Laserfiche WebLink
Single Phase Duplex <br />This control panel must be installed and serviced by a licensed electri- <br />J cian in accordance with the National Electric Code NFPA-70, state and local <br />. electrical codes. <br />! Ali conduit running from the sump or tank to the control panel must be sealed <br />ELECTRICAL SHOCK HAZARD with conduit sealant to prevent moisture or gases from entering the panel. NEMA <br />Disconnect all pourer sources before 1 enclosures are for indoor use only, primarily to provide a degree of protection <br />servicing. Failure to do so could result against contact with enclosed equipment. Cable connectors are not required to be <br />in serious injury or death, liquid -tight in NEMA 1 enclosures. Do not use NEMA 1 enclosures if subjected <br />to rain, splashing water or hose -directed water. NEMA 4X enclosures are for <br />4 indoor or outdoor use, primarily to provide a degree of protection against corro- <br />sion, windblown dust and rain, splashing water and hose -directed water. Cable <br />connectors must be liquid -tight in NEMA 4X enclosures. <br />Warranty void if panel is modified. <br />Call factory with servicing questions: <br />(1-800-746-6287) <br />Manufactured by: <br />I, T11FI-11 I i <br />22656 County ltighway 6 AF P.O. Box 1708 <br />Detroit Lakes, N-Ainnesota. 56502 USA <br />1 -888 -DIAL -SSE (1-888-342-5753) <br />Phone: 218-817-1317 Iff lax: 218-847-4617 <br />E-mail: customer.servir-c-@sjerhonibus.corn <br />b1'ebsite: wNvNv.sjerhornbus.com <br />Ms-Phio ,buu <br />PNI017346C • Rev 1114 <br />Most Type 122 panels are designed to operate as three or four float systems. The <br />three float system is standard performing the common pump stop, lead pump start, <br />and lag pump start/high level alarm functions. The fourfloat system utilizes separate <br />floats for lag pump start and high level alarm. <br />NOTE: Options ordered may affect the number of floats and their functions. <br />Please reference the schematic provided with the control panel for proper <br />installation. <br />installation of Pleats <br />CAUTION: If control switch cables are not wired and mounted in the correct location, <br />the pump system will, not function properly. <br />WARNING: Turn off all power before installing floats in pump chamber. Failure to <br />do so could result in serious or fatal electrical shock. <br />1. Use Float label kit to identify and label cables on both float and stripped ends <br />(stop, lead, lag, alarm, etc.). See schematic for float options. <br />2. Deten-nine your normal operating level, as illustrated in Figures 1-2. <br />3. Mount float switches at appropriate levels as illustrated in Figures 3-5. Be <br />sure that floats have free range of motion without touching each other, or other <br />equipment in the basin. <br />If using the mounting clamp; follow steps 4-6. <br />4. Place the cord into the clamp as shown in Figure 5. <br />5. Locate the clamp at the desired activation level and secure the clamp to the <br />discharge pipe as shown in Figure 5. <br />NOTE: Edo not install cord under hose clamp - <br />6. Tighten the hose clamp using a screwdriver. Over tightening may result in <br />damage to the plastic ciarrlp. flake sure, the float cable is not allowed to touch <br />the excess hose clamp band during operation. <br />NOTE: All hose clamp components are made of 18-8 stainless steel material. <br />See your SPIE -Rhombus"' supplier for replacements, <br />