COMPLIANCE INFO_PRE 2019 - Laserfiche WebLink

Home Browse Search

Unified STOCKTON DISTRIBUTION OPERATING PROCEDURES Janitor Scrub Aisles/Docks. Customer 999002 1. You will need to obtain a scrubber key from your supervisor. 2. Sign into your assignment then proceed to the scrubber location adjacent to the battery room. 3. You will then proceed to the location which Vocollect sends you to. 4. Confirm the location via the check digit which is on the slot tag located on the rack or above the exit door on the dock. 5. Once you give the check digit, listen carefully to the amount of cases being requested by the Vocollect unit. The case quantity is referring to the amount passes that are required to clean the area. For example, if it says six and you used all six passes then say "six" if you only used five of the six passes then say "five". When scrubbing, you will make enough passes up and down the aisle to make sure you cover the entire area, which is an average of 6 passes depending on the width of the aisle. 6. When scrubbing the docks, you will make enough passes to cover the entire area, which will be different depending on the dock you are working on. 7. Obtain a direct task from your supervisor to dump and change the water during the shift as needed. 8. At the end of the shift, you will need to drive the scrubber to the dumping station, dump the dirty water and replace it with clean water for the next person. Never leave dirty water in the scrubber. Make sure to clean out the fro bris. 9. Make sure all the dirty water from the scrubber tank goes down the wash rack drain. If any spillsv e 10. Park equipment in assigned area, and plug it back in so it charges the battery. 11. Proceed with your next assignment U Scrubbing Pick Modules E M�4Y 29 2#t4 1. Sign into your assignment. Dn-o 1JZfV7A 2. Pick modules will require you to obtain the hand scrubber from the location in front of the shipping offi 3. Fill the scrubber with water & vinegar. t;� �- 4. Confirm you are in the right location via the check digit on the rack at the bottom of the stair well. 5. Pick up debris from floor and pre -treat heavy soiled areas prior to scrubbing. 6. You will then scrub the entire module making 6 passes per level, 3 passes on each side of the belt. 7. When you finish the entire module, you will need to take the scrubber to the dumping station and replace the dirty water. Never leave dirty water in the scrubber. 8. Make sure all the dirty water from the scrubber tank goes down the wash rack drain. If any spills over the side scrub it up. 9. Park equipment in assigned area, and plug it back in so it charges the battery. 10. Proceed with your next assignment. Aisles: Sweep empty slots, pick up debris, damage, recoup product, cleaning the modules, and cleaning the dock. Customer 999003 1. You will need a garbage bin, broom, scan gun (for adjusting inventory), absorb it, and a flatbed cart for damage/recoup. 2. Each assignment will include several aisles. 3. Sign into your assignment then proceed to the directed aisle. Confirm you are at the correct aisle by saying the check digit. 4. Proceed down the aisle picking up debris, sticks, paper, cardboard, damage, cases that need re -coupled, put back overstock in the proper pick slot or items that have fallen off the pallet, sweep empty slots, in-between slots, and end caps. The aisle should be neat and orderly as you go through it; this includes the back side of the flow racks in the modules. If the slot or in-between the pallet has recently been cleaned then don't sweep it. • Clean pits from door 70-78 on Monday/Wednesday- invoice 2 AM only. 5. Use inventory gun to take damage, orphan or recoup cases out of inventory using "WD-". Use your secondary employee number that starts with "9". Separate wet damage from dry, as well as orphan cases and recoup cases. 6. If you come across a garbage can that needs to be dumped, you are required to dump the can. 7. At the end of each aisle, you will continue a path to the dock doors. Pick up all trash and debris in this area. 8. Continue the assignment until all pick slots have been completed. This is accomplished by following the Vocollect voice selection system. 9. At the end of the shift, Please replace dust mop head with a clean one, place dirty one in the proper receptacle. Make sure all bins, shovels, brooms, wheelers and carts are in the designated locations for the next shift. 11/28/11 2