INSTALL 2019 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed Red Thread®11 A Piping System SPECIFICATION GUIDE Primary Piping SECTION 1 - Scope This section covers the use of fiberglass reinforced plastic (FRP) pipe for single wall fuel handling and fuel handling vent and vapor applications including gasoline, unleaded gasoline, gasoline/alcohol mixtures, bio -diesel, DEF and diesel up to 150°F and 250 psig cyclic pressure. SECTION 2 - General Conditions 2.01 Coordination - Material furnished and work performed under this section shall be coordinated with the related work and equipment specified under other sections, i.e. Valves, Flexible Connectors, Equipment. 2.02 Governing Standards - Except as modified or supplemented herein, all materials and construction methods shall comply with and be tested in accordance with the following standards and test methods: Standards and Test Methods: UL971 2004 Standard for Nonmetallic Underground Piping for Flam- mable Liquids ASTM Standard Classification for Machine -Made "Fiberglass" D2310 (Glass Fiber Reinforced Thermosetting Resin) Pipe ASTM Standard practice for obtaining Hydrostatic or Pressure D2992 Design Basis for "Fiberglass" (Glass Fiber Reinforced Thermosetting Resin) Pipe and Fittings 2.03 Operating Conditions - In addition to the above listed minimum design requirements, the system shall meet the following minimum operating conditions: a. Operating Pressure b. Fluid Conveyed c. Test Pressure 2.04 Quality Assurance - Pipe manufacturer's quality program shall be in compliance with ISO 9001 and/or API Q1. 2.05 Delivery. Storage, and Handling - Pipe and fittings shall be protected from damage due to impact and point loading. Pipe shall be properly supported to avoid damage due to flexural strain. The contractor shall not allow dirt, debris or other extraneous materials to get into pipe and fittings. All factory machined areas shall be protected from sunlight until installed. 2.06 Acceptable Manufacturers - NOV Fiber Glass Systems, 501-568-4010, or approved equal. Section 3 - Material and Construction 3.01 2"-4" Pipe - The pipe shall be manufactured by the filament winding process using an amine cured epoxy thermosetting resin to impregnate strands of continuous glass filaments, which are wound around a mandrel at a 543/4" winding angle under controlled tension. The pipe shall be heat cured and the cure shall be confirmed using a Differential Scanning Calorimeter. Pipe shall be supplied with a T.A.B." (Threaded and Bonded) ends. Pipe shall have a minimum continuous cyclic pressure rating of 125 psig at 150OF in accordance with ASTM D2992, Procedure A or UL 971 pressure rating. All pipe shall be 100% hydrotested at the factory before shipment at a minimum pressure of 255 psig and shall be UL971-2004 Listed and labeled. 3.02 ASTM D2310 Classifications (at 73.41F) 2" - 3" RTRP-1 1 AF 4" RTRP-1 1 AH (Mechanical properties cell classifications shown are minimums.) 3.03 Fittinas - All fittings shall be manufactured using the same type of material as the pipe. Fittings may be manufactured either by compression molding, filament winding, resin transfer molding or contact molding methods. All fittings, adapter, and sump penetrations shall be UL971- 2004 Listed. Fittings shall be adhesive bonded matched tapered bell and spigot. 3.04 Connections - Connections to flex connectors or other piping materials shall be made by the use of NPT (National Pipe Thread) threaded adapters or flanges bonded to the FRP piping system. 3.05 Sump Penetrations - Sump penetrations shall be made by means of a permanently bonded FRP coupling. The coupling shall be capable of adjusting for the slope of the piping system entering or exiting the sump wall. 3.06 Adhesives - Adhesives shall be manufacturer's standard for the piping system specified. www.fgspipe.com • fgspipe@nov.com NW Fiber Glass -Systems