WORK PLANS - Laserfiche WebLink

Home Browse Search

ACCESSIBILITY REQUIREMENTS A. APPLICATION AND ADMINISTRATION 32. EDGE OF SIGNS OR OTHER OBJECTS, WHEN MOUNTED ON POSTS OR PYLONS WITH THEIR BOTTOM EDGES 22. WHERE HANDRAILS ARE PROVIDED ALONG WALKING SURFACES WITH RUNNING SLOPES NOT STEEPER THAN 58. WHERE DOORWAYS ARE LOCATED ADJACENT TO A RAMP LANDING, MANEUVERING CLEARANCES REQUIRED BY HANDRAILS 1. ALL AREAS OF NEWLY DESIGNED AND NEWLY CONSTRUCTED BUILDINGS AND FACILITIES AND ALTERED LESS THAN 80 INCHES ABOVE THE FLOOR OR GROUND SURFACE, SHALL BE ROUNDED OR EASED AND THE 1:20 (5%) THEY SHALL COMPLY WITH HANDRAIL REQUIREMENTS OF 1113-505 HANDRAILS. §11B-403.6 I 1113-404.2.4 AND 1113-404.3.2 SHALL BE PERMITTED TO OVERLAP THE REQUIRED LANDING AREA. DOORS, WHEN PORTIONS OF EXISTING BUILDINGS AND FACILITIES SHALL COMPLY WITH THESE REQUIREMENTS. THESE CORNERS SHALL HAVE A MINIMUM RADIUS OF '/e INCH. §11B-307.3.1 FULLY OPEN, SHALL NOT REDUCE THE REQUIRED RAMP LANDING WIDTH BY MORE THAN 3 INCHES. DOORS, IN 27. HANDRAILS PROVIDED ALONG WALKING SURFACES COMPLYING WITH SECTION 116-403 WALKING SURFACES, t%03- 3- IV REQUIREMENTS APPLY TO TEMPORARY AND PERMANENT BUILDINGS AND FACILITIES. 11 B-201 33. VERTICAL CLEARANCE SHALL BE AT LEAST 80 INCHES HIGH ON CIRCULATION PATHS EXCEPT AT DOOR 23. ALL WALKS WITH CONTINUOUS GRADIENTS SHALL HAVE RESTING AREAS, 5 FEET IN LENGTH, AT INTERVALS ANY POSITION, SHALL NOT REDUCE THE MINIMUM DIMENSION OF THE RAMP LANDING TO LESS THAN 42 INCHES. REQUIRED AT RAMPS COMPLYING WITH SECTION 11B-405 RAMPS, AND REQUIRED AT STAIRS COMPLYING WITH § CLOSERS AND DOOR STOPS, WHICH MAY BE 78 INCHES MINIMUM ABOVE THE FINISH FLOOR OR GROUND. OF 400 FEET MAXIMUM. THE RESTING AREA SHALL BE AT LEAST AS WIDE AS THE WALK. THE SLOPE OF THE §11 B-405.7.5 SECTION 11 B-504 STAIRWAYS SHALL COMPLY WITH SECTION 11 B-505 HANDRAILS. §11 B-505.1 2. EACH ADDITION TO AN EXISTING BUILDING OR FACILITY SHALL COMPLY WITH THE REQUIREMENTS FOR NEW §11 B-307.4 RESTING AREA IN ALL DIRECTIONS SHALL BE 1:48 (2.083%) MAXIMUM. §11B-403.7 CONSTRUCTION AND SHALL COMPLY WITH 11 B-202.4 PATH OF TRAVEL REQUIREMENTS. §11 B-202.2 34. GUARDRAILS OR OTHER BARRIERS WITH A LEADING EDGE LOCATED 27 INCHES MAXIMUM ABOVE THE FINISH 59. RAMP RUNS SHALL HAVE COMPLIANT HANDRAILS PER 11 B-505 HANDRAILS. §11 B-405.8 28. HANDRAILS SHALL BE PROVIDED ON BOTH SIDES OF STAIRS AND RAMPS. §11 B-505.2 WPO FLOOR OR GROUND SHALL BE PROVIDED WHERE THE VERTICAL CLEARANCE ON CIRCULATION PATHS IS LESS DOORS, DOORWAYS AND GATES 3. EACH EXISTING ELEMENT OR SPACE THAT IS ALTERED SHALL COMPLY WITH THE APPLICABLE REQUIREMENTS THAN 80 INCHES HIGH. §11 B-307.4, FIGURE 11 B-307.4 60. EDGE PROTECTION COMPLYING WITH 11 B-405.9.2 CURB OR BARRIER SHALL BE PROVIDED ON EACH SIDE 29. HANDRAILS SHALL BE CONTINUOUS WITHIN THE FULL LENGTH OF EACH STAIR FLIGHT OR RAMP RUN. INSIDE OF DIVISION 2, INCLUDING 11 B-202.4 PATH OF TRAVEL REQUIREMENTS UNLESS THE BUILDING OFFICIAL 35. WHERE A GUY SUPPORT IS USED PARALLEL TO A CIRCULATION PATH, INCLUDING BUT NOT LIMITED TO 24. DOORS, DOORWAYS, AND GATES PROVIDING USER PASSAGE SHALL BE PROVIDED IN ACCORDANCE WITH OF RAMP RUNS AND AT EACH SIDE OF RAMP LANDINGS. §11 B-405.9 (SEE EXCEPTIONS) HANDRAILS ON SWITCHBACK OR DOGLEG STAIRS AND RAMPS SHALL BE CONTINUOUS BETWEEN FLIGHTS OR DETERMINES COMPLIANCE WITH APPLICABLE REQUIREMENTS IS TECHNICALLY INFEASIBLE AND THE ALTERATION SIDEWALKS, A GUY BRACE, SIDEWALK GUY OR SIMILAR DEVICE SHALL BE USED TO PREVENT AN OVERHANGING 11 B-206.5 DOORS, DOORWAYS, AND GATES. §11 B-206.5 RUNS. §11B-505.3 COMPLIES WITH THE REQUIREMENTS TO THE MAXIMUM EXTENT FEASIBLE OR PROVIDES EQUIVALENT FACILITATION. OBSTRUCTION. §11B-307.4 61. A CURB, 2 INCHES HIGH MINIMUM, OR BARRIER SHALL BE PROVIDED THAT PREVENTS THE PASSAGE OF A 4 §11 B-202.3 REACH RANGES 25. EACH ENTRANCE TO A BUILDING OR FACILITY REQUIRED TO COMPLY WITH 11 B-206.4 ENTRANCES SHALL INCH DIAMETER SPHERE, WHERE ANY PORTION OF THE SPHERE IS WITHIN 4 INCHES OF THE FINISH FLOOR OR 30. TOP OF GRIPPING SURFACES OF HANDRAILS SHALL BE 34 INCHES MINIMUM AND 38 INCHES MAXIMUM COMPLY WITH 11B-404 DOORS, DOORWAYS, AND GATES. §11B-206.5.1 GROUND SURFACE. TO PREVENT WHEEL ENTRAPMENT, THE CURB OR BARRIER SHALL PROVIDE A CONTINUOUS VERTICALLY ABOVE WALKING SURFACES, STAIR NOSINGS, AND RAMP SURFACES. HANDRAILS SHALL BE AT A SJB Brands, LLC 36. ELECTRICAL CONTROLS AND SWITCHES INTENDED TO BE USED BY THE OCCUPANT OF A ROOM OR AREA TO AND UNINTERRUPTED BARRIER ALONG THE LENGTH OF THE RAMP. §11B-405.9.2 CONSISTENT HEIGHT ABOVE WALKING SURFACES, STAIR NOSINGS, AND RAMP SURFACES. §11B-505.4 17915 SKY PARK CIRCLE, SUITE J, 4. WHEN ALTERATIONS OR ADDITIONS ARE MADE TO EXISTING BUILDINGS OR FACILITIES, AN ACCESSIBLE PATH OF CONTROL LIGHTING AND RECEPTACLE OUTLETS, APPLIANCES OR COOLING, HEATING AND VENTILATING EQUIPMENT 26. WITHIN A BUILDING OR FACILITY, EVERY DOOR, DOORWAY OR GATE SERVING ROOMS AND SPACES COMPLYING IRVINE, CA 92614 TRAVEL TO THE SPECIFIC AREA OF ALTERATION OR ADDITION SHALL BE PROVIDED UNLESS OTHERWISE EXEMPT. SHALL BE LOCATED WITHIN ALLOWABLE REACH RANGES. LOW REACH SHALL BE MEASURED TO THE BOTTOM OF WITH THIS CHAPTER SHALL COMPLY WITH 11 B-404 DOORS, DOORWAYS, AND GATES. §11 B-206.5.2 62. LANDINGS SUBJECT TO WET CONDITIONS SHALL BE DESIGNED TO PREVENT THE ACCUMULATION OF WATER. 