Laserfiche WebLink
MS ENV FEB 3100 Series <br /> For Environ Series 3100 Conduit repairs <br /> Page 2 <br /> step 9: install The Eccentric insert&Muld-sync Reducer mark the <br /> STEP 7:Install&Bond Eccentric Insert&Multi- - Dry fit the Eccentric insert.Make sure it fits properly alignment <br /> Sync Reducer Back Together over the pipe&Inside the sleeve. <br /> • Wrack Eccentric Insert around the pipe . Dry fit the Mutti-Sync Reducer <br /> • Wrack Multi-Sync Reducer around the pipe - Adjust the positions so that they lineup properly with <br /> • Apply DBB III to split area on Eccentric Insert, the Repair Sleeve&Pipe. <br /> &clamp pressure or force to <br /> press ends together Note:A proper fit wilt not cause extra <br /> • <br /> Apply DBB III to split area on Multi-Sync the sleeve and will allow a longer lasting repair. <br /> Reducer,press ends together&clamp once you have the part lined up correctly <br /> 1. Pull back the Multi-Sync Reducer&Eccentric Insert <br /> 2.Apply DBB III bonder all around the Eccentric Insert, <br /> 3.Slide Eccentric Into the Repair sleeve in the proper <br /> position <br /> 4.Apply DBB III bonder all around the Multi-Sync <br /> Reducer <br /> S.Slide the multi-Sync Reducer into it's proper place <br /> 6.Set the Clamp the around the sleeve&over the <br /> Eccentric insert and tighten"snugly". <br /> 7.Set clamp over reducer end on the pipe&tighten <br /> enough to create a seal around the pipe. <br /> Parts are wracked around the pipe <br /> .i ez <br /> n <br /> L Pi <br /> eoD Clamp DEF 11 <br /> JJ1gW.,& <br /> -P__ product Number h4e Fill*z <br /> r 1 DW rJ Inches Ir <br /> FEB 3150 <br /> 1.45 MSZ ENV FEB 3150 <br /> 2 12 <br /> —ri- 20 <br /> 12 <br /> d Conduit 1.315 M5Z ENV FEB 3157 20 <br /> 13 <br /> FEB-3075 for 3/47 GeoFlex D Pipe 1.18 Consult FactoIfi 14 <br /> IAH 1 <br /> FEB-3075 for 3/4"111-1 11 Conduit LOS MSZ ENV FEB 3157 <br /> Parts are bonded&clamped FEB 3050 7-RigidCondult 0.84 MSZ ENV FEB 3050 16 14 <br /> 'A <br /> TOOLS UOk1KD- <br /> Step 10: Fill With DBF 11,Insert Fill Plug Gloves and Static Mixer <br /> - Assemble DAG&DBF 11(see instructions on DPM website). 5/16"Nut driver (for Band Clamps) <br /> - Purge a maximum of 2 oz DAG Caulk Gun (for DBF 11) <br /> - Fill fitting slowly. DAGP Caulk Gun (Pneumatic version for DBF 11 <br /> - insert fill plug when filling Is completed. DAG III Caulk Gun (for DBB V) <br /> e Clean any spilled DBF 11 with DBC and dispose <br /> of remaining products per local requirements. <br /> ptODUCTS NEEDED; <br /> DEC Cleaner Each DBE II&DBB Vcome <br /> DBB III Bonder with a Static Mixer <br /> Note:After I hour <br /> the repair jab may be DBF 11 Polysulfide Liquid Fill <br /> hydro-static tested DBBV Bonder(for Poly or Fiberglass SUMPS) <br /> FILL Volume:IgSLr.Sggk_b_0211 <br /> Volume of DBF 11 needed = See Chart Above <br /> Volume of DEB III needed = 1/2 Oz <br /> Volume of DBB V needed = 13 IVIL <br /> Remote Fill option: Pares iakit; <br /> The following parts are available to order if you can not Bonding Ring UIZ-MS-4.5X2.5-2.3 <br /> properly position the assembled DBF 11 applicator gun to Sleeve USZ-4.5x4.5 <br /> "fill"the repair. The Remote Fill parts provide a flexible Eccentric Insert UIZ-4.5x3.61! <br /> extension for the filling process. Multi-sync Reducer U RZ-3.6x XX(To match the pipe size) <br /> RIF Adapter 24"tube with male&female ends 5 clamps 3#72,1#60,1#xx(see chart above) <br /> RFATube-24 W Tubing in 24"lengths Fill Port Plug RFAxPlug <br /> RFATube W Tubing in 200'length roll Repair Instructions <br /> RFATubexTube Y2"Tube Coupling <br /> RFA xFemale %"Tube-Female Fill Port end <br /> RFA xMale X"Tube-Male Fill Port end <br /> RFA xPlug W Tube-Male Plug for fill port -11C <br /> Diversified Products Manufacturing Inc. 5523 Baggett Marysville Road,Oroville,CA 95965 530-534-3966 www.dpm -com <br />