COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

i SZ Environ FEB 10 Stud "Small Pipe" Repair Kit For Existing Flex or FRP Direct Burial Pipe from 1.8"to 2.7"OD repairs Page 2 1 STEP 7:install&Band Eccentric insert&Multi- Step 8: Install The Eccentric insert&Multi-Sync Reducer • Dry fit the Eccentric insert.Make sure it fits properly over the Sync Reducer Back Together pipe&inside the sleeve. • Wrack Eccentric Insert around the pipe • Dry fit the Multi-Sync Reducer • Wrack Multi-Sync Reducer around the pipe . Adjust the positions so that they lineup properly with the Repair - • Apply Zip-Tete to split area on Eccentric Inse Sleeve&Pipe. _ press ends together&clamp Note: A proper fit will not cause extra pressure or force to the - - • Apply Zap-rite to split area on Multi-Sync sleeve and will allow a longer lasting repair. Reducer,press ends together&clamp Once you have the part lined up correctly 1.Pull back the Mufti-Sync Reducer&Eccentric insert = i 2.Apply Zip-rite bonder all around the Eccentric Insert, 3.Slide Eccentric into the Repair sleeve in the proper position "- 4.Apply Zip-lite bonder all around the Multi-Sync Reducer I - - S.Slide the Multi-Sync Reducer into it's proper place 6.Set the Clamp the around the sleeve&over the Eccentric _ - - Insert and tighten"snugly". 7.Set damp over reducer end on the pipe&tighten enough to i i create a seal around the pipe. i.. I Parts are wracked around the pipe - — l entries is I1iret-Bur�dLap�ratinnsyQitff ezistiri$ N7utff3yoffeiXcbnpaDents For Per�tlldicuT�r&rPerpe�tlCcuiar PrQrsS Eitulroat FEB r5E&se setratibtrfitthn Pipe OD s n _ ,. _ •--�- - e0g -&, "jury' � Fill! Repair Kit Product Number Clam SheOBa=1 - 2"LCX 2.7 MSZ ENV FEB 10-2.7 44 37 j 2"DW Vent&2"DW Geoflex-D 2.5 MSZ ENV FEB 10.2.5 40 38 i _ 2"FRP 2.315 MSZ ENV FEB 10-2.4 40 39 _..:. 2"SW Vent&2"SW GeoFlex-S 2.3 MSZ ENV FEB 10-2.3 36 40 DW GeoFlex-D 2-0 M52 ENV FEB 10.2.0 32 41 11 "Steel 1.9 MSZ ENV FEB 10-1.9 32 42 Parts are bonded&clamped 1112-SW GeoFlex-S 1.8 MSZ ENV FEB 10-1.8 28 42 Step 9: Fill With DBF 11,Insert Fill Plug TOOLS RE 1R D: • Assemble DAG&DBF Ii(see instructions on DPM website). Gloves and Static Mixer • Purge s-2 oz. _ 7/16"Nut driver (for flange nuts) • Fill fitting slowly. 5/16"Nut driver (for Band Clamps) 1 Note: Use Remote Fill option if access is limited " _ = DAG Caulk Gun (for DBF 11) j • Insert fill plug when filling is completed. DAGP Caulk Gun (Pneumatic version for DBF 11} j • Clean any spilled DBF 11 with DBC and dispose; _ DAG III Caulk Gun (for DBB V) of remaining products per local requirements:.`_':..; PRODUCTS NEEDED' Each DBF 11&D88 V come Note:After i hour DBC Cleaner with a Static Mixer the repair job may be __ = Zip-Tate Bonder hydro-static tested - DBF II Polysulfide Liquid Fill p -• ' •--- DBB V Bonder(for Poly or Fiberglass sum s) c c- P. FILL Volume•1=292111§29_11 Volume of DBF 11 needed = See Chart Above Remote Fill Option: Volume of Zip Tite needed = 3/4 Oz The following parts are available to order if you can not Volume of DBB V needed = 24 ML properly position the assembled DBF II applicator gun to Parts In kit: "fill"the repair. The Remote Fill parts provide a flexible Bonding Ring Studded with Cuff URBZ-10-5.8 extension for the filling process. Sleeve USZ-6.0x6.0 RF Adapter 24"tube with male&female ends Eccentric Insert UIZ 6.Ox4.5E RFA Tube-24 W Tubing in 24"lengths Multi-Sync Reducer URZ MS 4.5-x.x(to match pipe size) RFA Tube W Tubing in 200'length roll 6 clamps 1#132,3#96,1#72,1#xx RFA TubexTube %"Tube Coupling (See Chart Above) RFA xFemale W Tube-Female Fill Port end Fill Port Plug RFA xPlug RFA xMale %"Tube-Male Fill Port end Repair instructions RFA xPlug %"Tube-Male Plug for fill port Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 48 of 70