COMPLIANCE INFO_1985-2005 - Laserfiche WebLink

Home Browse Search

0 2. If the tank is buried, excavate the portion that contains the riser hole. 3. Remove the bung from the hole and install the riser pipe. I NOTE: The top of the riser pipe must have a 2 x 14 NPT pipe thread or must accept a standard schedule 40 2 x 14 NPT male adaptor ring (supplied in Veeder-Root Kit Number 312020-928). Veeder-Root Riser Cap Kit No. 312020-928 can be used with either a threaded or unthreaded riser pipe. In addition, make sure there will be enough clearance between the top of the installed riser cap and manhole cover to allow room for the two -wire sensor cable to protrude from the cap. 4. Install a standard adaptor ring and/or pipe cap on the riser pipe. ",I NOTE: If the threaded adaptor ring is used, install ,� with the proper adhesive (ie., TBC cement). Use thread sealer, NOT ADHESIVE, when installing the riser cap. C. MONITOR LOCATION SELECTION. WWARNING: IMPROPER SYSTEM OPERATION COULD RESULT IN UNDETECTED POTEN- TIAL ENVIRONMENTAL AND HEALTH HAZ- ARDS IF THE PROBE- OR SENSOR -TO -MONI- TOR WIRE RUNS EXCEED 1000 FEET. RUNS OVER 1000 FEET ARE NOT UL ACCEPTED FOR THIS APPLICATION. PROBE- AND SEN- SOR -TO -MONITOR WIRES MUST NOT EX- CEED 1000 FEET. WARNING: EXPLOSION COULD OCCUR IF THE MONITOR IS INSTALLED IN A VOLA- TILE, COMBUSTIBLE OR EXPLOSIVE (CLASS I, DIVISION I OR DIVISION II) ATMOSPHERE. DO NOT INSTALL THE MONITOR INA VOLA- TILE, COMBUSTIBLE OR EXPLOSIVE ATMO- SPHERE. FAILURE TO COMPLY WITH THESE WARN- INGS COULD RESULT IN DEATH, SERIOUS PERSONAL INJURY, PROPERTY LOSS, AND EQUIPMENT DAMAGE. 1. Select a mounting location on the inside wall of any enclosed building. a. Be sure the console will be protected from severe vibration, extremes in temperature and humidity, rain, and other conditions that could harm the equipment. b. Consider the ease of routing power wiring conduit and probe and sensor conduit to the monitor. c. Be sure the mounting surface material is strong enough to support the monitor's weight. D. POWER WIRING CONDUIT INSTALLATION. To the installer: Read and carefully adhere to the instruc- tions in the following warnings during conduit installation! WARNING: EXPLOSION COULD OCCUR IF OTHER WIRES SHARE CONDUITS OR Site Preparation arAinstallation InstructionsV TLS-JST Monitoring System TROUGHS WITH PROBE OR SENSOR WIR- ING. CONDUITS AND WIRING TROUGHS FROM TLS -350 PROBES AND SENSORS MUST NOT CONTAIN ANY OTHER WIRES. WARNING: EXPLOSION AND/OR EQUIP- MENT DAMAGE COULD OCCUR IF CON- DUITS DO NOT ENTER THE TLS -350 MONI- TOR THROUGH THEIR DESIGNATED PRE- FORMED KNOCKOUTS. FAILURE TO COMPLY WITH THESE WARN- ING COULD RESULT IN DEATH, SERIOUS PERSONAL INJURY, PROPERTY LOSS AND EQUIPMENT DAMAGE. 1. Install rigid metal conduit (3/4", 1" or 1-1/4" I.P.S.) for monitor power from the power panel to the monitor location. Power wiring must enter the monitor through a designated knockout (see Figure 8, "Monitor Dimen- sions and Mounting Requirements"). Power wiring must be installed in conduit separately from probe and sensor wiring. E. PROBE AND SENSOR WIRING CONDUIT IN- STALLATION. To the installer: Read and carefully adhere to the instruc- tions in the following warnings during conduit installation! WARNING: EXPLOSION COULD OCCUR IF OTHER WIRES SHARE CONDUITS OR TROUGHS WITH PROBE OR SENSOR WIR- ING. CONDUITS AND WIRING TROUGHS FROM TLS -350 PROBES AND SENSORS MUST NOT CONTAIN ANY OTHER WIRES. WARNING: EXPLOSION AND/OR EQUIP- MENT DAMAGE COULD OCCUR IF CON- DUITS DO NOT ENTER THE TLS -350 MONI- TOR THROUGH THEIR DESIGNATED PRE- FORMED KNOCKOUTS. FAILURE TO COMPLY WITH THESE WARN- INGS COULD RESULT IN DEATH, SERIOUS PERSONAL INJURY, PROPERTY LOSS AND EQUIPMENT DAMAGE. 1. Wiring between the TLS -350 monitor, probes, and sensors limits the electrical power to the probes and sensors so that there is insufficient energy to ignite fuel. To maintain this safety feature, install TLS -350 probe and sensor wires in separate conduits from all other wiring. NOTE: Wiring from separate TLS probes and TLS sensors may be run in the same conduits or troughs providing they are powered by the same monitor. 6 CAUTION: IMPROPER SYSTEM OPERATION WILL RESULT IF PROBE AND SENSOR WIRING FROM SEPARATE TLS -350 MONITORS SHARE THE SAME CONDUIT. DO NOT RUN PROBE AND SENSOR WIRING FROM SEPARATE TLS - 350 SYSTEMS IN THE SAME CONDUIT. Never run any probe and/or sensor wires in the same conduit or trough as power wires! 2. Install rigid metal conduit (3/a",1" or 1%a") from all probe and sensor locations to the TLS -350 monitor location. The conduit layout should be designed to best suit the