PW-ENCDRWY-2403198 - Laserfiche WebLink

Home Browse Search

ALL WORK SHALL COMPLY WITH ALL STATE AND LOCAL CODES AND ANY OTHER REGULATING AUTHORITIES WHICH HAVE AUTHORITY OVER ANY PORTION OF THE WORK. PRIOR TO COMMENCEMENT OF ANY WORK, THE CONTRACTOR SHALL VERIFY EXISTING CONDITIONS AND NOTIFY THE DESIGN PROFESSIONAL IN RESPONSIBLE CHARGE FROM TESLA OF ANY DISCREPANCIES. ANY WORK PERFORMED IN CONFLICT WITH THE CONTRACT DOCUMENTS SHALL BE CORRECTED AT THE SUBCONTRACTORS SOLE EXPENSE. SUBCONTRACTOR INITIATED CHANGES SHALL BE SUBMITTED IN WRITING TO TESLA FOR APPROVAL BEFORE MAKING ANY CHANGES. DEVIATION FROM PLANS BEFORE WRITTEN APPROVAL FROM TESLA PLACES LIABILITY ON THE SUBCONTRACTOR. ALL EQUIPMENT SHALL BE MOUNTED AS SHOWN. WHERE DETAILS ARE NOT PROVIDED, CONTRACTOR SHALL USE STANDARD CONSTRUCTION PRACTICES. ALL SURFACES SHALL BE PATCHED AND PAINTED AROUND NEW DEVICES AND EQUIPMENT TO MATCH EXISTING FINISHES. ANY METAL SHAVINGS FROM SITE WORK SHALL BE CLEANED FROM ALL SURFACES WHERE OXIDIZED OR CONDUCTIVE METAL SHAVINGS MY CAUSE RUST, ELECTRICAL SHORT CIRCUITS, OR OTHER DAMAGE. APPROVALS FROM BUILDING INSPECTORS SHALL NOT CONSTITUTE AUTHORITY TO DEVIATE FROM THE DRAWINGS. NEW PAVEMENT INSTALLED AS PART OF THIS PROJECT SHALL MATCH EXISTING PAVEMENT SECTION. ASPHALT AND GAB DEPTHS SHALL BE MAINTAINED. GENERAL NOTES SUPERCHARGER NOTES 1.NEUTRAL MUST BE INCLUDED FOR PROPER OPERATION OF TESLA SUPERCHARGERS. 2.ALL CONDUIT FURNISHED AND INSTALLED BY CONTRACTOR. ALL WIRING FURNISHED BY TESLA AND INSTALLED BY CONTRACTOR. 3.ALL BUSHINGS AND WIRING INTERNAL OF PROPOSED SERVICE EQUIPMENT PROVIDED BY MANUFACTURER. ANY MODIFICATIONS SHALL REQUIRE ENGINEERING APPROVAL PRIOR TO ANY CHANGES BEING MADE. 4.ALL ALUMINUM(AI) CONDUCTORS TO RECEIVE ANTI-OXIDATION COATING DURING INSTALLATION. ALL OTHER CONDUCTORS ARE COPPER UNLESS OTHERWISE NOTED. 5.THE FOLLOWING CHARGING CABINETS AND THE CHARGING POSTS USED ON THIS PROJECT COMPLY WITH THE FOLLOWING STANDARDS: ·IEC 61851-23: 2014 / EN 61851-23: 2014 ·UL 2202: 2009(R2012) ·CAN CSA C22.2 NO. 107.1-01(R2011) 6.THE AFOREMENTIONED STANDARDS IDENTIFY THE REQUIREMENTS MET BY THE EQUIPMENT, INCLUDING BUT NOT LIMITED TO: ·PROTECTION AGAINST ELECTRIC SHOCK ·OVERLOAD AND SHORT CIRCUIT PROTECTION ·FAULT PROTECTION ·DEGREES OF PROTECTION AGAINST ACCESS TO HAZARDOUS LIVE PARTS ·THE INTERNAL COMPONENTS OF THE SYSTEM ARE PROPRIETARY. ANY QUESTIONS CONCERNING ACTUAL INTERNAL PROTECTIVE DEVICES MUST BE COORDINATED DIRECTLY WITH TESLA. 