31. CLEARANCE BETWEEN HANDRAIL GRIPPING SURFACES AND ADJACENT SURFACES SHALL BE 11h INCHES T _ THE OUTLET BOX AND HIGH REACH SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX. §11 B-308.1.1 §11 B-405.10 MINIMUM. HANDRAILS MAY BE LOCATED IN A RECESS IF THE RECESS IS 3 INCHES MAXIMUM DEEP AND 18 EL. (949)475 0146 §11 B-202.4 27. DOORS, DOORWAYS AND GATES THAT ARE PART OF AN ACCESSIBLE ROUTE SHALL COMPLY WITH 11 B-404 INCHES MINIMUM CLEAR ABOVE THE TOP OF THE HANDRAIL. §11 B-505.5 FAX:(949)475-0137 5. PRIMARY ACCESSIBLE PATH OF TRAVEL SHALL INCLUDE A PRIMARY ENTRANCE TO THE BUILDING OR FACILITY; 37. ELECTRICAL RECEPTACLE OUTLETS ON BRANCH CIRCUITS OF 30 AMPERES OR LESS AND COMMUNICATION DOORS, DOORWAYS, AND GATES. §11 B-404.1 TOILET AND BATHING FACILITIES SERVING THE AREA; DRINKING FOUNTAINS SERVING THE AREA; PUBLIC SYSTEM RECEPTACLES SHALL BE LOCATED WITHIN ALLOWABLE REACH RANGES. LOW REACH SHALL BE MEASURED D. GENERAL SITE AND BUILDING ELEMENTS 32. HANDRAIL GRIPPING SURFACES SHALL BE CONTINUOUS ALONG THEIR LENGTH AND SHALL NOT BE TELEPHONES SERVING THE AREA, AND SIGNS. §11B-202.4 TO THE BOTTOM OF THE OUTLET BOX AND HIGH REACH SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX. 28. MANUAL DOORS AND DOORWAYS AND MANUAL GATES INTENDED FOR USER PASSAGE SHALL COMPLY WITH PARKING SPACES OBSTRUCTED ALONG THEIR TOPS OR SIDES. THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL NOT BE §11 B-308.1.2 11 B-404.2 MANUAL DOORS, DOORWAYS, AND MANUAL GATES. §11 B-404.2 OBSTRUCTED FOR MORE THAN 20 PERCENT OF THEIR LENGTH. WHERE PROVIDED, HORIZONTAL PROJECTIONS THESE DRAWINGS AND SPECIFICATIONS AND IDEAS, DESIGNS AND 1. WHERE PARKING SPACES ARE PROVIDED, ACCESSIBLE PARKING SPACES SHALL BE PROVIDED IN NUMBER AND SHALL OCCUR 1�,h INCHES MINIMUM BELOW THE BOTTOM OF THE HANDRAIL GRIPPING SURFACE. §11 B-505.6 ARRANGEMENTS REPRESENTED THEREBY ARE AND SHALL REMAIN THE B. BUILDING BLOCKS 38. HIGH FORWARD REACH THAT IS UNOBSTRUCTED SHALL BE 48 INCHES MAXIMUM AND THE LOW FORWARD 29. REVOLVING DOORS, REVOLVING GATES, AND TURNSTILES SHALL NOT BE PART OF AN ACCESSIBLE ROUTE. KIND REQUIRED PER SECTION 1113-208 PARKING SPACES. §11B-208.1 THEREOF SHA L BE COPED, DISCLOSED ASSOCIATES;Y OF GARY WANG & NOAR TO OTHERS OR NO DIN FLOOR OR GROUND SURFACES REACH SHALL BE 15 INCHES MINIMUM ABOVE THE FINISH FLOOR OR GROUND. §11B-308.2.1, FIGURE §11B-402.2.1 33. HANDRAIL GRIPPING SURFACES WITH A CIRCULAR CROSS SECTION SHALL HAVE AN OUTSIDE DIAMETER OF 1% CONNECTION WITH ANY WORK OR PROJECT OTHER THAN THE 11 B-308.2.1 2. PROVIDE ACCESSIBLE SPACES FOR EACH PARKING FACILITY (PARKING LOTS AND PARKING STRUCTURES). THE INCHES MINIMUM AND 2 INCHES MAXIMUM. §11 B-505.7.1 SPECIFIC PROJECT FOR WHICH THEY HAVE BEEN PREPARED AND 1. FLOOR AND GROUND SURFACES SHALL BE STABLE, FIRM, AND SLIP RESISTANT. §11 B-302.1 30. AT LEAST ONE OF THE ACTIVE LEAVES OF DOORWAYS WITH TWO LEAVES SHALL COMPLY WITH 11 B-404.2.3 NUMBER OF PARKING SPACES REQUIRED TO BE ACCESSIBLE IS TO BE CALCULATED SEPARATELY FOR EACH DEVELOPED WITHOUT THE WRITTEN CONSENT OF GARY WANG & 39. HIGH FORWARD REACH SHALL BE 48 INCHES MAXIMUM WHERE THE REACH DEPTH IS 20 INCHES OR LESSCLEAR WIDTH AND 11B-404.2.4 MANEUVERING CLEARANCES. §11B-404.2.2 PARKING FACILITY; THE REQUIRED NUMBER IS NOT BASED ON THE TOTAL NUMBER OF PARKING SPACES 34. HANDRAIL GRIPPING SURFACES WITH ANON-CIRCULAR CROSS SECTION SHALL HAVE A PERIMETER DIMENSION ASSOCIATES. VISUAL CONTACT WITH THESE DRAWINGS AND AND 44 INCHES MAXIMUM WHERE THE REACH DEPTH EXCEEDS 20 INCHES. HIGH FORWARD REACH SHALL NOT SPECIFICATIONS SHALL CONSTITUTE CONCLUSIVE EVIDENCE OF 2. CARPET OR CARPET TILE SHALL BE SECURELY ATTACHED AND SHALL HAVE A FIRM CUSHION, PAD, OR PROVIDED IN ALL OF THE PARKING FACILITIES PROVIDED ON SITE. §1113-208 OF 4 INCHES MINIMUM AND 6/a INCHES MAXIMUM, AND A CROSS-SECTION DIMENSION OF 2% INCHES MAXIMUM. THESE RESTRICTIONS. WRITTEN DIMENSIONS ON THESE DRAWINGS BACKING OR NO CUSHION OR PAD. CARPET OR CARPET TILE SHALL HAVE A LEVEL LOOP, TEXTURED LOOP, EXCEED 25 INCHES IN DEPTH. §11B-308.2.2, FIGURE 1113-308.2.2 31. DOOR OPENINGS SHALL PROVIDE A CLEAR WIDTH OF 32 INCHES MINIMUM. CLEAR OPENINGS OF DOORWAYS §11 B-505.7.2 SHALL HAVE PRECEDENCE OVER SCALED DIMENSIONS; LEVEL CUT PILE, OR LEVEL CUT UNCUT PILE TEXTURE. PILE HEIGHT SHALL BE �lh INCH MAXIMUM. §11B-302.2, WITH SWINGING DOORS SHALL BE MEASURED BETWEEN THE FACE OF THE DOOR AND THE STOP, WITH THE DOOR 3. ONE IN EVERY SIX OR FRACTION OF SIX PARKING SPACES REQUIRED BY SECTION 11 B-208.2 MINIMUM CONTRACTORS SHALL VERIFY, AND BE RESPONSIBLE FOR ALL / 40. WHERE A HIGH FORWARD REACH IS OVER AN OBSTRUCTION, THE CLEAR FLOOR SPACE SHALL EXTEND OPEN 90 DEGREES. OPENINGS MORE THAN 24 INCHES DEEP SHALL PROVIDE A CLEAR OPENING OF 36 INCHES NUMBER, BUT NOT LESS THAN ONE, SHALL BE SERVED BY AN ACCESS AISLE 96 INCHES WIDE MINIMUM PLACED 35. HANDRAIL GRIPPING SURFACES AND ANY SURFACES ADJACENT TO THEM SHALL BE FREE OF SHARP OR DIMENSIONS AND CONDITIONS ON THE JOB, AND THIS OFFICE FIGURE 11 B-302.2 BENEATH THE ELEMENT FOR A DISTANCE NOT LESS THAN THE REQUIRED REACH DEPTH OVER THE OBSTRUCTION. MINIMUM. THERE SHALL BE NO PROJECTIONS INTO THE REQUIRED CLEAR OPENING WIDTH LOWER THAN 34 MUST BE NOTIFIED OF ANY VARIATIONS FROM THE DIMENSIONS §11 ATH T22 INCHES ABOVE THE FINISH FLOOR OR GROUNDPROJECTIONS INTO THE CLEAR OPENING WIDTH BETWEEN 34 ON THE SIDE OPPOSITE THE DRIVER'S SIDE WHEN THE VEHICLE IS GOING FORWARD INTO THE PARKING SPACE ABRASIVE ELEMENTS AND SHALL HAVE ROUNDED EDGES. §11 B-505.8 AND CONDITIONS SHOWN BY THESE DRAWINGS. SHOP DETAIL MUST 3. EXPOSED EDGES OF CARPET SHALL BE FASTENED TO FLOOR SURFACES AND SHALL HAVE TRIM ON THE . . AND SHALL BE DESIGNATED "VAN ACCESSIBLE". ALL SUCH SPACES MAY BE GROUPED ON ONE LEVEL OF A BE SUBMITTED TO THIS OFFICE FOR REVIEW BEFORE PROCEEDING ENTIRE LENGTH OF THE EXPOSED EDGE. CARPET EDGE TRIM SHALL COMPLY WITH 11 B-303 CHANGES IN LEVEL. INCHES AND 80 INCHES ABOVE THE FINISH