|
ACCESSIBLE ROUTE (CBC 11B-402)
<br />IIB -402.1 General. Accessible routes shall comply with
<br />11B-402.
<br />IIB -402.2 Components. Accessible routes shall consist of
<br />one or more of the following components: walking surfaces
<br />with a running slope not steeper than 1:20, doorways, ramps,
<br />curb ramps excluding the flared sides, elevators, and platform
<br />lifts. All components of an accessible route shall comply with
<br />the applicable requirements of Division 4.
<br />IIB -403 Walking surfaces
<br />IIB -403.1 General. Walking surfaces that are a part of an
<br />accessible route shall comply with Section IIB -403.
<br />IIB -403.2 Floor or ground surface. Floor of ground sur-
<br />faces shall comply with Section IIB -302.
<br />IIB -403.3 Slope. The running slope of walking surfaces
<br />shall not be steeper than 1:20. The cross slope of walking sur-
<br />faces shall not be steeper than 1:48.
<br />Exception: The running slope of sidewalks shall not
<br />exceed the general grade established for the adjacent
<br />street or highway.
<br />I1B-403.4 Changes in level. Changes in level shall comply
<br />with Section JIB -303.
<br />IIB -403.5 Clearances. Walking surfaces shall provide clear-
<br />ances complying with Section IIB -403.5.
<br />Exception: Within employee work areas, clearances on
<br />common use circulation paths shall be permitted to be
<br />decreased by work area equipment provided that the
<br />decrease is essential to the function of the work being per-
<br />formed.
<br />11B-403.5.1 Clear width. Except as provided in Sections
<br />11B-403.5.2 and IIB -403.5.3, the clear width of walking
<br />surfaces shall be 36 inches (914 mm) minimum.
<br />Exceptions:
<br />1. The clear width shall be permitted to be reduced
<br />to 32 inches (813 mm) minimum for a length of
<br />24 inches (610 nun) maximum provided that
<br />reduced width segments are separated by seg-
<br />ments that are 48 inches (1219 mm) long mini-
<br />mum and 36 inches (914 mm) wide minimum.
<br />2. The clear width for walking surfaces in corridors
<br />serving an occupant load of 10 or more shall be
<br />44 inches (1118 mm) minimum.
<br />3. The clear width for sidewalks and walks shall be
<br />48 inches (1219 mm) minimum. When, because of
<br />right-of-way restrictions, natural barriers or
<br />other existing conditions, the enforcing agency
<br />determines that compliance with the 48 -inch
<br />(1219 mm) clear sidewalk width would create an
<br />unreasonable hardship, the clear width may be
<br />reduced to 36 inches f 914 mm).
<br />4. The clear width for aisles shall be 36 inches (914
<br />mm) minimum if serving elements on only one
<br />side, and 44 inches (1] 18 mm) minimum if serv-
<br />ing elements on both sides.
<br />DOORS, DOORWAYS, AND GATES (CBC 11 B-404)
<br />IIB -403.5.2 Clear width at turn. Where the accessible
<br />route makes a 180 degree tum around an element which is
<br />less than 48 inches (1219 mm) wide, clear width shall be
<br />42 inches (1067 mm) minimum approaching the turn, 48
<br />inches (1219 mm) minimum at the tum and 42 inches
<br />(1067 mm) minimum leaving the turn.
<br />Exception: Where the clear width at the turn is 60
<br />inches (1524 mm) minimum compliance with Section
<br />IIB -403.5.2 shall not be required.
<br />I1B-403.5.3 Passing spaces. An accessible route with a
<br />clear width less than 60 inches (1524 mm) shall provide
<br />passing spaces at intervals of 200 feet (60,960 mm) maxi-
<br />mum. Passing spaces shall be either: a space 60 inches
<br />(1524 mm) minimum by 60 inches (1524 mm) minimum-,
<br />or, an intersection of two walking surfaces providing a T-
<br />shaped space complying with Section IIB -304.3.2 where
<br />the base and arms of the T-shaped space extend 48 inches
<br />(1219 mm) minimum beyond the intersection.
<br />IIB -403.6 Handrails. Where handrails are provided along
<br />walking surfaces with running slopes not steeper than 1:20
<br />they shall comply with Section IIB -505.
<br />11B-403.7 Continuous gradient. All walks with continuous
<br />gradients shall have resting areas, 60 inches (1524 mm) in
<br />length, at intervals of 400 feet (121,920 mm) maximum. The
<br />resting area shall be at least as wide as the walk. The slope of
<br />the resting area in all directions shall be 1:48 maximum.
