Laserfiche WebLink
LATH & PLASTER <br />Section 09200 <br />15-1207 <br />accepted equal. <br />Note: See specification section 09300 -Ceramic Tile for products and installation of <br />mortar bed at ceramic the walls where applicable. Contractor is responsible for the <br />coordination and installation of this work. <br />G. Strip Lath: Stripite, 4 -inch wide strips of Expanded Metal Lath, 3.4# galvanized diamond <br />mesh as manufactured by Clark Western or accepted equal. See Part 3 for installation <br />location and requirements <br />H. Tie wire: 18 ga. galvanized annealed low carbon steel wire for securing metal lath and lacing. <br />Use 16 gauge for all other applications. <br />Fasteners for Backing Paper: <br />1. Cap Nails: Nails with 1 inch diameter plastic cap, provided by manufacturer of Backing <br />Paper, first layer. <br />2. Cap Staples: Staples with 1 inch diameter plastic cap provided by manufacturer of <br />Backing Paper, first layer. <br />3. Wood Cap Screws: Wood screws with 2 inch diameter plastic cap, provided by <br />manufacturer of Backing Paper, first layer. <br />4. Wrap Cap Screws: Tyvek Wrap Cap Screws; self -tapping with 2 inch diameter plastic <br />cap, by DuPont, or accepted equal. <br />J. Lath Staples: 16 ga., 15/16" wide crown x 1'h" long galvanized staples. <br />K. Screws (for metal framing): Self -drilling wafer head screws, ASTM C1002, Type S. No. 8 by <br />length as required for at least 3/8 inch into steel framing, minimum 500 hour corrosion <br />resistant finish per ASTM B117. <br />L. Concrete/CMU Fasteners: Appropriate diameter x 5/8-3/4" length, washered head, drive pin <br />fasteners utilizing powder or gas activated fastening system. <br />M. Plaster Accessories: Conforming to ASTM C1063; fabricated from 26 gauge galvanized <br />steel, G60 coating unless otherwise noted (ASTM A924/A924M). All exposed accessories to <br />be pre -finished at job site per Section 09900, Painting, unless otherwise noted. <br />1. Interior Corner Reinforcement: Clark Dietrick Cornerite with 3 -inch wide flanges. <br />2. Expansion Screed: Stockton Products M -Screed, galvanized steel, 1/2" point to point or <br />accepted equal. <br />3. Exterior Corner Bead: Clark Dietrick #2A -Reinforced flange Corner bead for straight <br />installations and #1A -Expanded Corner Bead for curved installations or accepted equal. <br />4. Reveal Screed: Stockton Products Reveal Screed (SVR), galvanized steel, unvented, <br />1 inch point to point or as shown on drawings or accepted equal, prefinished with <br />powder coating, custom color. Field touch-up as required. <br />5. Ventilating Screed: Stockton Products Soffit Vent (SVR), galvanized steel, vented with <br />1/4" holes, 2-1/2 inches point to point or as shown on drawings, or accepted equal, <br />prefinished with powder coating, custom color. Field touch-up as required. <br />6. Casing Bead: Clark Dietrick #66 Short Flange Casing Bead, galvanized steel for <br />installation over framed walls or approved equal. Use the #66 Expanded Flange <br />Casing Bead for installations over concrete or CMU walls or accepted equal. Provide <br />weep holes where shown. <br />7. Perforated Drip Mould: Stockton Products Fascia/Soffit Mould (FSM), galvanized steel, <br />