FLOOR OR GROUND SHALL NOT EXCEED 4 INCHES. §11B-404.2.3 PARKING STRUCTURE. §11B-208.2.4, 1113-502, FIG 11B-502, 118-502.3, & 1113-502.3.3 36. HANDRAILS SHALL NOT ROTATE WITHIN THEIR FITTINGS. §1113-505.9 WITH THE FABRICATION. §11 B-302.2 41. HIGH SIDE REACH SHALL BE 48 INCHES MAXIMUM AND THE LOW SIDE REACH SHALL BE 15 INCHES MINIMUM ABOVE THE FINISH FLOOR WHERE THE SIDE REACH IS UNOBSTRUCTED OR THE DEPTH OF ANY 32. MINIMUM MANEUVERING CLEARANCES AT DOORS AND GATES SHALL COMPLY WITH 1113-404.2.4 MANEUVERING 4. ACCESSIBLE PARKING SPACES COMPLYING WITH SECTION 1113-502 PARKING SPACES SERVING A PARTICULAR 37. HANDRAIL GRIPPING SURFACES SHALL EXTEND BEYOND AND IN THE SAME DIRECTION OF STAIR FLIGHTS AND 4. OPENINGS IN FLOOR OR GROUND SURFACES SHALL NOT ALLOW PASSAGE OF A SPHERE MORE THAN lh INCH OBSTRUCTION DOES NOT EXCEED 10 INCHES. §11B-308.3.1, FIGURE 1113-308.3.1 CLEARANCES. MANEUVERING CLEARANCES SHALL EXTEND THE FULL WIDTH OF THE DOORWAY AND THE REQUIRED BUILDING OR FACILITY SHALL BE LOCATED ON THE SHORTEST ACCESSIBLE ROUTE OF TRAVEL FROM ADJACENT RAMP RUNS IN ACCORDANCE WITH SECTION 1113-505.10 HANDRAIL EXTENSIONS. §11B-505.10 ARCHITECT IN DIAMETER. ELONGATED OPENINGS SHALL BE PLACED SO THAT THE LONG DIMENSION IS PERPENDICULAR TO LATCH SIDE OR HINGE SIDE CLEARANCE. §11B-404.2.4 PARKING TO AN ACCESSIBLE ENTRANCE (AS NEAR AS PRACTICAL TO AN ACCESSIBLE ENTRANCE). §11B-208.3.1 42. HIGH SIDE REACH SHALL BE 46 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND WHERE THE HIGH THE DOMINANT DIRECTION OF TRAVEL. §11 B-302.3, FIGURE 11 B-302.3 SIDE REACH IS OVER AN OBSTRUCTION MORE THAN 10 INCHES BUT NOT MORE THAN 24 INCHES IN DEPTH. 33. SWINGING DOORS AND GATES SHALL HAVE MANEUVERING CLEARANCES COMPLYING WITH TABLE 38. RAMP HANDRAILS SHALL EXTEND HORIZONTALLY ABOVE THE LANDING FOR 12 INCHES MINIMUM BEYOND THE §11 B-308.3.2, FIGURE 11 B-308.3.2 11 B-404 5. IN BUILDINGS WITH MULTIPLE ACCESSIBLE ENTRANCES WITH ADJACENT PARKING, ACCESSIBLE PARKING SPACES TOP AND BOTTOM OF RAMP RUNS. EXTENSIONS SHALL RETURN TO A WALL, GUARD, OR THE LANDING SURFACE, CHANGES IN LEVEL .2.4.1. §11 B-404.2.4.1 COMPLYING WITH SECTION 1113-502 PARKING SPACES SHALL BE DISPERSED AND LOCATED CLOSEST TO THE OR SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT RAMP RUN. §11B-505.10.1 4 5. VERTICAL CHANGES IN LEVEL FOR FLOOR OR GROUND SURFACES MAY BE Y4 INCH HIGH MAXIMUM AND 43. OBSTRUCTIONS FOR HIGH SIDE REACH SHALL NOT EXCEED 34 INCHES IN HEIGHT AND 24 INCHES IN DEPTH. 34. DOORWAYS LESS THAN 36 INCHES WIDE WITHOUT DOORS OR GATES, SLIDING DOORS, OR FOLDING DOORS ACCESSIBLE ENTRANCES. §11B-208.3.1 39. AT THE TOP OF A STAIR FLIGHT, HANDRAILS SHALL EXTEND HORIZONTALLY ABOVE THE LANDING FOR 12 GARY WANG i §11B-308.3.2, FIGURE 11 . . , B-30832 SHALL HAVE MANEUVERING CLEARANCES COMPLYING WITH TABLE 11B-404.2.4.2.. . . . .2. §11 B-404242 . . . 6. IN PARKING FACILITIES THAT DO NOT SERVE A PARTICULAR BUILDING OR FACILITY, ACCESSIBLE PARKING INCHES MINIMUM BEGINNING DIRECTLY ABOVE THE FIRST RISER NOSING. EXTENSIONS SHALL RETURN TO A WALL, WITHOUT EDGE TREATMENT. CHANGES IN LEVEL GREATER THAN /a INCH AND NOT EXCEEDING INCH IN &ASSOCIATES, INC. HEIGHT SHALL BE BEVELED WITH A SLOPE NOT STEEPER THAN 1:2. §1113-303, FIGURES 1113-303.2 & SPACES COMPLYING WITH SECTION 1113-502 PARKING SPACES SHALL BE LOCATED ON THE SHORTEST GUARD, OR THE LANDING SURFACE, OR SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT STAIR a OPERABLE PARTS 35. MANEUVERING CLEARANCES FOR FORWARD APPROACH SHALL BE PROVIDED WHEN ANY OBSTRUCTION WITHIN ACCESSIBLE ROUTE OF TRAVEL TO AN ACCESSIBLE PEDESTRIAN ENTRANCE OF THE PARKING FACILITY. FLIGHT. §11B-505.10.2 1 1 B-303.3 18 INCHES OF THE LATCH SIDE AN INTERIOR DOORWAY, OR WITHIN 24 INCHES OF THE LATCH SIDE OF AN §11 B-208.3.1 44. OPERABLE PARTS ON ACCESSIBLE ELEMENTS, ACCESSIBLE ROUTES, AND IN ACCESSIBLE ROOMS AND SPACES EXTERIOR DOORWAY, PROJECTS MORE THAN 8 INCHES BEYOND THE FACE OF THE DOOR, MEASURED 1000 Corporate Center 4 Suite 550 40. AT THE BOTTOM OF A STAIR FLIGHT, HANDRAILS SHALL EXTEND AT THE SLOPE OF THE STAIR FLIGHT FOR Monterey Park, CA 91754 6. CHANGES IN LEVEL GREATER THAN % INCH IN HEIGHT SHALL BE RAMPED AND SHALL COMPLY WITH THE SHALL BE PROVIDED A CLEAR FLOOR OR GROUND SPACE COMPLYING WITH 11 B-305 CLEAR FLOOR OR GROUND PERPENDICULAR TO THE FACE OF THE DOOR OR GATE. §11 B-404.2.4.3 RESIDENTIAL FACILITIES: HORIZONTAL DISTANCE EQUAL TO ONE TREAD DEPTH BEYOND THE LAST RISER NOSING. SUCH EXTENSION SHALL TEL: 2 2 - FAX: 2 7 -71 1 REQUIREMENTS OF 1113-405 RAMPS OR 1113-406 CURB RAMPS AS APPLICABLE. §11B-303 SPACE AND BE PLACED WITHIN ONE OR MORE OF THE REACH RANGES SPECIFIED IN 1113-308 REACH RANGES. CONTINUE WITH A HORIZONTAL EXTENSION OR SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT STAIR (6 6) 88 6898 (6 6) 68 0 §11B-309.2 36. FLOOR OR GROUND SURFACE WITHIN REQUIRED MANEUVERING CLEARANCES SHALL COMPLY WITH1113-302 FLIGHT OR SHALL RETURN TO A WALL, GUARD, OR THE WALKING SURFACE. AT THE BOTTOM OF A STAIR FLIGHT, http://www.garywang.com 7. ABRUPT CHANGES IN LEVEL EXCEEDING 4 INCHES IN A VERTICAL DIMENSION BETWEEN WALKS, SIDEWALKS OR FLOOR OR GROUND SURFACES. CHANGES IN LEVEL ARE NOT PERMITTED AT DOOR LANDINGS. §11 B-404.2.4.4 8. WHERE PARKING SPACES ARE MARKED WITH LINES, WIDTH MEASUREMENTS OF PARKING SPACES AND ACCESS A HORIZONTAL EXTENSION OF A HANDRAIL SHALL BE 12 INCHES LONG MINIMUM AND A HEIGHT EQUAL TO THAT OTHER PEDESTRIAN WAYS AND ADJACENT SURFACES OR FEATURES SHALL BE IDENTIFIED BY WARNING CURBS AT 45. OPERABLE PARTS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, AISLES SHALL BE MADE FROM THE CENTERLINE OF THE