|
Z OPERATION OF ®General safety requirements for equipment,machinery:
<br /> EQUIPMENT/MACHINERY • Arrange worksite for safe access to equipment/machinery.
<br /> M Point-of-operation hazards • Use equipment/machinery in accordance with manufacturer's use and safety instructions.
<br /> ®Pinch points,moving parts • Ensure point-of-operation,mechanical power transmission,other moving parts are guarded with protective
<br /> ®'Struck-by,''caught between' devices;do not override interlocks,guards,protective devices.
<br /> ®Hot surfaces,heat • Secure long hair/loose clothing/hanging jewelry near moving/rotating parts.
<br /> ®Extension cords,flexible wire • Heed warning signs/labels,keep safe distance;avoid locations of"struck by"and"caught between"hazards.
<br /> • Implement lockout/tagout for repairs/adjustments/tooling changes.
<br /> ® Fuel related(gas or liquid)
<br /> ® Hydraulic pressure I ® Use safe lifting practices for movement of heavy portable equipment
<br /> El Pneumatic pressure i
<br /> ®Implement safe work practices for compressed air,pressurized systems(pneumatic/hydraulic),stored energy.
<br /> El Kinetic,stored energy
<br /> El For climbing/fall hazards associated with large equipment,see Section BA.,"Fall Hazards."
<br /> ® Noise j ®For electrical hazards,see Section 6.8.,"Electrical Hazards."
<br /> El Emissions,discharge gases ®Operate fuel-powered equipment in well ventilated location.
<br /> El Working at heights,falls i
<br /> ®Use safe practices for fuels,see Section B.13.,"Commercial Chemical Products."
<br /> ®Lifting,repetitive motion
<br /> i
<br /> I i Geosyntec Procedure(s):HS-109-Hearing Conservation,HS-113-Personal Protective Equipment,
<br /> I
<br /> El Illumination HS-119-Lockout/Tagout,HS-121-Electrical Safety,HS-503-Powered Hand Tools,Others as applicable
<br /> © Electrical
<br /> ❑ LOCKOUT/TAGOUT OF HAZARDOUS ❑Implement control-of-hazardous-energy practices(lockout/tagout),provide lockout/tagout locks and
<br /> ENERGY devices,training workers,designate"authorized"personnel,notify"affected"personnel.
<br /> i
<br /> j Geosyntec Procedure(s):HS-119-Lockout Tagout
<br /> WELDING,CUTTING,HOT WORK ❑General safe work practices:
<br /> (GAS OR ARC) j • Hot work permit system to be implemented.
<br /> UV/IR light-eye/skin burns,hot-work • Operator properly protected(eye protection,clothing,apron,etc.).
<br /> hazards,toxic welding fumes, • Fire hazard controls(watcher,fire extinguisher,water,isolate combustibles).
<br /> compressed gases,electrical shock • Protect nearby i y personnel from hazardous UV,IR light(shielding,curtain).
<br /> ❑For gas welding/cutting,use gas cylinder safe practices(secured,upright,caps on when not in use,prevent
<br /> Damage;never secure gas cylinders to metal bench used for arc welding).
<br /> ❑ For arc welding,follow electrical safe work practices.See Section B.8.,"Electrical Hazards."
<br /> ❑See Section B.13.,"Commercial Chemical Products,"for hazards of welding rods(toxic metals),welding gases.
<br /> Geosyntec Procedure(s):HS-511-Welding,Cutting and Other Hot Work
<br /> ❑ j COMPRESSED AIR,COMPRESSOR ❑Never direct nozzle toward body;do not use compressed air for cleaning clothes.
<br /> i
<br /> (for compressed gases,see ❑If compressed air is used for cleaning,restrict pressure to 30 psi or below,equip nozzle with chip guard.
<br /> Section B.13.,"Compressed Gases") ❑Use eye protection.
<br /> i ❑ Ensure air tank,hoses,fittings are in good repair using factory fittings.
<br /> PORTABLE GENERATOR ® Follow general safety practices for Operation of Equipment/Machinery(above),and as follows:
<br /> Hazards:Electrical shock,carbon • Use in accordance with manufacturer's instructions.
<br /> monoxide in exhaust,fuel-related j • Keep generator and work area dry.
<br /> fire,injury from mechanical hazards, i • Never use indoors,or near building air intake vents due to carbon monoxide hazard.
<br /> lifting j • Provide for ventilation and/or air monitoring where hazardous accumulation of exhaust emissions is possible.
<br /> j • Use hearing protection in close proximity to operating generator,as needed.
<br /> • Use power cords/extension cords specified by instructions.
<br /> • Use ground-fault circuit interrupters(GFCls)in accordance with manufacturer's instructions.
<br /> i
<br /> • See Section B.8.,"Electrical Hazards."
<br /> • Shut down equipment before refueling. See safe practices for flammable/combustible liquids in Section B.13.,
<br /> "Commercial Chemical Products."
<br /> Geosyntec Procedures:HS-109-Hearing Conservation,HS-111-Air Monitoring,
<br /> HS-115-Hazard Communication(for fuel),HS-121-Electrical Safety,Others as applicable
<br /> PORTABLE HEATERS ❑Follow general safety practices for Operation of Equipment/Machinery(above),and as follows:
<br /> (electric or fuel powered) • Keep heater dry,and locate heater on level surface away from high traffic areas.
<br /> Hazards: • Never use fuel-powered heaters indoors,or near air intake vents,due to carbon monoxide hazard.
<br /> Electric-powered: Electrical shock, • Provide for ventilation and/or air monitoring where hazardous accumulation of exhaust emissions is possible.
<br /> fires from hot surfaces. i • Keep combustible materials at least 3 feet from hot surfaces.
<br /> Fuel powered:Carbon monoxide in • Do not use an extension cord or power strip to power an electric heater.
<br /> iexhaust,fires from hot surfaces, • For electric heaters,See Section B.8.,"Electrical Hazards."
<br /> fuel-related fires • Shut down fuel-powered equipment before refueling. See safe practices for flammable/combustible liquids
<br /> ! and/or compressed gases in Section B.13.,"Commercial Chemical Products."
<br /> Geosyntec Procedures: HS-111-Air Monitoring,HS-115-Hazard Communication(for fuel,
<br /> HS-121-Electrical Safety,Others as applicable
<br /> 13.6. DRILLING ® Applicable ❑ Not Applicable,Not Anticipated
<br /> EXPLANATORY NOTES,CLARIFICATIONS:
<br /> A drill rig will be operated by Gregg Drilling&Testing personnel to advance hollow stem augers to approx.25 ft bgs,with subsequent monitoring well installation.
<br /> Geosyntec° THA—Drilling/Development Operations Safety 1/29/2019
<br /> GSH Stockton Phyto,TR0712C Page 7
<br /> consultants
<br />
|