<br />IIB -404.1 General. Doors, doorways, and gates that are part
<br />of an accessible route shall comply with Section IIB404.
<br />Exceptions.-
<br />1.
<br />xceptions:1. Doors, doorways, and gates designed to be operated
<br />only by security personnel shall not be required to
<br />comply with Sections IIB404.2.7, 11B404.2.8,
<br />lIB 404.2.9, 118-404.3.2 and 11B 404.3.4 through
<br />I1 B-404.3.7. A sign visible from the approach side
<br />complying with Section 11B-703.5 shall be posted
<br />stating "Entry restricted and controlled by security
<br />personnel".
<br />2. At detention and correctional facilities, doors, door-
<br />ways, and gates designed to be operated only by
<br />security personnel shall not be required to comply
<br />with Sections IIB -404.2.7, 11 B-404.2.8, 11B-
<br />404.2.9, 11 B-404.3.2 and I IB -404.3.4 through I 1 B-
<br />404.3.7.
<br />IIB -404.2 Manual doors, doorways, and manual gates
<br />Manual doors and doorways and manual gates intended for
<br />user passage shall comply with Section 11 B-404.2.
<br />1IB-404.2.1 Revolving doors, gates, and turnstiles.
<br />Revolving doors, revolving gates, and turnstiles shall not
<br />be part of an accessible route.
<br />11B-404.2.2 Double -leaf doors and gates. At least one of
<br />the active leaves of doorways with two leaves shall com-
<br />ply with Sections IIB -404.2.3 and IIB -404.2.4.
<br />IIB -404.2.3 Clear width. Door openings shall provide a
<br />clear width of 32 inches (813 mm) minimum. CIear open -
<br />11B -404.1 General. Doors, doorways, and gates that are part
<br />of an accessible route shall comply with Section IIB -404.
<br />Exceptions:
<br />1. Doors, doorways, and gates designed to be operated
<br />only by security personnel shall not be required to
<br />comply with Sections 11B-404.2.7, IIB404.2.8,
<br />11B-404.2.9, IIB -404.3.2 and 11B-404.3.4 through
<br />IIB -404.3.7. A sign visible from the approach side
<br />complying with Section IIB -703.5 shall be posted
<br />stating "Entry restricted and controlled by security
<br />personnel ".
<br />2. At detention and correctional facilities, doors, door-
<br />ways, and gates designed to be operated only by
<br />security personnel shall not be required to comply
<br />with Sections 11B-404.2.7, JIB -404.2.8, 11B-
<br />404.2.9, 11 B-404.3.2 and 11 B-404.3.4 through 11 B-
<br />404.3.7.
<br />I1B-404.2 Manual doors, doorways, and manual gates
<br />Manual doors and doorways and manual gates intended for
<br />user passage shall comply with Section IIB -404.2.
<br />IIB -404.2.1 Revolving doors, gates, and turnstiles.
<br />Revolving doors, revolving gates, and turnstiles shall not
<br />be part of an accessible route.
<br />11B-404.2.2 Double -leaf doors and gates. At least one of
<br />the active leaves of doorways with two leaves shall com-
<br />ply with Sections I IB -404.2.3 and I1 B-404.2.4.
<br />11B-404.2.3 Clear width. Door openings shall provide a
<br />clear width of 32 inches (813 mm) minimum. Clear open-
<br />ings of doorways with swinging doors shall be measured
<br />between the face of the door and the stop, with the door
<br />open 90 degrees. Openings more than 24 inches (610 mm)
<br />deep shall provide a clear opening of 36 inches (914 mm)
<br />minimum. There shall be no projections into the required
<br />clear opening width lower than 34 inches (864 mm) above
<br />the finish floor or ground. Projections into the clear open-
<br />ing width between 34 inches (864 mm) and 80 inches
<br />(2032 mm) above the finish floor or ground shall not
<br />exceed 4 inches (102 mm).
<br />KNEE AND TOE CLEARANCE (CBC 11B-302)
<br />1111-306.1 General. Where space beneath :in clement is-
<br />included
<br />sincluded as part of clear floor or ground space or turning
<br />space, the space shall comply with Section IIB -306. Addi-
<br />tional space shall not be prohibited beneath an element but
<br />shall not be considered as part of the clear floor or ground
<br />space or turning space.
