Laserfiche WebLink
i <br /> i <br /> URBKZ Environ GDB 10 Stud Traditional Repair Kit <br /> For Existing Flex Pipe from 3.4"to 3.6"OD in Corrugated Ducting repairs <br /> Page 2 <br /> { <br /> STEP 6: Install The Repair Boot <br /> I <br /> Seal around the existing boot &pipe if needed. <br /> • Apply a thick bead of DEB Vail around the sealing surface of the repair boot <br /> • Slide the repair boot over the studs with the fill port at top <br /> • Install the Flange Nut <br /> • Do Not over tighten. -Snug is ok <br /> • Set the Clamp over the pipe end of the repair boot. <br /> You must seal any open <br /> spaces between the pipe j <br /> &CDI and the CDI &the <br /> Corrugated Ducting <br /> Tractional Repair 5ampb8eni4#o7 ger0indraf@cpin8 emries.wrttrews a nine inex�shnpYjT1Ln or 4�Gectbug:A�ce ` ! <br /> ,.Pr e::withezi3tist``6r13rlinnsGDBse7ie netratrdm-fitti <br /> i f : ft. ft Pipe OD DSF II Rill <br /> inches Repair Kit Product Number Clamp Size oz. <br /> 3"DW Vent Pie&3"DW GeoFlex-D 3.57 URBKZ ENV GDB 10-3.6 60 14 <br /> 3"SW Vent Pipe&3"SW GeoFlex-S 3.34 URBKZ ENV GOB 10-3.4 60 15 <br /> 2"DW Vent Pipe&2"DW GeoFlex-D 2.5 URBKZ ENV GDB 10-2.5 40 17 <br /> 2"SW Vent&2"SW GeoFlex-S 2.3 URBKZ ENV GOB 10.2.3 36 17 <br /> 11/2"OW GeoFlex-D 2.0 URBKZ ENV GO810-2.0 32 18 <br /> 11/2"SW GeoFlex-S 1.8 URBKZ ENV GDB 10-1.8 28 19 <br /> 1 <br /> i <br /> Step 10: Fill With DBF II,Insert Fill Plug TOOLS REQUIRED: <br /> • Assemble DAG&DBF II(see instructions on DPM website). Gloves and Static Mixer <br /> • Purge 1-2 oz. 7/16"Nut driver (for flange nuts) <br /> • Fill fitting slowly. 5/16"Nut driver (for Band Clamps) <br /> Note: Use Remote Fill option if access is limited DAG Caulk Gun (for DBF 11) <br /> • Insert fill plug when filling is completed. <br /> DAGP Caulk Gun (Pneumatic version for DBF II} <br /> Clean any spilled DBF II with DEC and dispose DAG III Caulk Gun (for DBB V) <br /> of remaining products per local requirements, ;`:.:> <br /> - - - PRODUCTS NEEDED: <br /> Each OBF 11&DEB V come <br /> Note:After 1 hour T _ --- D C Cleaner with a Static Mixer <br /> B <br /> the repair job may be __- Zip-Tlte Bonder <br /> hydro-static tested - DBF ll Polysulfide Liquid Fill <br /> DEB V Bonder(for Poly or Fiberglass sumps) <br /> FILL Volume: (per repair bootl <br /> Volume of DBF Il needed = See above Chart <br /> Remote Fill Option: Volume of Zip-Tate needed = 3/4 Oz <br /> The following parts are available to order if you can not Volume of DBB V needed = 24 ML <br /> properly position the assembled DBF II applicator gun to parts in kit: <br /> "fill"the repair. The Remote Fill parts provide a flexible Repair Boot,Split URBKZ—x.x (To match pipe size) <br /> extension for the filling process. Corrugated Duct Insert CDIZ-x.x (To match the pipe size) <br /> RF Adapter 24"tube with male&female ends 4 clamps 1#132,1#96,1#72,1 f;xx <br /> RFA Tube-24 %"Tubing in 24"lengths {see chart above) <br /> RFATube i4"Tubing in 200'length roll Fill Port Plug RFAxPIug <br /> RFA TubexTube %"Tube Coupling Repair Instructions <br /> RFA xFemale h"Tube-Female Fill Port end <br /> RFA xMale W Tube-Male Fill Port end <br /> RFA xPlug h"Tube-Male Plug for fill port <br /> Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 34 of 70 <br /> i <br /> I <br /> I <br />