WORK PLANS - Laserfiche WebLink

Home Browse Search

Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Do not install in a garage. Failure to do so can result in death, explosion, or fire. I rig.in #z _ Location Requirements A WARNING Select proper location for your washer/dryer to improve performance and minimize noise and possible "washer walk." Install your washer/dryer in a basement, laundry room, closet, or recessed area. You will need: MI A location that allows for proper exhaust installation. A washer/dryer must be exhausted to the outdoors. See "Venting Requirements." For 27" (69 cm) and 24" (61 cm) 240V electric models, a separate 30 amp circuit. For 24" (61 cm) 120V electric models, a separate 20 amp circuit. For gas models, a separate 120V 15 or 20 amp circuit. For 27" (69 cm) electric models using a power supply cord, for 24" (61 cm) electric models, and for gas models, a grounded electrical outlet located within 2 ft (610 mm) of either side of the washer/dryer. See "Electrical Requirements." A sturdy floor to support the washer/dryer weight (washer/ dryer, water, and load) of 500 lbs (226.8 kg). MI A level floor with a maximum slope of 1" (25 mm) under entire washer/dryer. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if washer/dryer is not level. Installing on carpet is not recommended. A water heater set to deliver 120°F (49°C) water to the washer. Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-689.6 kPa). The washer/dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Do not operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer/Dryer Care" in the Washer/Dryer Use and Care Guide for winterizing information. Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. Check code requirements. Some codes limit, or do not permit, installation of the washer/dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector. Recessed area or closet installation The spacing dimensions on the following pages are recommended for this washer/dryer. This washer/dryer has been tested for spacing of 0" (0 mm) clearance at the sides and back. Recommended spacing should be considered for the following reasons: Additional spacing should be considered for ease of installation and servicing. Additional clearances might be required for wall, door, and floor moldings. MI Additional spacing on all sides of the washer/dryer is recommended to reduce noise transfer. For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. NOTE: For gas models, no other fuel-burning appliance can be installed in the same closet as the washer/dryer. Mobile Home - Additional Installation Requirements This washer/dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or the Canadian Manufactured Home Standard, CAN/CSA-Z240 MH. Mobile home installations require: Metal exhaust system hardware, which is available for purchase from your dealer. Mobile Home Installation Kit Part Number 346764 (gas models only). See "Tools and Parts" for ordering information. Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening. 7