<br />IIB -306.2 Toe clearance
<br />11B-306.2.1 General. Space under an element between
<br />_ `---------------
<br />_ I
<br />9 i to
<br />4 229 i M "
<br />LI "1_ _J
<br />L--------- ----J -1r
<br />6 Max 17-25
<br />152 432335
<br />(a) (5)
<br />elevation plan
<br />FIGURE 11B-306.2
<br />TOE CLEARANCE
<br />the finish floor or ground and 9 inches (229 min) above
<br />the finish floor or around shall be considered toe clearance
<br />and shall comply with Section IIB -3062.
<br />11B-306.2.2 Maximum depth. Toe clearance sliall extend
<br />25 inches (635 matt) maximum under an element.
<br />Exception. Toe clearance shall extend 19 inches (483
<br />mni) maximum under lavatories required to be accessi-
<br />ble by Section 11 B-213.3.4.
<br />IIB -306.2.3 Minimum required depth. Where toe clear-
<br />ance is required at an element as part of a clear floor space,
<br />the toe clearance shall extend 17 inches (432 mm) mini-
<br />mum under the element.
<br />Exceptions:
<br />1. The toe clearance shall extend 19 inches (483
<br />mm) minimum under sinks required to be accessi-
<br />ble by Section IIB -212.3.
<br />2. The toe clearance shall extend 19 inches (483
<br />mm) minimum under built-in dining and work
<br />surfaces required to be accessible k1, Section
<br />1 IB -226. 1.
<br />IIB -306.2.4 Additional clearance. Space extending
<br />greater than 6 inches (152 mm) beyond the available knee
<br />clearance at 9 inches (229 mm) above the finish floor or
<br />ground shall not be considered toe clearance.
<br />11B-306.2.5 Width. Toe clearance shall be 30 inches (762
<br />mm) wide minimum.
<br />11B-306.3 Knee clearance.
<br />JIB -306.3.1 General. Space under an element between 9
<br />inches (229 mm) and 27 inches (686 mm) above the finish
<br />floor or ground shall be considered knee clearance and
<br />shall comply with Section 11B-306.3.
<br />Exception: At lavatories required to be accessible by
<br />Section 118-213.3.4, space between 9 inches (229 mnr)
<br />and 29 inches (737 mm) above the finish floor or
<br />ground, shall be considered knee clearance.
<br />IIB -306.3.2 Maximum depth. Knee clearance shall
<br />extend 25 inches (635 mm) maximum under an element at
<br />9 inches (229 mm) above the finish floor or ground.
<br />11B-306.3.3 Minimum required depth. Where knee
<br />clearance is required under an element as part of a clear
<br />floor space, the knee clearance shall be ll inches (279
<br />min) deep minimum at 9 inches (229 mm) above the finish
<br />floor or ground, and 8 inches (203 mm) deep minimum at
<br />27 inches (686 mm) above the finish floor or ground.
<br />Exceptions:
<br />1. At lavatories required to he accessible by Section
<br />IIB -213.3.4, the knee clearance shall be 27
<br />inches (686 rnm) high mininrunl above the finish
<br />floor or ground at a depth of 8 inches (203 nein)
<br />mininitan increasing to 29 inches (737 mm) high
<br />ininim um above the finish floor or ground at the
<br />front edge of a counter tviih a built-in lavatory or
<br />at the front edge of a wall -mounted lavatoryfix-
<br />lure.
<br />REACH RANGES (CBC 11 B-308)
<br />IIB -308 Reach ranges
<br />IIB -308.1 General. Reach ranges shall comply with Section
<br />I IB -308,
<br />IIB -308.1.1 Electrical switches. Controls and switches
<br />intended to be used by the occupant of a room or area to
<br />control lighting and receptacle outlets, appliances or
<br />cooling, heating and ventilating equipment, shall comply
<br />with Section IIB -308 except tine low reach shall be mea-
<br />sured to the bottom of the outlet box and the high reach
<br />shall be measured to the top of the outlet box.
<br />IIB -308.1.2 Electrical receptacle outlets. Electrical
<br />receptacle outlets on branch circuits of 30 amperes or less
<br />and communication system receptacles shall comply with
<br />Section iIB-308 except the low reach shall be measured
<br />to the bottom of the outlet box and the high reach shall be
<br />measured to the top of the outlet box.
<br />I1B-308.2 Forward reach.
<br />IIB -308.2.1 Unobstructed. Where a forward reach is
<br />unobstructed, the high forward reach shall be 48 inches
<br />(1219 mm) maximum and the low forward reach shall be
<br />15 inches (381 mm) minimum above the finish floor or
<br />ground.
