INSTALL_1997 - Laserfiche WebLink

Home Browse Search

OH Attached Collar (AC) This fiberglass attached collar, without Flange, can be used to surround the fitting(s) or manway. The collar can be used with attached collar risers (as shown below in I & J). I.D.'s can be 42" or 48". Strap locations can be affected. Use of only one riser will be permitted on sizes 600 thru 3,000 gallons. Maximum use �Q of two riser will only be allowed on 4,000 - b' dia. or 6,000 - 8' dia. or larger tanks. OI Attached Collar Riser (ACR) This fiberglass attached collar riser is intended for use with a 48"dia meter attached cd collar. (This is sold separately. See H.) Riser body is 42" or 48" 1. D., with a Flat top and a 22" or 32"diameter friction fit cover within top. This riser provides an en- closure for a submersible pump and also provides a termination point for double wall piping systems. The bonding of riser to collar is to be done by the contractor. (Adhesive kits are included.) JO Watertight Attached Collar Riser (ACRWT) This fiberglass watertight attached collar riser is in- tended for use with a 42" or 48" diameter attached collar. (This is sold separately. See H.) The riser body is 42" or 48" I.D. with a 26" diameter opening. This provides an en- closure for a submersible pump and also provides a termination point for double- wall piping systems. The bonding of the riser to the collar and the top to the riser is done by the contractor. (Adhesive kits are included.) 12 OK Secondary Contained Service Fittings C1 Secondary contained service fittings, typically a 4" NPT within a 6" NPT, allow the tank to be connected to a secondary contained piping system. Grommet Kits When high water conditions do not exist, electrical con- nections field and secondary piping can can be field installed on an attached collar riser using optional rubber grommets. (0) Grommets are available in the following sizes 3/4" for 3/4" O.D. electrical conduit I" for 1" O.D. electrical conduit 2", 3" and 4" for 2", 3" & 4" O.D. FRP pipe Each kit includes six (6) grommets. MO Fiberglass Bulkhead Coupling Kit The 3" FRP coupling is a two-piece fitting that is bonded to the attached collar riser by the contractor, f '" The male and female sections; of the FRP coupling are threaded together to hold the fitting in place while the S adhesive cures. Each kit in - dudes one 3" FRP coupling, ; adhesive and instructions. NO Electrical Bulkhead Coupling Kit The 1" electrical coupling kit is a three-piece fitting which is bonded to the attached collar riser by the contractor. The male and female sections are threaded together to hold the electrical coupling in place while the adhesive cures. Each kit in- cludes four I " steel couplings, adhesive and instructions. 77 71 iK Optional Tank Accessor les b OH Attached Collar (AC) This fiberglass attached collar, without Flange, can be used to surround the fitting(s) or manway. The collar can be used with attached collar risers (as shown below in I & J). I.D.'s can be 42" or 48". Strap locations can be affected. Use of only one riser will be permitted on sizes 600 thru 3,000 gallons. Maximum use �Q of two riser will only be allowed on 4,000 - b' dia. or 6,000 - 8' dia. or larger tanks. OI Attached Collar Riser (ACR) This fiberglass attached collar riser is intended for use with a 48"dia meter attached cd collar. (This is sold separately. See H.) Riser body is 42" or 48" 1. D., with a Flat top and a 22" or 32"diameter friction fit cover within top. This riser provides an en- closure for a submersible pump and also provides a termination point for double wall piping systems. The bonding of riser to collar is to be done by the contractor. (Adhesive kits are included.) JO Watertight Attached Collar Riser (ACRWT) This fiberglass watertight attached collar riser is in- tended for use with a 42" or 48" diameter attached collar. (This is sold separately. See H.) The riser body is 42" or 48" I.D. with a 26" diameter opening. This provides an en- closure for a submersible pump and also provides a termination point for double- wall piping systems. The bonding of the riser to the collar and the top to the riser is done by the contractor. (Adhesive kits are included.) 12 OK Secondary Contained Service Fittings C1 Secondary contained service fittings, typically a 4" NPT within a 6" NPT, allow the tank to be connected to a secondary contained piping system. Grommet Kits When high water conditions do not exist, electrical con- nections field and secondary piping can can be field installed on an attached collar riser using optional rubber grommets. (0) Grommets are available in the following sizes 3/4" for 3/4" O.D. electrical conduit I" for 1" O.D. electrical conduit 2", 3" and 4" for 2", 3" & 4" O.D. FRP pipe Each kit includes six (6) grommets. MO Fiberglass Bulkhead Coupling Kit The 3" FRP coupling is a two-piece fitting that is bonded to the attached collar riser by the contractor, f '" The male and female sections; of the FRP coupling are threaded together to hold the fitting in place while the S adhesive cures. Each kit in - dudes one 3" FRP coupling, ; adhesive and instructions. NO Electrical Bulkhead Coupling Kit The 1" electrical coupling kit is a three-piece fitting which is bonded to the attached collar riser by the contractor. The male and female sections are threaded together to hold the electrical coupling in place while the adhesive cures. Each kit in- cludes four I " steel couplings, adhesive and instructions.