MARKINGS.] §11 B-502.1 (SEE EXCEPTIONS) OF THE SLOPING PORTION OF THE HANDRAIL AS MEASURED ABOVE THE STAIR NOSINGS. EXTENSION SHALL LEAST 6 INCHES IN HEIGHT ABOVE THE WALK OR SIDEWALK SURFACE OR BY GUARDS OR HANDRAILS WITH A PINCHING, OR TWISTING OF THE WRIST. FORCE REQUIRED TO ACTIVATE OPERABLE PARTS SHALL BE 5 POUNDS 37. THRESHOLDS, IF PROVIDED AT DOORWAYS, SHALL BE ilh INCH HIGH MAXIMUM. RAISED THRESHOLDS AND RETURN TO A WALL, GUARD, OR THE LANDING SURFACE, OR SHALL BE CONTINUOUS TO THE HANDRAIL OF AN GUIDE RAIL CENTERED 2 INCHES MINIMUM AND 4 INCHES MAXIMUM ABOVE THE SURFACE OF THE WALK OR MAXIMUM. §11B-309.4 CHANGES IN LEVEL AT DOORWAYS SHALL COMPLY WITH 11 B-302 FLOOR OR GROUND SURFACES AND 11 B-303 9. DIMENSION MINIMUM 18 FOOT LONG CAR AND VAN ACCESSIBLE PARKING SPACE(S) AND ACCESS AISLE(S). ADJACENT STAIR FLIGHT. §11 B-505.10.3 SIDEWALK. THESE REQUIREMENTS DO NOT APPLY BETWEEN A WALK OR SIDEWALK AND AN ADJACENT STREET OR CHANGES IN LEVEL. §11B-404.2.5. §11B-502.2, FIGURES 1113-502.2 AND 11B-502.3 STAMP DRIVEWAY. §11B-303.5 46. ELEMENTS THAT ARE EXEMPT FROM ALL REQUIREMENTS FOR OPERABLE PARTS REQUIREMENTS INCLUDE E. PLUMBING FIXTURES AND FACILITIES ELECTRICAL OR COMMUNICATION RECEPTACLES SERVING A DEDICATED USE; FLOOR ELECTRICAL RECEPTACLES; 38. THE DISTANCE BETWEEN TWO HINGED OR PIVOTED DOORS IN SERIES AND GATES IN SERIES SHALL BE 48 10. DIMENSION MINIMUM 9 FOOT WIDTH AT ACCESSIBLE CAR PARKING SPACE. §11B-502.2, FIG. 1113-502.2 & TURNING SPACE HVAC DIFFUSERS, EXERCISE MACHINES AND EXERCISE EQUIPMENT AND THOSE OPERABLE PARTS INTENDED FOR INCHES MINIMUM PLUS THE WIDTH OF DOORS OR GATES SWINGING INTO THE SPACE. §11B-404.2.6 FIG. 11 B-502.3 DRINKING FOUNTAINS USE ONLY BY SERVICE OR MAINTENANCE PERSONNEL. §1113-205.1 8. TURNING SPACES SHALL MEET THE REQUIREMENTS OF 11B-302 FLOOR OR GROUND SURFACES EXCEPT THAT 39. HANDLES, PULLS, LATCHES, LOCKS, AND OTHER OPERABLE PARTS ON DOORS AND GATES SHALL COMPLY CHANGES IN LEVEL ARE NOT PERMITTED. TURNING SPACES SHALL BE EITHER CIRCULAR OR T-SHAPED. DOORS 11. DIMENSION MINIMUM 12 FOOT WIDE ACCESSIBLE VAN PARKING SPACE WITH MINIMUM 5 FOOT WIDE ACCESS 1. WHERE TOILET FACILITIES AND BATHING FACILITIES ARE PROVIDED, THEY SHALL COMPLY WITH 1113-213 TOILET 47. EXCEPT FOR LIGHT SWITCHES, WHERE REDUNDANT CONTROLS ARE PROVIDED FOR A SINGLE ELEMENT, ONE WITH 1113-309.4 OPERATION. OPERABLE PARTS OF SUCH HARDWARE SHALL BE 34 INCHES MINIMUM AND 44 AISLE. VAN PARKING SPACES SHALL BE PERMITTED TO BE MINIMUM 9 FEET WIDE WHERE ACCESS AISLE IS 8 FACILITIES AND BATHING FACILITIES. WHERE TOILET FACILITIES AND BATHING FACILITIES ARE PROVIDED IN MAY SWING INTO TURNING SPACES. §1113-304 CONTROL IN EACH SPACE SHALL NOT BE REQUIRED TO COMPLY WITH SECTION 1113-309 OPERABLE PARTS. INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. WHERE SLIDING DOORS ARE IN THE FULLY OPEN FOOT WIDE MINIMUM. §11B-502.2, FIGURES 1113-502.2 AND 1113-502.3 FACILITIES PERMITTED BY 11B-206.2.3 MULTI-STORY BUILDINGS AND FACILITIES EXCEPTIONS 1 AND 2 NOT TO �SE� ARCy/ 9. CIRCULAR TURNING SPACES SHALL BE A SPACE OF 60 INCHES DIAMETER MINIMUM AND MAY INCLUDE KNEE §11 B-205.1 POSITION, OPERATING HARDWARE SHALL BE EXPOSED AND USABLE FROM BOTH SIDES. §11B-404.2.7 CONNECT STORIES BY AN ACCESSIBLE ROUTE, TOILET FACILITIES AND BATHING FACILITIES SHALL BE PROVIDED ON `{ H• �� AND TOE CLEARANCE COMPLYING WITH 118-306 KNEE AND TOE CLEARANCE. §11 B-304.3.1 12. CAR AND VAN STALL ACCESS AISLE SHALL BE 5 FOOT WIDE MINIMUM AND SHALL ADJOIN AN ACCESSIBLE A STORY CONNECTED BY AN ACCESSIBLE ROUTE TO AN ACCESSIBLE ENTRANCE. §11 B-213.1 V 40. DOOR AND GATE CLOSING SPEED SHALL COMPLY WITH THE FOLLOWING: ROUTE. TWO PARKING SPACES SHALL BE PERMITTED TO SHARE A COMMON ACCESS AISLE. §11B-502.3, FIGURES C. ACCESSIBLE ROUTES 1113-502.2 AND 1113-502.3 2. WHERE SEPARATE TOILET FACILITIES ARE PROVIDED FOR THE EXCLUSIVE USE OF SEPARATE USER GROUPS, * �.d, 10. T-SHAPED TURNING SPACES SHALL BE A T-SHAPED SPACE WITHIN A 60 INCH SQUARE MINIMUM WITH ARMS A. DOOR CLOSERS AND GATE CLOSERS SHALL BE ADJUSTED SO THAT FROM AN OPEN POSITION OF 90 THE TOILET FACILITIES SERVING EACH USER GROUP SHALL COMPLY WITH 11 B-213 TOILET FACILITIES AND RE ,D4-3 - 619 AND BASE 36 INCHES WIDE MINIMUM. EACH ARM OF THE T SHALL BE CLEAR OF OBSTRUCTIONS 12 INCHES WHERE REQUIRED DEGREES, THE TIME REQUIRED TO MOVE THE DOOR TO A POSITION OF 12 DEGREES FROM THE LATCH IS 5 cP� _ _Q MINIMUM IN EACH DIRECTION AND THE BASE SHALL BE CLEAR OF OBSTRUCTIONS 24 INCHES MINIMUM. 13. ACCESS AISLES SHALL EXTEND THE FULL REQUIRED LENGTH OF THE PARKING SPACES THEY SERVE. BATHING FACILITIES. §11 B-213.1.1 SECONDS MINIMUM. §11 B-404.2.8.1 §11 B-502.3.2 & FIG. 11 B-502.3 §11B-304.3.2, FIGURE 1113-304.3.2 1. AT LEAST ONE ACCESSIBLE ROUTE SHALL BE PROVIDED WITHIN THE SITE FROM ACCESSIBLE PARKING SPACES 3. WHERE TOILET ROOMS ARE PROVIDED, EACH TOILET ROOM SHALL COMPLY WITH 1113-603 TOILET AND 97� ' FO�� AND ACCESSIBLE PASSENGER LOADING ZONES; PUBLIC STREETS AND SIDEWALKS; AND PUBLIC TRANSPORTATION B. DOOR AND GATE SPRING HINGES SHALL BE ADJUSTED SO THAT FROM THE OPEN POSITION OF 70 DEGREES, 14. ACCESS AISLES SHALL BE MARKED WITH A BLUE PAINTED BORDERLINE AROUND THEIR PERIMETER. THE AREA BATHING ROOMS. WHERE BATHING ROOMS ARE PROVIDED, EACH BATHING ROOM SHALL COMPLY WITH 1113-603 OF CAL\ 11. T-SHAPED TURNING SPACES MAY INCLUDE KNEE AND TOE CLEARANCE COMPLYING WITH 11 B-306 KNEE STOPS TO THE ACCESSIBLE BUILDING OR FACILITY ENTRANCE THEY SERVE. WHERE MORE THAN ONE ROUTE IS THE DOOR OR GATE SHALL MOVE TO THE CLOSED POSITION IN 1.5 SECONDS MINIMUM. §11B-404.2.8.2 WITHIN THE BLUE BORDERLINES SHALL BE MARKED WITH HATCHED LINES A MAXIMUM OF 36 INCHES ON CENTER TOILET AND BATHING ROOMS. §11 B-213.2 SEE EXCEPTIONS AND TOE CLEARANCE ONLY AT THE END OF EITHER THE BASE OR ONE ARM. §1 1 B-304.3.2 PROVIDED, ALL ROUTES MUST BE ACCESSIBLE. §11B-206.2.1 (SEE EXCEPTIONS) IN A COLOR CONTRASTING WITH THAT OF THE AISLE SURFACE, PREFERABLY BLUE OR WHITE. THE WORDS "NO CLEAR FLOOR OR GROUND SPACE 41. THE FORCE FOR PUSHING OR PULLING OPEN A DOOR OR GATE OTHER THAN FIRE DOORS SHALL BE AS 4. UNISEX TOILET ROOMS SHALL CONTAIN NOT MORE THAN ONE LAVATORY, AND NOT MORE THAN TWO WATER 2. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE BUILDINGS, ACCESSIBLE FACILITIES, PARKING" SHALL BE PAINTED ON THE SURFACE WITHIN EACH ACCESS AISLE IN WHITE LETTERS A MINIMUM OF 12 FOLLOWS: §11 B-404.2.9 INCHES IN HEIGHT AND LOCATED TO BE VISIBLE FROM THE ADJACENT VEHICULAR WAY. ACCESS AISLE MARKINGS CLOSETS WITHOUT URINALS OR ONE WATER CLOSET AND ONE URINAL. UNISEX BATHING ROOMS SHALL CONTAIN 12. CLEAR FLOOR OR GROUND SPACES SHALL MEET THE REQUIREMENTS OF 1113-302 FLOOR OR GROUND ACCESSIBLE ELEMENTS, AND ACCESSIBLE SPACES THAT ARE ON THE SAME SITE. §11B-206.2.2 (SEE EXCEPTION) MAY EXTEND BEYOND THE MINIMUM REQUIRED LENGTH. §11B-502.3.3, FIGURE 1113-502.3.3 ONE SHOWER OR ONE SHOWER AND ONE BATHTUB, ONE LAVATORY, AND ONE WATER CLOSET. DOORS TO UNISEX A. INTERIOR HINGED DOORS AND GATES: 5 POUNDS MAXIMUM. TOILET ROOMS AND UNISEX BATHING ROOMS SHALL HAVE PRIVACY LATCHES. §11 B-213.2.1 SURFACES AND SHALL NOT HAVE CHANGES IN LEVEL EXCEPT FOR SLOPES NOT STEEPER THAN 1:48 (2.083%). 3. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT EACH STORY AND MEZZANINE IN MULTI-STORY BUILDINGS 15. ACCESS AISLES SHALL NOT OVERLAP THE VEHICULAR WAY. ACCESS AISLES SHALL BE PERMITTED TO BE PROJECT NAME/ADDRESS: §11 B-305 AND FACILITIES. §11 B-206.2.3 (SEE EXCEPTIONS) B. SLIDING OR FOLDING DOORS: 5 POUNDS MAXIMUM. 5. PLUMBING FIXTURES AND ACCESSORIES PROVIDED IN A TOILET ROOM OR BATHING ROOM REQUIRED TO PLACED ON EITHER SIDE OF THE PARKING SPACE EXCEPT FOR VAN PARKING SPACES WHICH SHALL HAVE COMPLY WITH 11 B-213.2 TOILET AND BATHING ROOMS SHALL COMPLY WITH 11 B-213.3 PLUMBING FIXTURES 13. CLEAR FLOOR OR GROUND SPACE SHALL BE 30 INCHES MINIMUM BY 48 INCHES MINIMUM. §11B-305.3, 4. IN ALTERATIONS AND ADDITIONS, WHERE AN ESCALATOR OR STAIR IS PROVIDED WHERE NONE EXISTED C. REQUIRED FIRE DOORS: THE MINIMUM OPENING FORCE ALLOWABLE BY THE APPROPRIATE ADMINISTRATIVE ACCESS AISLES LOCATED ON THE PASSENGER SIDE OF THE PARKING SPACES. §11B-502.3.4 AND ACCESSORIES. §11B-213.3 FIGURE 11 B-305.3 PREVIOUSLY AND MAJOR STRUCTURAL MODIFICATIONS ARE NECESSARY FOR THE INSTALLATION, AN ACCESSIBLE AUTHORITY, NOT TO EXCEED 15 POUNDS. JUICE IT U P! ROUTE SHALL BE PROVIDED BETWEEN THE LEVELS SERVED BY THE ESCALATOR OR STAIR. §11B-206.2.3.1 SEE 16. PARKING SPACES AND ACCESS AISLES SERVING THEM SHALL COMPLY WITH SECTION 11 B-302 FLOOR OR ( GROUND SURFACES. ACCESS AISLES SHALL BE AT THE SAME LEVEL AS THE PARKING SPACES THEY SERVE. 6. DOOR SHALL NOT SWING INTO THE CLEAR FLOOR SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. OTHER ROUTEONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR OR GROUND SPACE SHALL ADJOIN AN ACCESSIBLE EXCEPTIONS) D. EXTERIOR HINGED DOORS: 5 POUNDS MAXIMUM. THAN THE DOOR TO THE ACCESSIBLE WATER CLOSET COMPARTMENT, A DOOR IN ANY POSITION, MAY ENCROACH RIPON TOWN SQUARE ROUTE OR ADJOIN ANOTHER CLEAR FLOOR OR GROUND SPACE. §11 B-305.6 CHANGES IN LEVEL ARE NOT PERMITTED. §11B-502.4 INTO THE TURNING SPACE BY 12 INCHES MAXIMUM. §11 B-603.2.3 5. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE BUILDING OR FACILITY ENTRANCES WITH ALL 42. SWINGING DOOR AND GATE SURFACES WITHIN 10 INCHES OF THE FINISH FLOOR OR GROUND MEASURED 15. CLEAR FLOOR OR GROUND SPACE SHALL BE POSITIONED FOR EITHER FORWARD OR PARALLEL APPROACH TO ACCESSIBLE SPACES AND ELEMENTS WITHIN THE BUILDING OR FACILITY, INCLUDING MEZZANINES, WHICH ARE VERTICALLY SHALL HAVE A SMOOTH SURFACE ON THE PUSH SIDE EXTENDING THE FULL WIDTH OF THE DOOR OR 17. CLEARLY SHOW MINIMUM VERTICAL CLEARANCE OF 8 FEET 2 INCHES AT ACCESSIBLE PARKING SPACES AND 7 AT TOILET BATHING ROOMS, P N INTO T 1201 W. MAIN ST. AN ELEMENT UNLESS OTHERWISE SPECIFIED. §11 B-305.5, FIGURE 11 B-305.5 GATE. PARTS CREATING HORIZONTAL OR VERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN 1/16 INCH OF ALONG AT LEAST ONE VEHICLE ACCESS ROUTE TO SUCH SPACES FROM SITE ENTRANCES AND EXITS. 2 SINGLE USER 0 LET OR B T G 00 S, DOORS SHALL BE PERMITTED TO SWIG 0 HE CLEAR OTHERWISE CONNECTED BY A CIRCULATION PATH. §1113-206.2.4 (SEE EXCEPTIONS) THE SAME PLANE AS THE OTHER AND BE FREE OF SHARP OR ABRASIVE EDGES. CAVITIES CREATED BY ADDED §116-502.5 FLOOR SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE ONLY IFA 30 INCH BY 48 INCH MINIMUM CLEAR RIPON, CA 95366 16. CLEAR FLOOR OR GROUND SPACE MAY INCLUDE KNEE AND TOE CLEARANCE COMPLYING WITH 1113-306 KICK PLATES SHALL BE CAPPED. §11 B-404.2.10 FLOOR SPACE IS PROVIDED WITHIN THE ROOM BEYOND THE ARC OF THE DOOR SWING. §11 B-603.2.3 6. ACCESSIBLE ROUTES SHALL COINCIDE WITH OR BE LOCATED IN THE SAME AREA AS GENERAL CIRCULATION KNEE AND TOE CLEARANCE UNLESS OTHERWISE SPECIFIED. §11 B-305.4 PATHS. WHERE CIRCULATION PATHS ARE INTERIOR, REQUIRED ACCESSIBLE ROUTES SHALL ALSO BE INTERIOR; AN SIGNAGE EXCEPTION ACCESSIBLE ROUTE SHALL NOT PASS THROUGH KITCHENS, STORAGE ROOMS, RESTROOMS, CLOSETS OR OTHER 43. DOORS, GATES, AND SIDE LIGHTS ADJACENT TO DOORS OR GATES, CONTAINING ONE OR MORE GLAZING 8. MIRRORS LOCATED ABOVE THE LAVATORIES OR COUNTERTOPS SHALL BE INSTALLED WITHIN THE BOTTOM EDGE 17. ALCOVES SHALL BE 36 INCHES WIDE MINIMUM IF THEIR