WORK PLANS - Laserfiche WebLink

Home Browse Search

RL-2DRIM-05-E4-R IM-05-E4-RGLD36A-135GLD36A-135GLD36A-135GLD36A-135 R10 15'-6"R SC1 SC7 SC6 SC4 SC7 SC5 SC9 SC8 A1 R R R10 A6 SC2 SC10 R 34'-9" A6 SC3 R01 SC11 S = 7/8" SR = 3/4" L = 1/2" R10 CU3CU4 CU4 BEER COOLER BEVERAGE COOLER A2 A3 A4 A5 R10 R10 S = 7/8" SR = 3/4" L = 1/2" S = 7/8" SR = 3/4" L = 1/2" S = 7/8" SR = 5/8" L = 1/2" S = 5/8" SR = 1/2" L = 1/2" S = 7/8" SR = 3/4" L = 1/2" R07 R07 R25 L L L L L L R26 R26 R26 R26 R26 R26 CU1CU1CU1CU1CU1CU11 1/4" = 1'-0" REFRIGERATION PIPING PLAN SYMBOLS KEYED NOTES GENERAL NOTES SYMBOL KEYED NOTE DESCRIPTION CASE ELECTRICAL ENTRY ELECTRICAL STUB-UP CASE REFRIGERATION CONNECTION REFRIGERATION STUB-UP CASE CONDENSATE HUB DRAIN RE: R5-4 COIL CONDENSATE TRENCH DRAIN WALK-IN BOX COIL DRAIN LINE RE: R5-4, R6-6 CONDENSATE DRAIN LINE DIRECTIONAL ARROW SYSTEM REFERENCE NUMBER REFRIGERATION CONDUIT RE: R5-2 6" OR 8" SCHEDULE 40 PVC. LIQUID LINE SOLENOID REVISION SYMBOL DEFROST TERMINATION SUCTION LINE LIQUID LINE SUCTION RISER ELECTRICAL REQUIREMENTS RE: R4 THERMOSTAT R10 R00 R08 S L SR L DT E E R R PIPING RISER 1. ALL STUB-UP DIMENSIONS ARE FROM OUTSIDE FACE OF EXTERIOR WALL OR CENTER OF COLUMN UNLESS OTHERWISE NOTED. REFRIGERATION CONTRACTOR TO VERIFY COLUMN LOCATION WITH R-1 SHEET. 2. ALL OVERHEAD REFRIGERATION LINES SHALL BE INSTALLED WHERE SHOWN ON PLANS. 3. REFRIGERATION LINES SHALL BE INSTALLED ABOVE BOTTOM OF ROOF STRUCTURE. AVOID CONFLICTS WITH SKYLIGHTS AND OTHER TRADES. COORDINATE INSTALLATION & LOCATION WITH GENERAL CONTRACTOR. 4. ALL CASES SHALL HAVE MANUFACTURERS RECOMMENDED AIR GAP. 5. RE: R3 SCHEDULE FOR SYSTEM & CASE INFORMATION. 6. RE: R2 FOR REFRIGERATION PIPING REQUIREMENTS. 7.REFRIGERATION CONTRACTOR TO FILL ALL OPENINGS THROUGH WALK-IN PANELS WITH FOAM INSULATION AFTER LINES ARE INSTALLED, INCLUDING REFRIGERANT PIPING, CONDENSATE DRAINS, CONDUIT, SPRINKLER LINES. R02 EQUIVALENT LENGTHEL R00 THERMOSTAT MOUNTED IN CASE BY CASE MANUFACTURER OR IN COOLER BOX BY REFRIGERATION CONTRACTOR. RE: R-4.1. R01 DEFROST AND TEMPERATURE CONTROL ACCOMPLISHED THROUGH LIQUID LINE SOLENOID AT CONDENSING UNIT. R02 COOLER DRAIN PIPING RE: R1, R5-6 R03 COOLER DRAIN PIPING TO TERMINATE AT EXTENDED TRENCH DRAIN. TRENCH DRAIN TO BE EXTENDED 12" TOWARD PIPING. R05 REFRIGERATION LINES FROM TOP OF COOLER BOX RUNNING UP TO THE ROOF, THEN OVERHEAD TO CONDENSING UNIT ON ROOFTOP. R07 REFRIGERATION LINES FROM CASE CONNECTION TO WALL OR COLUMN, THEN UP IN WALL OR COLUMN TO OVERHEAD, THEN OVERHEAD TO CONDENSING UNIT. R08 DEFROST TERMINATION KLIXON INSTALLED BY CASE MANUFACTURER. R10 LIQUID LINE SOLENOIDS AND ISOLATION VALVES SUPPLIED BY CONDENSING UNIT MANUFACTURER AND INSTALLED BY REFRIGERATION