Laserfiche WebLink
Primary Piping System Installation <br /> TABLE 6. 7000 & 8000 Adhesive Kit Data <br /> Approx.No.of Bonds Per Kit(2$^) Working <br /> Kit ID Number Label 2"Quantity 2" 3" 4° Life(2)at <br /> (Excludes Solvent) Colors(') Base Adhesive (50 mm) (75 mm) (100 mm) 75°F(23.9°C) <br /> Minutes <br /> 7014 Red 5.4 oz. (153 grams) 25 18 10 25 <br /> 7024(Twin Pack) Black 2.0 oz.ea.(57 grams ea.) 9/9 6/6 4/4 25 <br /> 70690) Blue 7.8 oz. (221 grams) - - - 25 <br /> 8014 Green 5.5 oz. (156 grams) 21 15 8 15 <br /> 8024(Twin Pack) Yellow 2.3 oz.ea.(65 grams ea.) 9/9 6/6 4/4 15 <br /> 8055(Bag Kit) No Color 1.6 oz. (45 grams) 3 2 1 15 <br /> 8069(3) Orange 8.0 oz. (227 grams) - - I - 15 <br /> (These adhesives are for RED THREAD IIA piping systems conveying petroleum products including leaded and unleaded gasoline, <br /> diesel, 100%ethanol or methanol,all alcohol-gasoline mixtures and biodiesel fuels.) <br /> (')Match the labeled adhesive color to the hardener color before mixing. <br /> (2When adhesive is properly mixed,it has a limited"working life"during which <br /> joints may be bonded. Use of the adhesive beyond the working life is prohibited. <br /> P)Recommended for secondary containment installations due to size of kit. <br /> (")Number of bonds depend on ambient temperature. <br /> ADHESIVE WORKING LIFE <br /> Working life or pot life is the time it takes for the adhesive ADHESIVE DISPOSAL:Once the adhesive and catalyst have <br /> to harden in the mixing can. This time is measured from the been mixed and reacted, nothing can be extracted, and it is <br /> time the adhesive and hardener are first mixed. Working classified as non-hazardous material. Dispose of in a normal <br /> life is shorter at temperatures above 75°F (211C) and manner as other solid waste.Excess adhesive and catalyst can <br /> becomes longer as the temperature drops below 75°F(21°C). be mixed,allowed to react, and disposed of as above. If extra <br /> Working life is affected by the quantity of mixed adhesive cans of adhesive or tubes of catalyst have accumulated with- <br /> out the other component to mix and react, contact your FGS <br /> as well as by temperature. Use the following methods to regional manager.Catalyst tubes,when empty are not subject <br /> increase the working life of adhesives: to EPA regulation and can be disposed of in a normal manner. <br /> These guidelines are based on federal regulations. State and <br /> Warm Weather: local regulations and ordinances should be reviewed. <br /> • Occasionally stir the adhesive mixture during <br /> application. <br /> • Use small ice chests or other containers with freezer <br /> packs to keep adhesive cool. <br /> Cool Weather: <br /> • Store adhesive kits inside. <br /> • Prewarm to between 700-80°F (21.10-26.7°C) before <br /> use. <br /> CAUTION: If adhesive becomes warm and <br /> starts to harden in the container, discard <br /> immediately. DO NOT USE THIS ADHESIVE TO <br /> BOND A JOINT! <br /> When adhesive is allowed to harden in the metal <br /> container,the container may reach approximately 400°F <br /> (2050C). Do not handle hot containers without heavy gloves. <br /> This exothermic reaction will generate a dense,foul-smelling <br /> smoke. Therefore, place the container outdoors in an open <br /> area until it cools. Avoid inhaling smoke. <br /> 7 <br />