<br />IIB -308.2.2 Obstructed high reach. Where a high for-
<br />ward reach is over an obstruction, the clear floor space
<br />shall extend beneath the element for a distance not less
<br />E EIUD co
<br />°'
<br />FIGURE 11B308.2.1
<br />UNOBSTRUCTED FORWARD REACH
<br />than the required reach depth over the obstruction. The
<br />high forward reach shall be 48 inches (1219 mm) maxi-
<br />mum where the reach depth is 20 inches (508 mm) maxi-
<br />mum. Where the reach depth exceeds 20 inches (508 mm),
<br />the high forward reach shall be 44 inches (1118 mm) max-
<br />imum and the reach depth shall be 25 inches (635 mm)
<br />maximum.
<br />B-308.3 Side reach.
<br />11B-308.3.1 Unobstructed. Where a clear floor or ground
<br />20 max >20-25 max
<br />Soo
<br />c
<br />(a) (b)
<br />FIGURE 118-308.2.2
<br />OBSTRUCTED HIGH FORWARD REACH
<br />space allows a parallel approach to an element and the side
<br />reach is unobstructed, the high side reach shall be 48
<br />inches (1219 mm) maximum and the low side reach shall
<br />be 15 inches (381 mm) minimum above the finish floor or
<br />ground.
<br />Exceptions:
<br />1. An obstruction shall be permitted between the
<br />clear floor or ground space and the element
<br />where the depth of the obstruction is 10 inches
<br />(254 mm) maximum.
<br />2. Operable parts of fuel dispensers shall be permit-
<br />ted to be 54 inches (1372 mm) maximum mea-
<br />sured from the surface of the vehicular way
<br />where fuel dispensers are installed on existing
<br />curbs.
<br />IIB -308.3.2 Obstructed high reach. Where a clear floor
<br />or ground space allows a parallel approach to an element
<br />and the high side reach is over an obstruction, the height of
<br />the obstruction shall be 34 inches (864 mm) maximum and
<br />the depth of the obstruction shall he 24 inches (610 mm)
<br />maximum. The high side reach shall be 48 inches (1219
<br />mm) maximum for a reach depth of 10 inches (254 mm)
<br />maximum. Where the reach depth exceeds 10 inches (254
<br />mm), the high side reach shall be 46 inches (1168 mm)
<br />maximum for a reach depth of 24 inches (610 mm) maxi-
<br />mum.
<br />Exceptions:
<br />I. The top of washing machines and clothes dryers
<br />shall be permitted to be 36 inches (914 mm) max-
<br />imum above the finish floor.
<br />2. Operable parts of fuel dispensers shall be permit-
<br />ted to be 54 inches (1372 mm) maximum mea-
<br />sured from the surface of the vehicular way
<br />where fuel dispensers are installed on existing
<br />curbs..
<br />JIB -309 Operable parts
<br />IIB -309.1 General. Operable parts shall comply with Sec-
<br />tion IIB -309.
<br />IIB -309.2 Clear floor space. A clear floor or ground space
<br />complying with Section IIB -305 shall be provided.
<br />IIB -309.3 Height. Operable parts shall be placed within one
<br />or snore of the reach ranges specified in Section IIB -308.
<br />IIB -309.4 Operation. Operable parts shall be operable with
<br />one hand and shall not require tight grasping, pinching, or
<br />twisting of the wrist. The force required to activate operable
<br />parts shall be 5 pounds (22.2 N) maximum.
<br />Exception: Gas pump nozzles shall not be required to pro-
<br />vide operable parts that have an activating force of 5
<br />pounds (22.2 N) maxiinum,
<br />ACCESSIBLE PARKING REQUIREMENTS
<br />6"
<br />;D
<br />CI
<br />. r
<br />not in
<br />MEN-
<br />pictogram
<br />field
<br />FIGURE 116-703.6.1
<br />PICTOGRAM FIELD
<br />RAW
<br />TOGGLE
<br />D
<br />PUSH-PULL
<br />2r-81v� 34" MINIMUM
<br />MIN. 44" MAXIMUM A.F.F. (TYP.)
