Laserfiche WebLink
5} Oipock number(XI=82' top of The Face Seal Adaptor in the spill container to the <br /> Tank dlarneter M=9r bunum of tie tank IDim,OBI. <br /> M-( _M 9 ' '= 1(r) IlMRWANT;Impect the riser pipe for any ioreugn nmte-- <br /> (7) _ IT rial, Over spray from tank relininq or any intemal burrs <br /> 6) ( -2'—C (i ioff-2'F81 ins#de of pipe must be removed prior to instaW tion_ <br /> C=8" Failure to have an unobstructed riser p(pe may prevent <br /> 7) Is 8'less than 6r112'7 pfaper Installation and cperation of the valve. The <br /> 7150 i5 designed for Installation Into schedule 40 riser <br /> N O Warsure thr d istance from the top of the ESA- pipes, The 71 SO cannot be Irrs#iailed into schedule 80 <br /> 440 Fare Seal 7►daptm installed on the riser pipe d ser plpews, <br /> to the inside,top lip of the storage tank and ob- STEP 2: AfA K THE TUBE <br /> twin measurement(A). Used*result frorn Step 1 and HIM LOCATE THE <br /> POSPl7W OF THE 7 TSO AT 95%TANK CAPA07Y to <br /> !J pper tine length =C+ # mark the upper tube. measure the distance from the <br /> seam where the upper tube and val►re body meet. Use <br /> Far to le models only,endMg in"T": Up rTu e a tape measure to mark the calculated Upper Labe <br /> Length r C + (A)- 1-117" Length onto the upper-tube. See Figure 2 <br /> ASSEV LV INSTRUCTION-S Tape nwwsum <br /> IMPORTANT. Each of the nu rnbered steps in the in- <br /> stallation instructions are designed as a CHECK LIST to <br /> ensure proper Installation and trouble fee operation of <br /> the OPW 7150 I7r+erfill Prevention Valve. <br /> Read and follow these steps carefuIlyr checking them Rlrr PV& <br /> off as you prpceed. wit)Feat (A) <br /> 6erl1*d4 Dior To Ta nk <br /> Fi9vre rr4jm rs coi'reWnd ZO step nurmroers for easy <br /> Tap I.t .) To �" <br /> nefemnce. <br /> STEP 7: MEASURE <br /> Install the 0F1W Face Seal Adaptor and the OPW Thread- <br /> on 5.pi11 Container an the Fill Riser(Refer to tiFwe Lnjm0a- <br /> Bart Instructions Supplied wkth the SgH Container). in- Figure 7 <br /> sen a tapL►measure through the riser pipe and hook It <br /> under the lnside of tank in the lengthwise dk*ction. - <br /> Measum the distarKe f=orn the top of the Face Seat <br /> Adapter thread s I nsidrs the base crf the spill coma I nor <br /> bucket jug below the drain valve oud at window to the 4•t,W <br /> inside,top lip of the storage tank(Dim, W)(Ut Figritr NOF& <br /> 1 WA1. <br /> The top flange on the 7150 w111 rest on the Face Seal <br /> AdapWr just below the drain valve outlet,and be <br /> lacked in place between the e Face al Adapter and the ° <br /> 4' nipple that iS installed in the Spill container with the <br /> Jack Screw Kit 15m Fig, IAA. jfnr riser pipe configura- iaak Saew <br /> tions otlw than that shown,consult insta;ladon drarw- MMELIM � tClt <br /> ings or use other necessary means to measure Dimt:n• .�tWWrb 04tkig saw <br /> skon W). {Top cc Fam <br /> Fam Smi <br /> Usjnya tape measu re.nvmmure the dlstancetrornthe ?ISO Aftpkar <br /> u1s 7A S <br />