DEPTH EXCEEDS 24 INCHES AND THEY PROVIDE PANELS THAT PERMIT VIEWING THROUGH THE PANELS SHALL HAVE THE BOTTOM OF AT LEAST ONE GLAZED 18. PARKING SPACE IDENTIFICATION SIGNS SHALL INCLUDE THE INTERNATIONAL SYMBOL OF ACCESSIBILITY (ISA) SPACES USED FOR SIMILAR PURPOSES, EXCEPT AS PERMITTED BY CHAPTER 10. §11 B-206.3 OF THE REFLECTING SURFACE 40 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. MIRRORS NOT CLEAR FLOOR OR GROUND SPACE FOR A FORWARD APPROACH. §11B-305.7, FIGURE 1113-305.7.1 PANEL LOCATED 43 INCHES MAXIMUM ABOVE THE FINISH FLOOR. §11B-404.2.11 COMPLYING WITH SECTION 11B-703.7.2.1 ISA. §11B-502.6, FIGURE 11B-703.7.2.1 LOCATED ABOVE THE LAVATORIES OR COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE REVISIONS: 7. IN RESTAURANTS, CAFETERIAS, BANQUET FACILITIES, BARS, AND SIMILAR FACILITIES, AN ACCESSIBLE ROUTE REFLECTING SURFACE 35 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. §11B-603.3 18. ALCOVES SHALL BE 60 INCHES WIDE MINIMUM IF THEIR DEPTH EXCEEDS 15 INCHES AND THEY PROVIDE SHALL BE PROVIDED TO ALL FUNCTIONAL AREAS, INCLUDING RAISED OR SUNKEN AREAS, AND OUTDOOR AREAS. 44. FULL-POWERED AUTOMATIC DOORS SHALL COMPLY WITH ANSI/BHMA A156.10. LOW-ENERGY AND 19. SIGNS IDENTIFYING VAN PARKING SPACES SHALL CONTAIN ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN Q1 - CLEAR FLOOR OR GROUND SPACE FOR A PARALLEL APPROACH. §11B-305.7, FIGURE 1113-305.7.2 §11 B-206.2.5 POWER-ASSISTED DOORS SHALL COMPLY WITH ANSI/BHMA A156.19. AUTOMATIC DOORS AND AUTOMATIC GATES WITH THE DESIGNATION "VAN ACCESSIBLE." SIGNS SHALL BE 60 INCHES MINIMUM ABOVE THE FINISH FLOOR OR 9• COAT HOOKS SHALL BE LOCATED WITHIN ONE OF THE REACH RANGES SPECIFIED IN SECTION 1113-308. 0 - SHALL COMPLY WITH THE FOLLOWING: §11B-404.3 GROUND SURFACE MEASURED TO THE BOTTOM OF THE SIGN. §11B-502.6 SHELVES SHALL BE LOCATED 40 INCHES MINIMUM AND 48 INCHES MAXIMUM ABOVE THE FINISH FLOOR. KNEE AND TOE CLEARANCE 8. COMMON USE CIRCULATION PATHS WITHIN EMPLOYEE WORK AREAS SHALL COMPLY WITH 11B-402 ACCESSIBLE A. DOORWAYS SHALL PROVIDE A CLEAR OPENING OF MEDICINE CABINETS SHALL BE LOCATED WITH A USABLE SHELF NO HIGHER THAN 44 INCHES MAXIMUM ABOVE 0 - ROUTES. §11B-206.2.8 (SEE EXCEPTIONS) 32 INCHES MINIMUM IN POWER-ON AND POWER-OFF MODE. THE MINIMUM CLEAR WIDTH FOR AUTOMATIC DOOR 20. PARKING IDENTIFICATION SIGNS SHALL BE REFLECTORIZED WITH A MINIMUM AREA OF 70 SQUARE INCHES. THE FINISH FLOOR. §11B-603.4 Al - 19. FOR LAVATORIES AND BUILT-IN DINING AND WORK SURFACES REQUIRED TO BE ACCESSIBLE, TOE CLEARANCE SYSTEMS IN A DOORWAY SHALL PROVIDE A CLEAR, UNOBSTRUCTED OPENING OF 32 INCHES WITH ONE LEAF §11 B-502.6.1 SHALL BE PROVIDED THAT IS 30 INCHES IN WIDTH AND 9 INCHES IN HEIGHT ABOVE THE FINISH FLOOR OR ENTRANCES POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED POSITION. §11 B-404.3.1 10. WHERE TOWEL OR SANITARY NAPKIN DISPENSERS, WASTE RECEPTACLES, OR OTHER ACCESSORIES ARE 0 - GROUND FOR A DEPTH OF 19 INCHES MINIMUM. §11 B-306.2.1 B. CLEARANCES AT POWER-ASSISTED DOORS AND GATES SHALL COMPLY WITH 1113-404.2.4 MANEUVERING 21. ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN BELOW THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL PROVIDED IN TOILET FACILITIES, AT LEAST ONE OF EACH TYPE SHALL BE LOCATED ON AN ACCESSIBLE ROUTE. 6 - 9. ENTRANCES SHALL BE PROVIDED IN ACCORDANCE WITH 11B-206.4 ENTRANCES. ENTRANCE DOORS, CLEARANCES. CLEARANCES AT AUTOMATIC DOORS AND GATES WITHOUT STANDBY POWER AND SERVING AN STATE "MINIMUM FINE $250." §11 B-502.6.2 ALL OPERABLE PARTS, INCLUDING COIN SLOTS, SHALL BE 40 INCHES MAXIMUM ABOVE THE FINISH FLOOR. 20. FOR ELEMENTS REQUIRED TO PROVIDE TOE CLEARANCE OTHER THAN LAVATORIES AND BUILT-IN DINING AND DOORWAYS, AND GATES SHALL COMPLY WITH 11 B-404 DOORS, DOORWAYS, AND GATES AND SHALL BE ON AN ACCESSIBLE MEANS OF EGRESS SHALL COMPLY WITH 11 B-404.2.4 MANEUVERING CLEARANCES. §11 B-404.3.2 §11 B-603.5 0 - WORK SURFACES, TOE CLEARANCE SHALL BE PROVIDED THAT IS 30 INCHES IN WIDTH AND 9 INCHES IN HEIGHT ACCESSIBLE ROUTE COMPLYING WITH 11 B-402 ACCESSIBLE ROUTES; (SEE EXCEPTIONS). §11 B-206.4 C. THRESHOLDS AND CHANGES IN LEVEL AT DOORWAYS SHALL COMPLY WITH 11 B-404.2.5 THRESHOLDS. 22. A PARKING SPACE IDENTIFICATION SIGN SHALL BE VISIBLE FROM EACH PARKING SPACE. SIGNS SHALL BE ABOVE THE FINISH FLOOR OR GROUND FOR A DEPTH OF 17 INCHES MINIMUM UNDER ELEMENTS REQUIRED TO §11 PERMANENTLY POSTED EITHER IMMEDIATELY ADJACENT TO THE PARKING SPACE OR WITHIN THE PROJECTED BE ACCESSIBLE. §116-306.2.3 10. ALL ENTRANCES AND EXTERIOR GROUND-FLOOR EXITS TO BUILDINGS AND FACILITIES SHALL COMPLY WITH D. DOORSOORS 3.3 IN SERIES AND GATES IN SERIES SHALL COMPLY WITH 1113-404.2.6 DOORS IN SERIES AND GATES IN PARKING SPACE WIDTH AT THE HEAD END OF THE PARKING SPACE. SIGNS MAY ALSO BE PERMANENTLY POSTED 11. THE WATER CLOSET SHALL BE POSITIONED WITH A WALL OR PARTITION TO THE REAR AND TO ONE SIDE. ISSUE DATE: 11 B-404 DOORS, DOORWAYS, AND GATES. §11 B-206.4.1 SERIES. §11B-404.3 ON A WALL AT THE INTERIOR END OF THE PARKING SPACE. §11B-502.6.3 THE CENTERLINE OF THE WATER CLOSET SHALL BE 17 INCHES MINIMUM TO 18 INCHES MAXIMUM FROM THE 21. SPACE EXTENDING GREATER THAN 6 INCHES BEYOND THE AVAILABLE KNEE CLEARANCE AT 9 INCHES ABOVE E. MANUALLY OPERATED CONTROLS SHALL COMPLY WITH 1113-309 OPERABLE PARTS. THE CLEAR FLOOR SPACE SIDE WALL OR PARTITION, EXCEPT THAT THE WATER CLOSET SHALL BE 17 INCHES MINIMUM AND 19 INCHES - THE FINISH FLOOR OR GROUND SHALL NOT BE CONSIDERED TOE CLEARANCE. §11B-306.2.4 11. WHERE DIRECT ACCESS IS PROVIDED FOR PEDESTRIANS FROM A PARKING STRUCTURE TO A BUILDING OR ADJACENT TO THE CONTROL SHALL BE LOCATED BEYOND THE ARC