7.TESLA SUPERCHARGER SIGNAL WIRING RATED 1000V AND USED FOR POWER LIMITED CLASS 1 CIRCUITS SHALL BE PERMITTED TO RUN IN CONDUITS, CABLE TRAYS, WIRE WAYS, OR RACEWAYS ALONG WITH ASSOCIATED DC CONDUCTORS AS ALLOWED PER ART. 725.48(B)(1) AND 620.36. 8.SUPERCHARGER CABINET AC CONDUCTORS SIZED UNDER ENGINEERING SUPERVISION USING THERMAL MODELING SOFTWARE. SPECIFICATIONS ABOUT THE TRENCHING REQUIREMENTS ARE SHOWN IN E-501 9.FOR DC RUNS IN EXCESS OF 330 FEET, CONTACT TESLA. 10.UNDERGROUND CONDUITS SHALL BE SCHEDULE 40 PVC OR UL LISTED HDPE. THE ABOVEGROUND PORTION OF AN UNDERGROUND/ABOVEGROUND TRANSITION SHALL BE SCHEDULE 80 PVC OR UL LISTED HDPE. 11.ABOVEGROUND CONDUITS EXPOSED TO VEHICULAR OR EQUIVALENT PHYSICAL DAMAGE SHALL BE RMC. ABOVEGROUND CONDUITS NOT EXPOSED TO VEHICULAR OR EQUIVALENT DAMAGE SHALL BE PERMITTED TO BE EMT. 12.IF APPROVED BY TESLA CONSTRUCTION MANAGER, ALTERNATIVE CONDUIT MATERIALS SUCH AS FLEXIBLE OR FIBERGLASS ARE PERMISSIBLE IF INSTALLED PER MANUFACTURER INSTALLATION GUIDELINES AND LOCAL CODES. 13.WIRE SPLICES ARE NOT PERMITTED TO EXTEND WIRE RUN LENGTH. CONTRACTOR IS RESPONSIBLE FOR RERUNNING FULL LENGTH OF WIRE IF RUN LENGTH IS MISCALCULATED. 14.SPECIAL INSPECTION IS REQUIRED FOR ALL POST-INSTALLED CONCRETE ANCHORS. 15.PLANT GUARANTEE: CONTRACTOR SHALL GUARANTEE ALL PLANTS FOR A PERIOD OF ONE (1) YEAR FROM DATE OF PROJECT ACCEPTANCE BY THE OWNER. CONTRACTOR IS RESPONSIBLE FOR PLANT MAINTENANCE FOR THE FIRST GROWING SEASON. 16.IF EXISTING GRASS IS DAMAGED/REMOVED DURING CONSTRUCTION, CONTRACTOR SHALL APPLY SEED PER HYDROSEED METHOD. RATING OF SEED SHALL BE PER DISTRIBUTOR BASED ON SPECIES TYPE. 17.CONTRACTOR SHALL MATCH EXISTING LANDSCAPE; USE GRASS, RIVER ROCK, MULCH ETC. TO MATCH EXISTING LANDSCAPE AROUND EQUIPMENT, UNLESS OTHERWISE NOTED. 18.CONTRACTOR TO INSTALL WEED BARRIER IN FRONT OF SUPERCHARGER CABINETS AND SWITCHBOARD. BARRIER TO EXTEND FULL WIDTH AND DEPTH OF NEC REQUIRED WORKING CLEARANCES. GENERAL NOTES 1.ALL ELECTRICAL WORK SHALL COMPLY WITH THE CALIFORNIA ELECTRIC CODE AS AMENDED BY APPLICABLE STATE AND LOCAL CODES. 