<br />LEVER
<br />21-8"DOOR CLEAR OPENING B DOOR HARDWARE
<br />MIN. -T ❑
<br />INTERNATIONAL SYMBOL OF ACCESSIBILITY 9 PICTOGRAM 5 DOORS & DOOR HARDWARE 1
<br />1. SWINGING DOOR AND GATE SURFACES WITHIN 10 INCHES OF THE FINISH FLOOR OR GROUND MEASURED VERTICALLY SHALL
<br />HAVE A SMOOTH SURFACE ON THE PUSH SIDE EXTENDING THE FULL WIDTH OF DOOR OR GATE. PARTS CREATING HORIZONTAL
<br />OR VERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN 1/16 INCH OF THE SAME PLANE AS THE OTHER AND BE FREE OF
<br />SHARP OR ABRASIVE EDGES. CAVITIES CREATED BY ADDED KICK PLATES SHALL BE CAPPED PER CBC SEC. 11B-404.2.10.
<br />AREA OF 2. THE FORCE FOR PUSHING OR PULLING OPEN A DOOR SHALL BE AS FOLLOWS:
<br />A. INTERIOR HINGED DOORS AND GATES: 5 POUND (22.2N) MAXIMUM.
<br />U E AREA OF B. SLIDING OR FOLDING DOORS: 5 POUNDS (22.2N) MAXIMUM
<br />REFUGE C. REQUIRED FIRE DOORS: THE MINIMUM OPENING FORCE ALLOWABLE BY THE APPROPRIATE
<br />LM ADMINISTRATIVE AUTHORITY, NOT TO EXCEED 15 POUNDS (66.7 N).
<br />D. EXTERIOR HINGED DOORS: 5 POUNDS (22.2N) MAXIMUM.
<br />X
<br />.o n
<br />E 3. THRESHOLDS, IF PROVIDED AT DOOR WAYS, SHALL BE 1/2" HIGH MAXIMUM. RAISED THRESHOLDS
<br />- AND CHANGES IN LEVEL AT DOORWAYS SHALL COMPLY WITH CBC SECTIONS 11B-302 AND 116-303.
<br />4, 318-1/2 4. DOOR AND GATE HARDWARE.
<br />HANDLES, PULLS, LATCHES, LOCKS, AND OTHER OPERABLE PARTS ON DOORS AND GATES SHALL COMPLY WITH
<br />3t8 5 CBC SECTION 11B-309.4.
<br />,,s OPERABLE PARTS OF SUCH HARDWARE SHALL BE 34 INCHES MINIMUM AND 44 INCHES MAXIMUM
<br />ABOVE THE FINISH FLOOR OR GROUND. WHERE SLIDING DOORS ARE IN THE FULLY OPEN POSITION, OPERATING HARDWARE
<br />SHALL BE EXPOSED AND USABLE FROM BOTH SIDES.
<br />FIGURE 118-703.3.2
<br />POSITION OF BRAILLE
<br />BRAILLE MEASUREMENT
<br />20 max
<br />}20-25 max
<br />(a) (b)
<br />FIGURE 1113-308.2.2
<br />OBSTRUCTED HIGH FORVVARD REACH
<br />10 max J > 10-24 max
<br />254 254-610
<br />(a) (b)
<br />FIGURE 11B-308.3.2
<br />OBSTRUCTED HiGH SIDE REACH
<br />READ. REACH LIMITS
<br />I i
<br />r
<br />17-18 17-19 - -
<br />432-457 432-483
<br />{a) (b)
<br />wheelchair ambulatory
<br />accessible accessible water
<br />water closets closets
<br />FIGURE 11B304.2
<br />WATER CLOSET LOCATION
<br />54 min
<br />1372
<br />poE�
<br />1D
<br />12 max
<br />305
<br />42 min y
<br />1067
<br />24 min �, 0
<br />t 610
<br />7-9
<br />178.229
<br />FIGURE 11B304.7
<br />FiGURE 116304.5.1 DISPENSER OUTLET LOCATION
<br />SIDE WALL GRAB BAR AT WATER CLOSETS
<br />WATER CLOSET AND TOILET COMPARTMENTS
<br />FIGURE 11B-703.4.1
<br />HEIGHT OF TACTILE CHARACTERS
<br />ABOVE FiNISH FLOOR OR GROUND
<br />C X
<br />E E
<br />�t7 cp
<br />t r cr
<br />1
<br />FIGURE 11B-308.2.1
<br />UNOBSTRUCTED FORWARD REACH
<br />56 min_
<br />1422
<br />it
<br />C M 4
<br />Ln
<br />I
<br />t , i
<br />10 max
<br />2%
<br />FIGURE 11B-308,3.1
<br />UNOBSTRUCTED SIDE REACH
<br />i CLEARANCE
<br />t
<br />t
<br />/,?,, DOOR PERMITTED
<br />I TO SWING OVER
<br />HATCHED PORTION
