SU-2601296_SSNL - Laserfiche WebLink

Home Browse Search

PLUMBING GENERAL NOTES: -&� ^) z 1 . ALL PLUMBING WORK SHALL CONFORM TO THE 2025 CALIFORNIA PLUMBING CODE (CPC) AND LOCAL REQUIREMENTS. 2. CLEANOUTS SHALL BE SAME SIZE AS PIPE AND ACCESSIBLE FROM THE PLAN. INSTALL COVER FLUSH WITH FLOOR OR WALL. 3. SLEEVES SHALL BE PROVIDED TO PROTECT ALL PIPING THROUGH CONCRETE, MASONRY, AND FLOORS. 4. ALL PIPING SHALL BE INSTALLED TO MAINTAIN CLEARANCES FROM STRUCTURAL MEMBERS AND BE SECURED USING APPROVED CLAMPS OR INSULATORS. 5. BUILDING SEWER SHALL MAINTAIN MINIMUM 1/4" PER FOOT SLOPE FOR 2-1/2" AND SMALLER, AND 1/8" PER FOOT FOR 3" AND LARGER ADU WATER SERVICE TO BE UNLESS NOTED OTHERWISE. SUPPLIED FROM EXISTING CASAVISION LLC ON-SITE SHARED WELL SYSTEM. 6. PIPE SIZES SHOWN ARE DIAGRAMMATIC AND BASED ON TYPICAL CONDITIONS. CONTRACTOR TO VERIFY FINAL PIPE SIZING AND IF STATIC PRESSURE OR FLOW IS INSUFFICIENT, EXISTING WELL PUMP: 1 1/2 HP, ROUTING IN FIELD PER CPC AND INSPECTOR APPROVAL. PROVIDE ADDITIONAL STORAGE TANK AND 20 GPM CAPACITY. PRESSURE 6507 PACIFIC AVE, #281 BOOSTER PUMP SYSTEM AS REQUIRED TO �03/4" C SWITCH CURRENTLY SET AT STOCKTON, CA 95207 MAINTAIN MINIMUM 40 PSI AT FIXTURES. W APPROXIMATELY 60 PSI. LEGEND: CONTRACTOR/OWNER SHALL VERIFY WELL 3 H — HOT WATER F. 209-696-8551 CAPACITY, RECOVERY RATE, AND SYSTEM CASAVISIONDESIGN@GMAIL.COM PERFORMANCE PRIOR TO FINAL INSTALLATION. C = COLD WATER 3040 SL S = SEWER LINE 100 AMP 3 G = GAS LINE WH = WATER HEATER -� 30-GALLON GAS WATER HEATER LOCATED IN ATTIC. PROVIDE PLUMBING VENTING: DRAIN PAN WITH APPROVED DISCHARGE TO EXTERIOR. a PROVIDE SERVICE PLATFORM AND MINIMUM 30"WORKING 1 . PLUMBING VENTS SHALL BE INSTALLED IN ACCORDANCE WITH THE CALIFORNIA PLUMBING CODE (CPC). HORIZONTAL VENTING CLEARANCE PER CPC. WATER HEATER TO BE ADEQUATELY SHALL BE PERMITTED ONLY ABOVE THE FLOOD-LEVEL RIM OF THE HIGHEST FIXTURE SERVED. EXISTING VENT LOCATIONS, SIZES, SUPPORTED AND FRAMED BETWEEN TRUSSES; DO NOT CUT AND ROUTING SHALL BE VERIFIED IN FIELD. CONTRACTOR SHALL PROVIDE ADDITIONAL VENTING OR RE-VENTING AS REQUIRED TO 0 W OR MODIFY TRUSS MEMBERS. PROVIDE VENTING AND H 3 COMBUSTION AIR PER CPC. MAINTAIN CODE-COMPLIANT TRAP PROTECTION. 03/4" G 2. BATHROOM EXHAUST FAN SHALL BE DUCTED DIRECTLY TO EXTERIOR IN ACCORDANCE WITH CBC/CMC AND MANUFACTURER r�►s S GAS CAS —CAS r►s—CaS r►s—CaS Ci CAS GAS REQUIREMENTS. EXHAUST AIR SHALL NOT TERMINATE IN ATTIC OR CONNECT TO PLUMBING VENT SYSTEMS. Q 1/2" G 7 01/2" G w W A ER WATER WATERWATER WATER WATER WATER ATER WATE" �3/ ATER WATER 3 w I o1/2" C WATER HEATER & FIXTURE NOTES: F- 1- _s S_ ss ss Hw O3/4"H,Q mw Hw w 1 . WATER HEATERS SHALL BE STRAPPED WITH METAL STRAPS AT THE TOP AND BOTTOM PER CPC. 1 01/2" H 2. WATER HEATERS INSTALLED IN ATTICS OR ABOVE FLOOR LEVEL SHALL HAVE A 1-1/2" DEEP PAN WITH A 3/4" DRAIN LINE TO THE m � A 7 I EXTERIOR. O 3. T&P RELIEF VALVE SHALL DISCHARGE BY GRAVITY TO APPROVED EXTERIOR TERMINATION PER CPC. D F A 4. WATER HEATERS SHALL HAVE PRESSURE AND TEMPERATURE RELIEF VALVES PER CPC AND BE ACCESSIBLE FOR SERVICE. 