2.ALL WIRING SHALL BE MANAGED IN A PROFESSIONAL, WORKMAN-LIKE MANNER AND MUST BE SUPPORTED, SECURED, AND PROTECTED TO PREVENT DAMAGE. 3.AC CIRCUIT CONDUCTORS SHALL BE IDENTIFIED BY PHASE AND SYSTEM PER ART 210.5 OR 215.12. UNLESS OTHERWISE REQUIRED BY ART 210.5(1) OR AHJ, COLOR-CODING OF POWER CONDUCTORS SHALL BE AS FOLLOWS: CONDUCTOR 277/480V 120/208V PHASE A BROWN BLACK PHASE B ORANGE RED PHASE C YELLOW BLUE NEUTRAL GRAY WHITE 4.DC CIRCUIT CONDUCTORS SHALL BE IDENTIFIED PER ART 210.5 OR 215.12: CONDUCTOR STD COLOR ALT COLOR DC+RED RED-STRIPED DC-BLACK BLACK-STRIPED 5.TERMINATIONS OF AC, DC, AND COMMUNICATIONS CONDUCTORS SHALL BE PROFESSIONALLY AND LEGIBLY LABELED WITH CIRCUIT SCHEDULE IDENTIFIER, CONDUCTOR SIZE (AS APPLICABLE) AND TERMINATION TORQUE. 6.ALL EQUIPMENT SHALL BE LISTED BY A NRTL IN COMPLIANCE WITH ART 110.3. WHERE EXISTING NRTL LISTING CANNOT BE MAINTAINED, ENGINEERING APPROVAL SHALL BE OBTAINED PRIOR TO EQUIPMENT MODIFICATION, AND THE EQUIPMENT SHALL BE RELISTED BY A SUITABLE NRTL. 7.UNDERGROUND CONDUCTORS & CABLES TO BE INSTALLED IN CONDUIT UON. 8.ALL WIRES SHALL BE PROVIDED WITH STRAIN RELIEF AT ALL ENTRY INTO BOXES AS REQUIRED BY NRTL LISTING. 9.REFER TO MANUFACTURER'S CURRENT PLANNING AND INSTALLATION MANUAL FOR TORQUE SPECS FOR ALL BOLTS AND TERMINAL CONNECTIONS. 10.ALL CONDUCTOR TERMINATIONS ON BUSSING OR TRANSFORMER SPADES SHALL BE MADE WITH HIGH-PRESS CRIMP LUGS UON. 11.ALL TERMINATIONS OF ALUMINUM CONDUCTORS SHALL BE PROPERLY INSTALLED WITH BEST PRACTICES INCLUDING BUT NOT LIMITED TO: ·USE OF TERMINATION EQUIPMENT RATED FOR ALUMINUM AT THE CONDUCTOR TEMPERATURE, CURRENT, AND VOLTAGE ·ALLOWANCE FOR MOVEMENT DUE TO THERMAL EXPANSION/CONTRACTION ·PROPER COATING OF EXPOSED ALUMINUM WITH ANTI-OXIDIZATION COMPOUND ·USE OF CALIBRATED DEVICES TO TORQUE AND MARK TERMINALS TO REQUIRED SETTINGS 12.DUCT SEAL COMPOUND SHALL BE APPLIED WHEREVER CONDUITS TRANSITION INDOOR/OUTDOOR OR UNDERGROUND/ABOVEGROUND. REFER TO EQUIPMENT NOTES FOR ADDITIONAL DUCT SEAL REQUIREMENTS. 13.BELL ENDS SHALL BE INSTALLED WHEREVER CONDUIT ENTERS EQUIPMENT FROM UNDERGROUND AND WHEREVER POTENTIAL FOR DAMAGE TO CONDUCTORS IS PRESENT AT ANY POINT. BELL ENDS SHALL NOT PREVENT THE USE OF GROUNDING FITTINGS OR COUPLERS WHEN REQUIRED. 14.ALL STUB-UPS WITHIN FLOOR-MOUNTED EQUIPMENT SHALL BE 3-5" ABOVE FINISHED GRADE. 