-1/4" FEB-6150 4.50" 4"GeoDuct Conduit 5-1/2" GDB-7450' 2.37' 2"GeoFlex Pipe 4-1/4" GFB-6200 6.50 6"Standard Rigid Pipe Sabre Saw FEB-8600 2.37" 2"Standard Rigid Pipe 4-1/4" FEB-6200 4.50" Sump Access Boot 5-1/2" SAB-7400 These boots require a Split Reducer/Test Donut,sold separately. See below. Split Reducers/Test Donuts Part No. For all GeoDuct pipe entries,used to seal Boot=Description w/airstem wo/airstem the GeoDuct conduit to GeoFlex pipe. The 2" To seal 3"GeoDuct to 1-1/2"GeoFlex piping STD-3015 SRD-3015 donut is inserted into the appropriate size 2.5* To seal 3"GeoDuct to 2"GeoFlex piping WA SRD-3020 GeoDuct Boot and a band clamp secures a tight, leak-proof seal. Available with 2" To seal 4"GeoDuct to 1-1/2"GeoFlex piping STD-4015 SRD-4015 (STD series) or without (SRD series) 2.5' To seal 4'GeoDuct to 2"GeoFlex piping STD-4020 SRD-4020 airstem. See chart for exact specifications. (2)1.1" To seal 4"GeoDuct to two 3/4"GeoFlex lines STD-4077 SRD-4077