OF THE DOOR SWING. §116-404.3.5 23. EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVE SURFACE IDENTIFICATION COMPLYING WITH EITHER OF MAXIMUM FROM THE SIDE WALL OR PARTITION IN THE AMBULATORY ACCESSIBLE TOILET COMPARTMENT SPECIFIED 1ST FACILITY ENTRANCE, EACH DIRECT ACCESS TO THE BUILDING OR FACILITY ENTRANCE SHALL COMPLY WITH F. WHERE DOORS AND GATES WITHOUT STANDBY POWER ARE A PART OF A MEANS OF EGRESS, THE CLEAR THE FOLLOWING SCHEMES: §11B-502.6.4 IN SECTION 11 B-604.8.2 AMBULATORY ACCESSIBLE COMPARTMENTS. WATER CLOSETS SHALL BE ARRANGED FOR 2ND - 22. TOE CLEARANCE SHALL EXTEND 19 INCHES MAXIMUM UNDER LAVATORIES FOR TOILET AND BATHING 11 B-404 DOORS, DOORWAYS, AND GATES. §11 B-206.4.2 BREAK OUT OPENING AT SWINGING OR SLIDING DOORS AND GATES SHALL BE 32 INCHES MINIMUM WHEN A LEFT-HAND OR RIGHT-HAND APPROACH. §11B-604.2 3RD - FACILITIES AND 25 INCHES MAXIMUM UNDER OTHER ELEMENTS. §11B-306.2.2 OPERATED IN EMERGENCY MODE. §116-404.3.6 A. THE PARKING SPACE SHALL BE MARKED WITH AN INTERNATIONAL SYMBOL OF ACCESSIBILITY (ISA) COMPLYING 12. EXCEPT SELF-SERVICE STORAGE FACILITIES, ALL ENTRANCES TO EACH TENANCY IN A FACILITY SHALL G. REVOLVING DOORS, REVOLVING GATES, AND TURNSTILES SHALL NOT BE PART OF AN ACCESSIBLE ROUTE. WITH SECTION 11B-703.7.2.1 ISA IN WHITE ON A BLUE BACKGROUND A MINIMUM 36 INCHES WIDE BY 36 12. CLEARANCE AROUND A WATER CLOSET SHALL BE 60 INCHES MINIMUM MEASURED PERPENDICULAR FROM THE 4TH - 23. AT LAVATORIES IN TOILET AND BATHING FACILITIES, KNEE CLEARANCE SHALL BE PROVIDED THAT IS 30 COMPLY WITH 11B-404 DOORS, DOORWAYS, AND GATES. §11B-206.4.5 §1 INCHES HIGH. THE CENTERLINE OF THE ISA SHALL BE A MAXIMUM OF 6 INCHES FROM THE CENTERLINE OF THE SIDE WALL AND 56 INCHES MINIMUM MEASURED PERPENDICULAR FROM THE REAR WALL. A MINIMUM 60 INCHES 5TH INCHES IN WIDTH FOR A DEPTH OF 11 INCHES AT 9 INCHES ABOVE THE FINISH FLOOR OR GROUND AND FOR 1 B-404.3.7 PARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE AND ITS LOWER CORNER AT, OR WIDE AND 48 INCHES DEEP MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET. A DEPTH OF 8 INCHES AT 27 INCHES ABOVE THE FINISH FLOOR OR GROUND INCREASING TO 29 INCHES HIGH TECHNICAL REQUIREMENTS FOR ACCESSIBLE ROUTES RAMPS LOWER SIDE ALIGNED WITH, THE END OF THE PARKING SPACE LENGTH. §11B-502.6.4.1 §11B-604.3.1 6TH MINIMUM ABOVE THE FINISH FLOOR OR GROUND AT THE FRONT EDGE OF A COUNTER WITH A BUILT-IN B. THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE AND SHALL BE MARKED WITH AN INTERNATIONAL LAVATORY OR AT THE FRONT EDGE OF A WALL-MOUNTED LAVATORY FIXTURE. §11 B-306.3.3, FIGURE 13. ACCESSIBLE ROUTES SHALL CONSIST OF ONE OR MORE OF THE FOLLOWING COMPONENTS: WALKING 45. PROVIDE RAMP DETAILS, INCLUDING SLOPE, LANDINGS, AND HANDRAILS. SYMBOL OF ACCESSIBILITY (ISA) COMPLYING WITH SECTION 11 B-703.7.2.1 ISA A MINIMUM 36 INCHES WIDE BY 13. THE SEAT HEIGHT OF A WATER CLOSET ABOVE THE FINISH FLOOR SHALL BE 17 INCHES MINIMUM AND 19 11 B-306.3(C) SURFACES WITH A RUNNING SLOPE NOT STEEPER THAN 1:20 (5%), DOORWAYS, RAMPS, CURB RAMPS EXCLUDING 36 INCHES HIGH IN WHITE OR A SUITABLE CONTRASTING COLOR. THE CENTERLINE OF THE ISA SHALL BE A INCHES MAXIMUM MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUNG THE RETURN TO A THE FLARED SIDES, ELEVATORS, AND PLATFORM LIFTS. §1113-402.2 46. RAMP RUNS SHALL HAVE A RUNNING SLOPE NOT STEEPER THAN 1:12 (8.33%). §116-405.2 MAXIMUM OF 6 INCHES FROM THE CENTERLINE OF THE PARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH LIFTED POSITION. SEATS SHALL BE 2 INCHES HIGH MAXIMUM AND A 3 INCH HIGH SEAT SHALL BE PERMITTED JOB NUMBER 24. AT DINING AND WORK SURFACES REQUIRED TO BE ACCESSIBLE, KNEE CLEARANCE SHALL BE PROVIDED THAT OF THE PARKING SPACE AND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE PARKING ONLY IN ALTERATIONS WHERE THE EXISTING FIXTURE IS LESS THAN 15 INCHES HIGH. §11B-604.4 (SEE IS 30 INCHES IN WIDTH AT 27 INCHES ABOVE THE FINISH FLOOR OR GROUND FOR A DEPTH OF AT LEAST 19 14. THE RUNNING SLOPE OF WALKING SURFACES SHALL NOT BE STEEPER THAN 1:20 (5%). THE CROSS SLOPE 47. CROSS SLOPE OF RAMP RUNS SHALL NOT BE STEEPER THAN 1:48 (2.083%). §11B-405.3 SPACE. §11B-502.6.4.2 EXCEPTION FOR RESIDENTIAL UNITS) INCHES. §116-306.3 OF WALKING SURFACES SHALL NOT BE STEEPER THAN 1:48 (2.083%). §11B-403.3 ARCH PROJECT#: 18-287 48. FLOOR OR GROUND SURFACES OF RAMP RUNS SHALL COMPLY WITH 1113-302 FLOOR OR GROUND 24. AN ADDITIONAL SIGN SHALL BE POSTED EITHER; 1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN 14. GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSEST TO THE WATER CLOSET AND ON THE REAR 25. FOR ELEMENTS REQUIRED TO PROVIDE KNEE CLEARANCE EXCEPT LAVATORIES IN TOILET AND BATHING 15. EXCEPT AT TURNS OR PASSING SPACES, THE CLEAR WIDTH OF WALKING SURFACES SHALL BE 36 INCHES SURFACES. CHANGES IN LEVEL OTHER THAN THE RUNNING SLOPE AND CROSS SLOPE ARE NOT PERMITTED ON OFF-STREET PARKING FACILITY OR 2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING AND VISIBLE WALL. WHERE SEPARATE GRAB BARS ARE REQUIRED ON ADJACENT WALLS AT A COMMON MOUNTING HEIGHT, AN FACILITIES AND DINING AND WORK SURFACES, KNEE CLEARANCE SHALL BE PROVIDED THAT IS 30 INCHES IN MINIMUM. §11B-403.5.1 RAMP RUNS. §11B-405.4 FROM EACH PARKING SPACE. §11B-502.8 L-SHAPED GRAB BAR MEETING THE DIMENSIONAL REQUIREMENTS OF SECTIONS 1113-604.5.1 SIDE WALL AND WIDTH FOR A DEPTH OF 11 INCHES AT 9 INCHES ABOVE THE FINISH FLOOR OR GROUND AND FOR A DEPTH OF 1113-604.5.2 REAR WALL SHALL BE PERMITTED. §11B-604.5 8 INCHES AT 27 INCHES ABOVE THE FINISH FLOOR OR GROUND. §11B-306.3, FIGURE 11B-306.3(A) 16. THE CLEAR WIDTH SHALL BE PERMITTED TO BE REDUCED TO 32 INCHES