COMPLIANCE INFO_2025 - Laserfiche WebLink

Home Browse Search

PEURP1200-12 6.2_1 Purpose_ T hiS Fnatlind K used to teat tbo 5. if tha shill bucket is fmmd to have erodes, loase integrity of single-walled spill buckets or the. pl i- parts or separation of the bucket from the fill many contuinmeru of secandadly conlainud shill pipe, it is not comddcred to be liquid-tight. 'fills bur kets. visually iudicaws a test failure. 5.2.2 Dorwription of Test. The spill bucket is NOTE: It' the fill cap is not included in the ft fled with water.The water level is measu red at the spill bucket test and/or the cap is not tight,it bt:girming and and or thu trzt, enuld he the Rouret:of potential Fuel contami- is.2.3 Test Equipment. Tbst ccluipimcal shall natisin from water intrtlsiun. Include: NOTE; Befarr pcarnancntly plugging, eq%urc: watts; Hiatt local rcgulatiumq Aluw the druid vnivc lu • measuring stick that is accurate, to within T/16 he permancntly plugged. (0.063) inch and of sufficient length; plumber's plug (Appropriate sim, if use4}; 6.2.5 Test Procedure. ■ stupwakeh or other lim&-ne_isurnnc:nt duvim :L Add water lv the spill bucket to a level withi,i cap ablo of measuring a 1-second Increment. 1.5 inches of the toy, or Elie spill bucket.Allow the„water to settle.for 5 rnimites before the initial 6.2.4 Preparation. water Icvcl irierstssunerricnt i:i taken. i Care should be taken whcti conducting the- test 2. Kim the measuring Mick verticstily A the lowest in the rein or during freezing weather candi- point in the spit}bucket and extending above the duns. water level to allow for an acccutate ineasure- 2.Remove and properly dispose of any liquid and meiif to be taken. The locaUoa of the measuring duhris (lcav�, sediment and Innh) in tht: isjiM stick must remain the same FuT rzuh watu level bucket,Clean the spill Bucket and examine it for measnrerneut. Document the initial water level damage, defects or imprctperiy insta€Jed compo- cc xisurt't�cnt a$ tricasttreel rl'piTi tire- hattoiii of ncnty, if there arc loose componen[s (e.g., lnnse the spill bucket.Ahemadve measuizmcnt MUh- band clamps or balks), tightcn these items befom ods may he kised provided that messsureiment to conducting the integrity test. If there are itanis 1/16(0,063) inuh cats be 111a[Ic. that must be yie xda d or tieplared (e.g., deterio- 3.Thke all prrec ailtkins Ir) prevent the water ic:vcl rated guk%_.Eslscals or dmin valvuA 7iotify the rtnin heing disaudierl during the duratian of the ownerlope ator. Lost. S.Examine this fill cap and adapter fitting for 4. After I hour, document the ending watts level loofa;, missing or damageJ parts. anel Make �iicresutitinterit necessary repairs. Complete any repairs; before 5. Upon trckinplelion of this test, rcmcwc and tlis- puttii water in the spill bucket. Make sure dist.t the seal ou the fill cap is present and in good ficx.�e of life writer according to Sec:ticsn Cs.?, and heP inside of Spill buck dry eanelitimm.The cup must fit mxaimly and hu leak- the before retarriirtg it to seXYice. tight tin the riser. T ie' water level duriikg the test typically will be above the cap,so a leaking cap 6.2.6 Pass/Fall Criteria. if the water level has will result in a failed test.As an aimMativc to a dRipped less than 1/8 (0,125)inch,the spill bUC:lGt;t tlgh t fil l cap, use a pl umber's p kig in t he rill riser p tsges the integrity test. if npproyed by the iinthorhy having jurisdiction (AUT) and tank owjwr. If the water level has dropped 118 (0.125) inch cw �;1�ater, the-;pill hucket fail,4 the inwgnty test. 4. '1'iic ypiil-biieket drainvnlvC, if present, iciestgmaLar, be, leak-tigh( to pass the test. If it is riot leak- 6.3 Spill 9ucket Integrity Testing — Vacuum TOO zlghc. it may he possible to simply remove and Method. jAmiliins:ntly ping the drain valve, Hr)wcvcr, if you chuosc to pernituicutly slug, ensure that the 6.3.1 Purpose. This medtiod is used to test the local mgulations allow this modification. integrity of ssinglu-witllud spill birt.kcu ut the. pri- pei.org