Laserfiche WebLink
OPW NO . 1 -2100 SERIES GRADE a non -hardening , gasoline resistant pipe thread seal <br /> LEVEL SPILL CONTAINER compound . Use only factory made nipples . Nipples <br /> INSTALLATION INSTRUCTIONS : must be cut square and deburred . Torque to 125 ft- <br /> lbs min . to 250 ftdbs max. (4 " NPT) . Torque value is <br /> Step1 . based on rotation at the center of pipe . For standard <br /> Per California SB-989 , all metal must be protected cover models install adaptor and dust cap . For <br /> from direct contact with the elements . Coat stainless sealable cover ( 1 SC ) models , install a standard 4 " <br /> steel band clamps with the following approved pipe cap to support adjustment system . (Adaptor and <br /> coatings . OPW SL- 1100 , 3M Underseal 08883 or dust cap must be installed in sealable cover ( SC) <br /> Polyguard Mastic CA-9 . Only the threaded hardware models after concrete has dried , <br /> needs to be coated in the field . Note : Nipple length is determined by measuring from <br /> the bottom of the threaded portion of the base to the <br /> Step 2 : ( See Figure 1 & 2) bottom of the cover. Then subtract 2 " for clearance , <br /> Set riser pipe . " L" is the distance between the top of height of adaptor and height of cap . Range of nipple <br /> the riser pipe and finish grade . lengths that can be used in all of the OPW spill <br /> Note: The "L " dimensions below factors in a containers : 4" minimum to 14 maximum . <br /> 1 " slope to grade. <br /> Model Series " L" Dimension Finish Grade <br /> 1 -2100 , 5 Gal . ( Comp . Base) L= 15 5/8" (40cm) <br /> 1 -2100E , 7 . 5 Gal . (Comp . Base) L= 19 5/8" (50cm) <br /> 1 -21151 15 Gal . (Comp . Base ) L= 19 5/8" ( 50cm) <br /> L <br /> 1 -2100C , 5 Gal . (Cast Iron Base) L= 14 1 /2 " ( 37cm) <br /> 1 -2100EC , 7 . 5 Gal . (Cast Iron Base) L= 18 1 /2 " (47cm ) <br /> 1 -2115C , 15 Gal . (Cast Iron Base ) L= 18 1 /2 " (47cm) <br /> Note : Figure 1 <br /> If using OPW FSA400, add 3- 1/4 " to Dimension "L ". <br /> If using OPW FSA-400-S, add 1 -3/4 to Dimension 1 ". <br /> NOTE: FSA400-S will only work with Cast Iron Base, Finish Grade Slope V min . <br /> Step 3 : <br /> Deburr and thoroughly clean riser pipe . Apply pipe ,o <br /> dope to riser threads . Pipe dope to be a non - `o :� Q `o ; o <br /> hardening , gasoline resistant pipe thread seal ° ° o ' ° co�ivcRETE <br /> 0 <br /> compound . <br /> Step 4 : Dust Cap <br /> Install OPW FSA-400 Face Seal Adapter onto riser Adaptor <br /> using the OPW 61 SA-TOOL . Torque to 125 ft-lbs j Nipple <br /> min . to 250 ft- Ibs max. ( 4 " NPT) . Apply pipe dope to L <br /> FSA-400 . Pipe dope to be a non - hardening , gasoline <br /> resistant pipe thread seal compound . Bottom of <br /> thread in base <br /> Step 5 : <br /> Install spill container by rotating the mounting ring until <br /> hand tight . Top of Riser Pipe <br /> NOTE: Do not attempt to completely tighten the — <br /> container by using the mounting ring <br /> Step 6 : Riser Pipe <br /> Finish tightening the spill container with the OPW <br /> 61SA-TOOL . Torque to 125 ft- lbs min . to 250 ft . Lbs . <br /> max. (4 " NPT) <br /> Note: Ground riser pipe to nearest grounding rod. <br /> Step 7 : (See Figure 2 ) Figure 2 <br /> Apply pipe dope to nipple and install . Pipe dope to be <br /> OPW 1 -21 00 Series Spill Container Page 2 <br />