CONTRACTOR AT OR IN WALK IN COOLERS. SOLENOID POWER WIRES SHALL BE PROVIDED FROM LIQUID LINE SOLENOID VALVE TO REFRIGERATION CONDENSING UNIT SYSTEM BY ELECTRICAL CONTRACTOR. ELECTRICAL CONTRACTOR SHALL PROVIDE CONDUIT AND TERMINATE WIRE AT CONTROL MODULE AND SOLENOID. REFRIGERATION CONTRACTOR TO PROVE PERFORMANCE OF THE VALVES AND REFRIGERATION SYSTEM. RE: R-2 R12 REACH IN DOOR LIGHT AND ANTI-SWEAT POWER PROVIDED BY GENERAL CONTRACTOR. R19 COORDINATE LOCATION OF ENVIRONMENTAL CONTROL PANEL WITH ENERGY MANAGEMENT CONTRACTOR AND/OR AXIOM ENERGY SOLUTION. ELECTRICAL CONTRACTOR TO PROVIDE POWER AND COORDINATE WITH ENERGY MANAGEMENT CONTRACTOR. REFRIGERATION CONTRACTOR TO MOUNT REFRIGERATION CONTROL ENCLOSURE AS CLOSE TO ECP AS POSSIBLE. R20 KRACK MODEL ASHR9512ZFA ROOF MOUNTED CONDENSING UNIT PROVIDED BY OWNER RECEIVED, SET AND INSTALLED BY REFRIGERATION CONTRACTOR. LOCATION OF THE CONDENSING UNIT IS FOR REFERENCE ONLY EXACT LOCATION TO BE VERIFIED WITH AOR. RE: R6-10 R22 KRACK MODEL ASHR2460ZFA ROOF MOUNTED CONDENSING UNIT PROVIDED BY OWNER RECEIVED, SET AND INSTALLED BY REFRIGERATION CONTRACTOR. LOCATION OF THE CONDENSING UNIT IS FOR REFERENCE ONLY EXACT LOCATION TO BE VERIFIED WITH AOR. RE: R6-10 R23 ROOF PENETRATION AND PIPE HOOD BY GENERAL CONTRACTOR. RE: R5-3 R24 FRONT OF CONDENSING UNIT. R25 UNDERGROUND REFRIGERATION LINES TO BE PLACED IN PVC. RE:R5-2 R26 FOR CONTINUATION OF PIPING TO CONDENSING UNIT ON ROOF RE: R3-1 ELECTRICAL CONTRACTOR SHALL: 1. USE MATERIAL AND METHODS OF INSTALLATION THAT CONFORM TO ALL APPLICABLE CODES AND ORDINANCES. 2. ELECTRICAL CONTRACTOR TO RUN ALL POWER AND CONDUIT AS INDICATED IN THESE DRAWINGS AND ASSOCIATED SPECIFICATIONS. PLUMBING NOTES PLUMBING CONTRACTOR SHALL: 1.USE MATERIAL AND METHODS OF INSTALLATION THAT CONFORM TO ALL APPLICABLE CODES AND ORDINANCES. 2.FURNISH AND INSTALL ALL FLOOR DRAINS, GREASE TRAPS (AS REQUIRED), FAUCETS, HOT AND COLD WATER SUPPLY LINES, SHUT OFF VALVES, HOSE BIBS, AND RECESSED METAL ENCLOSURES. REFRIGERATION CONTRACTOR SHALL: 1.FURNISH AND INSTALL ALL CONDENSATE DRAIN LINES WITH APPROVED TRAPS FROM EACH CASE OR EVAPORATOR COIL TO DRAIN, UNLESS OTHERWISE SPECIFIED. ELECTRICAL NOTES REGISTEREDP R O F E S SION A L E NGI NEERJAR E D H .MIL L E RST A TEOF C A L I F O R N IAM ECHA N I C A LProject:21STAN01Phone: 208.288.2181 SHEET TITLE SHEET NO. SUBMITTAL CAD SAVED NAME: PROJECT NO. DRAWN BY: CHECKED BY: OWNER: 21.03.19 BUILDING DEPT: 21.05.14 O.T.B.: DATES REVISIONS: DATE#REVISION BY SAFEWAY FUEL CENTER #005519533 S. MOUNTAIN HOUSE PKWY.MOUNTAIN HOUSE, CA 953812007730004 --www.stantec.comTEL. 1383 North McDowell Blvd. Suite 250Petaluma, CA 94954707.765.1660Architecture Inc.- 05 / 17 / 2021 R2 REFRIGERATION PIPING PLAN