MINIMUM FOR A LENGTH OF 24 49. THE CLEAR WIDTH OF A RAMP RUN SHALL BE 48 INCHES MINIMUM. §11B-405.5 A. THE ADDITIONAL SIGN SHALL NOT BE LESS THAN 17 INCHES WIDE BY 22 INCHES HIGH. §11B-502.8.1 DRAWN BY CHECKED BY INCHES MAXIMUM PROVIDED THAT REDUCED WIDTH SEGMENTS ARE SEPARATED BY SEGMENTS THAT ARE 48 15. THE SIDE WALL GRAB BARS SHALL BE 42 INCHES LONG MINIMUM, LOCATED 12 INCHES MAXIMUM FROM THE 26. EXCEPT FOR DINING AND WORK SURFACES, KNEE CLEARANCE MAY REDUCE AT A RATE OF 1 INCH IN DEPTH INCHES LONG MINIMUM AND 36 INCHES WIDE MINIMUM. §11B-403.5.1 EXCEPTION 1 50. THE RISE FOR ANY RAMP RUN SHALL BE 30 INCHES MAXIMUM. §11B-405.6 B. THE ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERS WITH A MINIMUM HEIGHT OF 1 INCH THE FOLLOWING: REAR WALL AND EXTENDING 54 INCHES MINIMUM FROM THE REAR WALL WITH THE FRONT END POSITIONED 24 JR ADR FOR EACH 6 INCHES BETWEEN 9 INCHES AND 27 INCHES ABOVE THE FINISH FLOOR OR GROUND. §11 B-502.8.2 INCHES MINIMUM IN FRONT OF THE WATER CLOSET. §11 B-604.5.1 §11 B-306.3.4, FIGURE 11 B-306.3 17. THE CLEAR WIDTH FOR WALKING SURFACES IN CORRIDORS SERVING AN OCCUPANT LOAD OF 10 OR MORE 51. RAMPS SHALL HAVE LANDINGS AT THE TOP AND THE BOTTOM OF EACH RAMP RUN. §11B-405.7 SHALL BE 44 INCHES MINIMUM. §11B-403.5.1 EXCEPTION 2 "UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOT DISPLAYING DISTINGUISHING 16. THE REAR GRAB BAR SHALL BE 36 INCHES LONG MINIMUM AND EXTEND FROM THE CENTERLINE OF THE SHEET CONTENT 27. KNEE CLEARANCE SHALL EXTEND 25 INCHES MAXIMUM UNDER AN ELEMENT AT 9 INCHES ABOVE THE FINISH PLACARDS OR SPECIAL LICENSE PLATES ISSUED FOR PERSONS WITH DISABILITIES WILL BE TOWED AWAY AT THE WATER CLOSET 12 INCHES MINIMUM ON ONE SIDE AND 24 INCHES MINIMUM ON THE OTHER SIDE. FLOOR OR GROUND. §11 B-306.3.2 52. LANDINGS SHALL COMPLY WITH 11 B-302 FLOOR OR GROUND SURFACES. CHANGES IN LEVEL ARE NOT §11 B-604.5.2 (SEE EXCEPTIONS) PROTRUDING OBJECTS 18. THE CLEAR WIDTH FOR SIDEWALKS AND WALKS SHALL BE 48 INCHES MINIMUM. §11B-403.5.1 EXCEPTION 3 PERMITTED. §11B-405.7.1 OWNER'S EXPENSE. TOWED VEHICLES MAY BE RECLAIMED AT: _________________________ OR BY ACCESSIBILITY NOTES TELEPHONING __________. 17. FLUSH CONTROLS SHALL BE HAND OPERATED OR AUTOMATIC. HAND OPERATED FLUSH CONTROLS SHALL 28. EXCEPT FOR HANDRAILS, OBJECTS WITH LEADING EDGES MORE THAN 27 INCHES AND LESS THAN 80 INCHES 19. THE CLEAR WIDTH FOR AISLES SHALL BE 36 INCHES MINIMUM IF SERVING ELEMENTS ON ONLY ONE SIDE, 53. THE LANDING CLEAR WIDTH SHALL BE AT LEAST AS WIDE AS THE WIDEST RAMP RUN LEADING TO THE BLANK SPACES SHALL BE FILLED IN WITH APPROPRIATE INFORMATION AS A PERMANENT PART OF THE SIGN. COMPLY WITH SECTION 1113-309.4 OPERATION EXCEPT THEY SHALL BE LOCATED 44 INCHES MAXIMUM ABOVE ABOVE THE FINISH FLOOR OR GROUND SHALL PROTRUDE NO MORE THAN 4 INCHES HORIZONTALLY INTO THE 20. WHERE THE ACCESSIBLE ROUTE MAKES A 180 DEGREE TURN AROUND AN ELEMENT WHICH IS LESS THAN 48 LANDING. §11B-405.7.2 RELATIONSHIP TO ACCESSIBLE ROUTES THE FLOOR. FLUSH CONTROLS SHALL BE LOCATED ON THE OPEN SIDE OF THE WATER CLOSET EXCEPT IN CIRCULATION PATH. HANDRAILS MAY PROTRUDE 4�1Z INCHES MAXIMUM. §11B-307.2, FIGURE 11 B-307.2AMBULATORY ACCESSIBLE COMPARTMENTS COMPLYING WITH SECTION 11 B-604.8.2 AMBULATORY ACCESSIBLE SHEET NO INCHES WIDE, CLEAR WIDTH SHALL BE 42 INCHES MINIMUM APPROACHING THE TURN, 48 INCHES MINIMUM AT 25. PARKING SPACES AND ACCESS AISLES SHALL BE DESIGNED SO THAT PERSONS USING THEM ARE NOT 29. FREE-STANDING OBJECTS MOUNTED ON POSTS OR PYLONS SHALL OVERHANG CIRCULATION PATHS NO MORE THE TURN AND 42 INCHES MINIMUM LEAVING THE TURN. §11B-403.5.2 54. TOP LANDINGS SHALL BE 60 INCHES WIDE MINIMUM. §11B-405.7.2.1 REQUIRED TO TRAVEL BEHIND PARKING SPACES OTHER THAN TO PASS BEHIND THE PARKING SPACE IN WHICH COMPARTMENTS. §11B-604.6 THAN 12 INCHES WHEN LOCATED FROM 27 TO 80 INCHES ABOVE THE FINISH FLOOR OR GROUND. §11B-307.3, THEY PARKED. §11B-502.7.1 FIGURE 11B-307.3(A) 21. FOR PASSING SPACES, AN ACCESSIBLE ROUTE WITH A CLEAR WIDTH LESS THAN 60 INCHES SHALL PROVIDE 55. THE LANDING CLEAR LENGTH SHALL BE 60 INCHES LONG MINIMUM. §11B-405.7.3 18. TOILET PAPER DISPENSERS SHALL COMPLY WITH SECTION 1113-309.4 OPERATION AND SHALL BE 7 INCHES 30. PROTRUDING OBJECTS SHALL NOT REDUCE THE CLEAR WIDTH REQUIRED FOR ACCESSIBLE ROUTES. PASSING SPACES AT INTERVALS OF 200 FEET MAXIMUM. PASSING SPACES SHALL BE EITHER: A SPACE 60 26. A CURB OR WHEEL STOP SHALL BE PROVIDED IF REQUIRED TO PREVENT ENCROACHMENT OF VEHICLES MINIMUM AND 9 INCHES MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THE CENTERLINE OF THE §11 B-307.5 INCHES MINIMUM BY 60 INCHES MINIMUM; OR, AN INTERSECTION OF TWO WALKING SURFACES PROVIDING A 56. BOTTOM LANDINGS SHALL EXTEND 72 INCHES MINIMUM IN THE DIRECTION OF RAMP RUN. §11B-405.7.3.1 OVER THE REQUIRED CLEAR WIDTH OF ADJACENT ACCESSIBLE ROUTES. §11B-502.7.2 DISPENSER. THE OUTLET OF THE DISPENSER SHALL BE BELOW THE GRAB BAR, 19 INCHES MINIMUM ABOVE THE 31. LOWEST EDGE OF A SIGN OR OTHER OBSTRUCTION, WHEN MOUNTED BETWEEN POSTS OR PYLONS T-SHAPED SPACE COMPLYING WITH 11B-304.3.2 T-SHAPED SPACE WHERE THE BASE AND ARMS OF THE FINISH FLOOR AND SHALL NOT BE LOCATED BEHIND THE GRAB BARS. DISPENSERS SHALL NOT BE OF A TYPET� 1 SEPARATED WITH A CLEAR DISTANCE GREATER THAN 12 INCHES, SHALL BE LESS THAN 27 INCHES OR MORE T-SHAPED SPACE EXTEND 48 INCHES MINIMUM BEYOND THE INTERSECTION. §11B-403.5.3 57. RAMPS THAT CHANGE DIRECTION BETWEEN RUNS AT LANDINGS SHALL HAVE A CLEAR LANDING 60 INCHES THAT CONTROL DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS PAPER FLOW. §11B-604.7 03 THAN 80 INCHES ABOVE THE FINISH FLOOR OR GROUND. §11B-307.3, FIGURE 11B-307.3(B)