COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

1 SZ Environ FEB 10 Stud "Large Pipe" Repair Kit For Existing Flex or FRP Direct Burial Pipe from 2.7" up to 4.8"00 repairs Page 2 t STEP 7: Field Drill the Plug if needed STEP 8:Install&Bond the Insert or the Drilled Step 9: install The Insert or frilled Plug • Determine if the piping Is straight enough that Plug Back Together 1. Make sure all pasts are cleaned with DBC the insert fit. if it is,use the insert • Wrack Insert or drilled plug around the pipe Cleaner before proceeding • If the insert wont work,measure&drill the App Zip-rite to split area on Insert or plug, 2.Apply Zip•Tite bonder all around the Insert Plug to match the pipe size&the angle of press ends together&clamp with#96 clamp or drilled plug 3.Slide insert or drilled plug into the repair entry. sleeve in the proper position • Split the drilled plug with a knife or saw == _ Parts are 4. If there is any openings around the pipe, wracked seal with DRP repair paste ,f— - around the S.Set the Clamp the around the sleeve&over Plug before _ - pipe the Insert or plug and tighten"snugly". -A , =,Ej I. drilling and _ splitting tziM E =� Parts are bonded& �. clamped - Plug afters G t drilling and ` a I lyvlttSYnt ftepalr CoinponettT5 forPerptndlcUldr&;NdrPerper�tlicuc 7arpipentries in oireet eutiat'appil�tion"sSvithexlsting splitting DB FII 'PJ ia4fiBurf Pipe AD Fill „r -_— __ �'` drutkio - Inches Re air Kit Product Number UIZ insert os. FEB 740pwhen used on 4"LCX 4,8 MSZ ENV FEB 10 4.8 6.0 x 4.8 17 If Ci FEB 7400 for 4"FRP 4.5 MSZ ENV FEB 10-4.5 6.Ox A.S 2i ..; jf U are_Unable to drill € the plilQiltaC �t _ FEB 7400 when used on 3"LCx Pie 3.8 MSZ ENV FEB 10 3.8 6.0 x 3.8 28 = 3"DW Vent Pie &3"DW GeoFlex-D 3.57 MSZ ENV FEB 10 3.6 6.0 x 3.6 30 1 -- 3"FRP 3.5 MSZ ENV FEB 10-3.5 6.0x 3.5 31 =? :: 3"SW Vent Pipe&3"SW GeoRex-S 3.34 MSZ ENV FEB 10-3A 6.0 x 3A 32 �._ MSZ ENV FEB 10 Plu 6.0 x Plug32 _........._.. ..- .-,::.. ..,---- .........::»_......,...:-� P1u verslonforabave f e step 20: Fill with DBF 11,Insert Fill Plug TOOLS REQUIRED: Assemble DAG&DBF II(see instructions on DPM website). Gloves and Static Mixer • Purge 2-2 oz. 7/16"Nut driver (for flange nuts) • Fill fitting slowly. _ 5/16"Nut driver (for Band Clamps) Note: Use Remote Fill option ifaccess is limited DAG Caulk Gun (for DBF II) • Insert fill plug when filling is completed. DAGP Caulk Gun (Pneumatic version for DBF II) • Clean any spilled DBF It with DBC and dispose-._ _, DAG III Caulk Gun (for DBB V) of remaining products per local require - ! PRODUCTS NEEDED: Each DBF it&DBB V come Note After 1 hour = = DBC Cleaner with a Static Mixer the repair job may be Zip-Tits Bonder hydra-static tested _ - DBF it Polysulfide Liquid FIII w: . ,:,_: ..... DBB V Bonder(for Poly or Fiberglass sumps) FILL Volume: (per repair boot} Volume of DBF 11 needed = See Chart Above Remote Fill Option•. Volume of Zip-rite needed = 3/4 Oz The following parts are available to order if you can not Volume of DBB V needed = 24 ML properly position the assembled DBF II applicator gun to Parts in kit: "fill"the repair. The Remote Fill parts provide a flexible Bonding Ring Studded with Cuff URBZ-10-5.8 extension for the filling process. Sleeve USZ-6.04.0 RF Adapter 24"tube with male&female ends Insert UIZ 6.0-x.x(see chart above) RFA Tube-24 W Tubing in 24"lengths plug UI 6.0 Plug RFA Tube %"Tubing in 200'length roll 4 clamps 1#132,3#96 RFA TubexTube W Tube Coupling Fill Port Plug RFA xPlug RFA xFemale W Tube-Female Fill Port end Repair Instructions RFA xMale W Tube-Male Fill Port end RFA xPlug W Tube-Male Plug for fill port Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 46 of 70