Laserfiche WebLink
GICO <br /> � bo <br /> iIcxrcPR*INSTALLATION INSTRUCTION`S <br /> 1. Use a standard 4" tank locking cap, "Evertite" or equiva- <br /> lent, with standard ring adaptor. <br /> PROBE RISER PIPE <br /> TANK 2. Drill and tap the cap for a 3/8 x 18 NPT cord grip thread <br /> i (see Figure 3, "Probe Riser Cap Modification"). <br /> b <br /> 3. Install a water-tight cable bushing in the 3/8" threaded <br /> hole in the top of the cap. Use an appropriate thread <br /> a sealant to ensure water-tightness. Also install a water-tight <br /> a-b=c cable bushing in the probe junction box in a similar manner. <br /> Figure 1. Tank Diameter Measurement ±.062 <br /> 1.438 � �375 — 18 N.P.T. <br /> A=LENGTH OF PROBE <br /> (lank 0.1 <br /> .a s- P ry.22 m1 a <br /> s (lszm) ±.062 <br /> _ 54-(1.62 m) 1625 __ _ <br /> 6' (I8 . <br /> 3 m1 <br /> 2.0 m <br /> 7' (2 13.) <br /> 7'6"(2.28 m) <br /> 8' 1244 m) '�1Il tJ3n� <br /> 25m <br /> 267. <br /> 9' (274. <br /> L 30. <br /> 10' (3.05 m) <br /> 10'6"(320.) <br /> n' (3.35m) Figure 3. Probe Riser Cap Modification <br /> C. PROBE RISER ADAPTOR INSTALLATION. <br /> Figure 2. Magnetostrictive Probe Dimensions (Figure illustrates 1. Remove the probe from its box and place it on its side. <br /> Magnetostrictive Probe with 4" Floats) Remove the probe riser adaptors from the Magnetostrictive <br /> Probe Installation Kit box (see Figure 4 or 5). <br /> 2. Place one riser adaptor on top of the probe canister with <br /> B. RISER PIPE CAP PREPARATION. The riser pipe cap its bevelled edge down and its locking tabs aligned with the <br /> preparation must have a 3/8" tapped hole for passage of Oats on the canister (see Figure 6 or 7). <br /> probe wires. Cap kits with pre-drilled holes for a standard <br /> 4" riser pipe are available from Gilbarco. Order Kit Number 3. Press the adaptor onto the canister until the locking tabs <br /> Q12598-05, one for each probe. are on the Oats. Twist the adaptor until the tabs are on the <br /> If a kit has not been ordered, perform the following: diameter of the canister and slide the adaptor to the bottom <br /> of the canister. <br /> 't, WARNING: DO NOT PERFORM DRILLING 4. Once the adaptor is at the bottom of the canister, twist <br /> �yyyJrrr, AND TAPPING PROCEDURES IN A IIAZ- the adaptor until its locking tabs snap into the locking <br /> ARDOUS AREA. DRILLING AND TAPPING grooves. <br /> CAN CAUSE SPARKS AND IGNITE VOL- <br /> ATILE FUMES AND LIQUIDS FOUND IN A 5. Place the other adaptor on top of the probe canister with <br /> CLASS I, GROUP D HAZARDOUS LOCA- its beveled edge up and its locking tabs aligned with the flats <br /> N. FAILURE TO COMPLY COULD on the canister. <br /> RESULT IN DEATH, SERIOUS PERSONAL 6. Press the adaptor onto the canister until the locking tabs <br /> INJURY, PROPERTY LOSS AND EQUIP. are on the flats. Twist the adaptor until its locking tabs snap <br /> MENT DAMAGE. into the locking grooves. <br /> 2 <br />