Laserfiche WebLink
Multi-Sync Repair Instructions <br /> For Environ Direct Burial Series "10 Stud," Repair Kit <br /> N#Ace Vt..: m 1. to 2.7 <br /> This kit provides the Multi-Sync Repair parts for existing Flex or FRP Pipe fro 8" <br /> APEIall either <br /> V CID In Direct Burial applications where the pipe is coming thru the sump w <br /> straight or at excessive angles. <br /> MSZ ENV FEB 10-XX WARNING:Prepare all surfaces to be bonded prior to completing Installation steps below. <br /> For Environ repairs with Failure to follow each step will void warranty&may result in premature failure of penetration fitting. <br /> Direct Burial Small Pipe This Lit a12121les for rep—al Environ FEB 7000 Serles Harts <br /> Page 1 With piping from 1.8"to 2*7"CID <br /> Rev 3 6-24-20091 <br /> General instructions for CLEANING:Spray all surfaces to be bonded with DBC Cleaner and allow to air dry or wipe excess with a clean dry <br /> cloth. Surfaces must be dry before applying bonder. MPS: Clean,sand and rough up sump surfaces. Clean fitting and <br /> General Instructions for: BONDING TO POLY SUMPS OR FIBERGLASS SU <br /> applypD <br /> _QV between Bonding Ring&sump wall. <br /> STEP 2: Clean all Repair Components P 3: Place&Dry Fit Bonding Ring&sleeve <br /> STEP 1: Loosen Nuts&Pull Back Metal Ring Note:Make sure Bonding Ring is placed with the"Sealing <br /> • Remove Nuts Clean all repair components with DBC Groves"positioned toward the sump wall <br /> • Pull back metal mounting flange&discard prior to Installation <br /> . Place the split bonding ring with Cuff over the pipe with <br /> • Remove outer clampSplit Bonding Cleaner Split the sealing grooves toward the sump wall <br /> • Cut off old boot just beyond the Inner .Ring with Sleeve Place the bonding ring over the studs <br /> clamp&discard Coff <br /> . Place the split sleeve over the pipe&up to the bonding <br /> • Clean off any'paste'or other bonders ring with the fill port up <br /> from around the Environ body&sump <br /> wall, <br /> • Clean&sand sump wall <br /> • Spray Environ Body&sanded sump wall <br /> with DOC cleaner <br /> • If needed patch old boot to seal back wall <br /> Eccentric Insert Mufti-Sync <br /> Reducer <br /> .)F <br /> g <br /> .t.. o <br /> .... ...... <br /> STEP S. install the Bonding Ring STEP 6: Install The Sleeve <br /> Seal around the existing boot &pipe if needed. <br /> Apply D <br /> BB V to the sump side of the Bonding <br /> ju, <br /> k� <br /> Position the sleeve with the fill port at the top <br /> Ring and slide It over the studs&up to the <br /> Rw�km sleeve lined up correctly, <br /> 16 0- Once you have the <br /> sump -T <br /> Thread on the flange nuts. 1.Apply a bead of Zip-rite all around the outer <br /> Note:Tighten the flange nuts"snugly". edges of the bonding ring Cuff <br /> Do not Over-tighten. Snug is ok. 2.Slide sleeve over bonding ring Cuff&snap In <br /> • Wipe any excess RBB V off the bonding ring place(fill port at top) <br /> • Spray DBC onto cloth&wipe clean the outer 3.Set the Clamp,#96,the around the sleeve& <br /> edges of the bonding ring. over the bonding ring and tighten'Snugly". <br /> DOB V goes on <br /> STEP 4: Bond Sleeve&Bonding Ring �"grooved"side <br /> • Apply Zip-Tite to the split bonding ring. <br /> toward sump <br /> Use 2 of the clamps,#132&96,to hold in <br /> place while curing. <br /> • Apply Zip-Tite to the split sleeve and use 2 <br /> clamps,#96,to hold In place while <br /> curing. <br /> • Leave these clamps In place for approx 30 <br /> minutes for curing before proceeding to Zip-Tite here <br /> the next step <br /> You must seal any open spaces between the <br /> pipe &the old Environ boot <br /> FY. <br /> Fill porton top <br /> -.4 <br /> Sleeve in place over"Cuff"with clamp <br /> • <br /> 7 1 __R <br /> Bon n n place: <br /> Wipe any excess D BB V from outer edge Page 47 of 70 <br /> Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 <br />