<br />L_---_ ------ -1J J OF MANEUVERING
<br />48 min SPACE
<br />1219
<br />FIGURE 11B-604.3.1
<br />SIZE OF CLEARANCE AT WATER CLOSETS
<br />36 min
<br />24 min r 914 f 12 min
<br />810 305
<br />I
<br />transfer
<br />side
<br />1524
<br />------------------
<br />1 �
<br />1 �
<br />C I I
<br />I �
<br />I I O -
<br />min
<br />810
<br />I 1
<br />I 1
<br />I tm 1
<br />36 min
<br />914
<br />12 min 12 min
<br />305 305
<br />FIGURE 118304.3.2
<br />T -SHAPED TURNING SPACE
<br />48 min
<br />1219
<br />- -------------
<br />-------------� -- - -
<br />'
<br />r
<br />C
<br />N
<br />EN
<br />FIGURE 11B-305.3
<br />CLEAR FLOOR OR GROUND SPACE
<br />7 1 MINIMUM CLEARANCES
<br />610 8
<br />mon
<br />1218
<br />EM
<br />co
<br />lc1; 2
<br />)
<br />max
<br />610
<br />FIGURE 11B-403.5.1
<br />CLEAR WIDTH OF AN ACCESSIBLE ROUTE
<br />1
<br />1:
<br />TECTONIC BUILDERS
<br />CORPORATION
<br />10118 BANDLEY DR. #E,
<br />CUPERTINO, CA 95014
<br />TEL: (408) 216-0804
<br />These drawings and the accompanying specifications are exclusive
<br />property of TECTONIC BUILDERS CORP. written permission is reDuired
<br />by TECTONIC BUILDERS CORP. to re -use or to reproduce these
<br />drawings as specifications by any method in whole or in part. A written
<br />consent is reruired if the drawings are be used by other(s) than assigned
<br />contractor(s). Any Fluestion raised from these drawings should be directed
<br />to TECTONIC BUILDERS CORP. in written format.
<br />REVISIONS BY
<br />RELEASED DATE
<br />11-08-2018 1ST SUBMITTAL
<br />5r_0 ARC �\
<br />Chi
<br />J LARRY L. WANG
<br />C-31807
<br />RENEWAL U31
<br />OF O
<br />C SHEET CONTENTS:
<br />,E M ACCESSIBILITY NOTES
<br />r-------71 ------1
<br />I I I
<br />I I E H I I I
<br />If I
<br />C) I ) I
<br />N I c 1 I
<br />I I
<br />t I
<br />I I
<br />L48 min
<br />1219
<br />30 min
<br />752
<br />(a) (b)
<br />fo rwa rd parallel
<br />FIGURE 118-305.5
<br />POSITION OF CLEAR FLOOR OR GROUND SPACE
<br />kr -------------------i
<br />t I 1
<br />I 1
<br />18 min
<br />I I
<br />EN ' I j 457
<br />I 1i Add 6inches
<br />/ (182 mm) at
<br />exterior stale
<br />of extodor door.
<br />-----------
<br />(a)
<br />front approach, pull side
<br />32 min
<br />(a)
<br />hinged door
<br />FIGURE 118.604.5.2
<br />REAR WALL GRAB BAR AT WATER CLOSETS
<br />8 DOOR CLEARANCES
<br />r--------------
<br />I I
<br />I � I
<br />1 I
<br />12 min
<br />305
<br />I
<br />I
<br />I I
<br />L__ _____----_J
<br />front approach, push side, door
<br />provided with both closer and latch
<br />32 mill 32 min
<br />8' 3 813
<br />(b)
<br />sliding door
<br />FIGURE 11B-404.2.3
<br />CLEAR WIDTH OF DOORWAYS
<br />(C)
<br />folding door
<br />185C Bakery Cafe
<br />85 BAKERY STOCKTO1
<br />875 W. BENJAMIN HOLT DR.,
<br />3 STOCKTON, CA 95207
<br />DRAWN:
<br />CHECKED:
<br />DATE STARTED:
<br />JOB NO.:
<br />SCALE:
<br />FILE NAME:
<br />SHEET NO.:
<br />4
<br />E.C.
<br />L.W.
<br />2018.08.29
<br />AS NOTED
<br />A1.0
<br />APPROVAL STAMP:
<br />
|