03/ " ®® ® ®® i 02" S A w � Hw Hw Hw Hw Hw s 5. A CONDENSATE DRAIN SHALL BE PROVIDED IF UNIT IS CONDENSING TYPE. O1/2" G £ I 6. HOT WATER PIPING AND FIRST 5 FEET OF COLD WATER PIPING SHALL BE INSULATED PER TITLE 24 (MIN. R-4 = 1"). GAS BAS c/2—c Gas 3 3 PROVIDE CLEAN OUT WA E WATER WAT �� TYP. TUBULAR SKYLIGHT 7. TUBS AND SHOWERS SHALL BE FITTED WITH INDIVIDUAL CONTROL VALVES FOR TEMPERATURE BALANCE (THERMOSTATIC OR Q� A 01/2" c ATER PRESSURE BALANCE). O 1/2'm=H 01/2" H >/2 'WATETER - 02 s — — — — — — — — N�2„ s GAS GENERAL NOTES: v O 1/2" `'� 1 . ALL GAS WORK SHALL COMPLY WITH THE 2025 CALIFORNIA PLUMBING CODE (CPC) AND APPLICABLE LOCAL REQUIREMENTS. � S2„ H ss _w ss ss ss ss ss ss s ss ss 2. GAS PIPING SHALL BE SIZED BASED ON TOTAL CONNECTED BTU LOAD AND LONGEST DEVELOPED LENGTH PER CPC TABLES; PROVIDE CLEAN OUT 0,/ 04„s H CONTRACTOR TO VERIFY FINAL APPLIANCE RATINGS IN FIELD PRIOR TO INSTALLATION. 3. CONTRACTOR/OWNER SHALL VERIFY EXISTING GAS SERVICE CAPACITY IS ADEQUATE FOR PROPOSED LOAD; COORDINATE WITH E� A UTILITY PROVIDER IF UPGRADE IS REQUIRED. �O3" s 4. PROVIDE ACCESSIBLE SHUTOFF VALVE AT EACH GAS APPLIANCE AND INSTALL FLEXIBLE CONNECTORS PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. A 5. ALL GAS PIPING SHALL BE PRESSURE TESTED AND INSPECTED PRIOR TO CONCEALMENT. LRW T 6. PROVIDE SEDIMENT TRAP (DRIP LEG) AT EACH GAS-FIRED APPLIANCE PER CPC. 01/2" C JF a 003/4" G �� z WATER SUPPLY SYSTEM: 1 . PROVIDE STORAGE AND BOOSTER SYSTEM AS REQUIRED BASED ON WELL CAPACITY AND PRESSURE TESTING. 2. TANK SHALL BE SUPPLIED BY EXISTING SHARED WELL. LL.I 3. PROVIDE A 1 HP BOOSTER PUMP SYSTEM WITH 40-GALLON DIAPHRAGM PRESSURE TANK, SIZED TO MAINTAIN 50-70 PSI AT THE Q I RESIDENCE UNDER NORMAL OPERATING CONDITIONS. Z 4. INCLUDE THE FOLLOWING: Q 4.1. FLOAT VALVE CONTROL WITHIN BUFFER TANK FOR AUTOMATIC FILL CONTROL W z ® 4.2. PROPER BACKFLOW PREVENTION DEVICE PER LOCAL JURISDICTION REQUIREMENTS w Z Q 4.3. ISOLATION VALVES AND UNIONS FOR SERVICEABILITY z ~ N 4.4. PRESSURE GAUGE ON DISCHARGE SIDE OF BOOSTER SYSTEM 3 U uj 4.5. GENERAL CONTRACTOR SHALL VERIFY: 0 O 4.6. EXISTING WELL PUMP CAPACITY (GPM) = a to 4.7. ADEQUACY OF WELL RECOVERY RATE N C)4.8. SHARED WELL CAPACITY TO SUPPORT ALL CONNECTED RESIDENCES 4.9. SYSTEM SHALL BE INSTALLED PER MANUFACTURER SPECIFICATIONS AND ALL APPLICABLE LOCAL PLUMBING AND HEALTH 06 ® DEPARTMENT REGULATIONS. Z a LLI J J Q ACRYLIC DOMF SELF-TAPPING ALUMINUM DATE: NOTE: SCREW — FLASHING N a - SHEET METAL H 12' SCREW - ROOFING N l 3l4"PLYWOOD l IF SHEATHING to STAINLESS STEEL SCREW '"' -6 LIGHT PIPE a FOIL TAPE a u DATE: G FLAT HEAD SCREW STAINLESS 4/25/ZO26 O PROPOSED 250-GALLON ABOVE-GROUND ,WITH SPEED NUT STEEL SCREW GAS PROPANE TANK. INSTALL PER FIRE CODE AND SCALE: AS NOTED PROPANE SUPPLIER REQUIREMENTS; VERIFY CLEARANCES AND ACCESS. DRAWN BY: TRIM RING SHEETROCK MG ! CEILING DIFFUSER TITLE: PLUMBING PLAN ROOF MOUNf' SHEET: PLUMBING PLAN TUBULAR SKYLIGHT DETAIL Pi 00 1/4"=1'-0" 1 N TS