COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

1 I 1 _ l Multi-Sync Repair InstructionsAD f rDP For Environ FEB 3100 Series Repair Kit U E:M:4;aR uM) This Kit provides the Multi-Sync Repair parts for 1"Environ Flex Pipe,1"or%"Rigid Steel M* RSRF conduits in applications where the conduit pipe is coming thru the sump wall either straight or at excessive angles. For PVC coated conduits and conduits smaller than Y4",consult the MSZ ENV 3100-X.X factory. For Environ Conduit Repairs WARNING:Prepare all surfaces to be bonded prior to completing installation steps below. Page 1 Failure to follow each step will void warranty&may result In premature failure of penetration fitting. Rev 2- 6-22-2009 This Kit applies to repairing• Environ FEB 815? 3100 3075 &3050 parts General Instructions for: CLEANING:Spray all surfaces to be bonded with DBC Cleaner and allow to air dry or wipe excess with a clean dry cloth. Surfaces must be dry before applying bonder. General instructions for: BONDING TO POLY SUMPS OR FIBERGLASS SUMPS: Clean,sand and rough up sump surfaces. Clean fitting and apply 268 V between Bonding Ring&sump wall. On Poly Sumps if sump wall is un-even use DRP in place of DBB V. STEP Z: Clean all Repair Components STEP 3: Place&Dry Fit Bonding Ring&Sleeve STEP 1: Loosen&Clean Mounting Plata Clean all repair components DBC Note: Make sure Bonding Ring is placed over the studs s w • Remove clamp on the reducer at the pipe between the sump wall&the mounting plate,with • Remove the nuts from the mounting plate prior to installation "Sealing Groves"positioned toward the sump wail and • Pull back the mounting plate Cleanertit the split part of the bonding ring toward the top • Clean off any'paste'or other bonders Split Sp Place the split bonding ring over the studs,between from around old Environ body&sump Bonding SleeveRina the sump wall&the metal plate with the sealing wall, grooves toward the sump wall. • Seal up any cracks or ri in rubber boot * Rx• Snug up the metal plate with a couple of flange nuts m o Place the split sleeve over the pipe&Up to the • Clean&sand sump wail • Spray Environ body&sanded sump wall i' bonding ring with the fill port up - If everything fits properly,then loosen the nuts&pull with DBC cleaner p= = back the mounting plate again to bond the parts s together. - I Eccentric insertMulti-Sync i Reducer VN You must seal any open spacefF between the pipe &old boot area 1 STEP S. Install Bonding Ring&Mounting Plate STEP 6: Install The Sleeve '.If est@trth6rlg fi#S Ct�ttieu� `-v Apply DBB V to the sump side of the Bonding Seal around old boot&pipe,if needed —x_..-.... ,.�� ,� A'�;� '1'i�� =:-�' Ring and slide it over the studs&up to the Slide in the sleeve with the fits port at the op. sump wall DO NOT push the sleeve over the snap ring ��x9Ekl once you you have the sleeve lined up correctly, ��- -- Slide in the mounting plate _ Reinstall the flange nuts.Tighten snugly 1.Pull back the sleeve a little • Reinstall the pipe clamp on the old boot 2.Apply a bead of DBB IIl all around the outer Note: Do not Over-tighten. Snug is ok edges of the bonding ring • Wipe any excess DBB V off the bonding ring 3.Slide sleeve over bonding ring&snap in place • Spray DBC onto cloth&wipe clean the outer (fill port at top) 4 Set the Clamp the around the sleeve&over " _.:_........::.... . edges of the bonding ring. the bonding ring and tighten"snugly". STEP 4: Bond Sleeve&Bonding Ring • Apply DBB Ill to split bonding ring. Use 1 -6- of the clamps to hold in place while curing. o • Apply DBB ill to the split sleeve and use 2 _ clamps to hold in place while curing. • Leave these clamps in place for approx 30 minutes for curing before proceeding to D88 V goes on"grooved" the next step side toward sump DBB 111 here Fill port on top Bonding Ring in place. Sleeve in place with clamp Old clamp in place + Wipe any excess DBB V from outer edge . Diversified Products Manufacturing Inc. 5523 Baggett Marysville Road,Oroville,CA 95965 530-534-3966 www.dpm-Ilc.com