15.ALL CONDUITS EXPOSED TO VEHICULAR OR EQUIVALENT PHYSICAL DAMAGE SHALL BE RIGID GALVANIZED STEEL. 16.GROUND LUGS SHALL BE RATED FOR THEIR ENVIRONMENT AND CONDITION OF USE. ELECTRICAL NOTES SITE LEGEND (EXISTING OBJECTS) SCOPE OF WORK UTILITY PG&E - RULE 29 CATEGORY ITEMS TESLA TESLA CONTRACTOR UTILITY PRIMARY PRIMARY TRENCHING X INSTALL PRIMARY CONDUIT X INSTALL PULL ROPE X INSTALL PRIMARY FEEDERS X PROVIDE ROAD CUTS / ROAD BORES X PAVEMENT REPLACEMENT X TRANSFORMER PROVIDE TRANSFORMER PAD X INSTALL TRANSFORMER PAD X PROVIDE TRANSFORMER X INSTALL TRANSFORMER X INSTALL CONNECTIONS - PRIMARY X INSTALL CONNECTIONS - SECONDARY X PROVIDE BOLLARDS X INSTALL BOLLARDS X SWITCHBOARD PROVIDE METER X INSTALL METER X LAND SECONDARY FEEDERS X PROVIDE SWITCHBOARD PAD & PRE-CAST X INSTALL SWITCHBOARD PAD & PRE-CAST X SECONDARY SECONDARY TRENCHING X PROVIDE CONDUIT FROM SWITCHBOARD OUT 5' TO TRANSFORMER X INSTALL CONDUIT FROM SWITCHBOARD OUT 5' TO TRANSFORMER X INSTALL PULL ROPE X TERMINATE SECONDARY CONDUCTORS AT SWITCHBOARD X TERMINATE SECONDARY CONDUCTORS AT TRANSFORMER X PROVIDE SECONDARY CONDUCTORS X INSTALL SECONDARY CONDUCTORS X PROVIDE ROAD CUTS / ROAD BORES X PAVEMENT REPLACEMENT X 1.CAT5E/6 SHIELDED CABLE RUNS, WHICH INCLUDE INDIVIDUAL DAISY CHAINS OF INVERTERS FOR DIRECT MONITORING, HAVE A MAXIMUM TOTAL DISTANCE OF 328 FEET (100M) PER CHAIN. 2.RS485 CABLE RUNS, WHICH INCLUDE INDIVIDUAL DAISY CHAINS OF INVERTERS FOR DIRECT MONITORING, HAVE A MAXIMUM TOTAL DISTANCE OF 3280 FEET (1000M) PER CHAIN. 3.SWITCHES, METERS, POWERPACK CONTROLLERS, CT'S, AND PT'S, AND CONDUCTORS MARKED "PRE-INSTALLED" IN THE LINE DIAGRAM WILL ARRIVE TO SITE PRE-INSTALLED WITHIN THE SWITCHBOARD, AND WILL NOT REQUIRE ANY FIELD INSTALLATION OR MODIFICATION OF ANY KIND. COMMUNICATION NOTES 1.LOAD SIDE INTERCONNECTIONS SHALL COMPLY WITH CEC 705.12(B). 2.WHERE THE INTERCONNECTION POINT OCCURS ON FEEDERS, THE FEEDER AMPACITY SHALL NOT BE LESS THAN THE SUM OF ALL THE SOURCES CONNECTED TO THE FEEDER UNLESS THE FEEDER IS PROTECTED ON THE LOAD SIDE OF THE INTERCONNECTION POINT WITH OVERCURRENT PROTECTION NO GREATER THAN THE AMPACITY OF THE FEEDER. 3.TAP CONNECTIONS SHALL COMPLY WITH ART 240.21(B). 4.WHERE THE SUM OF ALL THE OVERCURRENT DEVICE RATINGS ON THE PANEL LOAD SIDE OF A MAIN OVERCURRENT PROTECTION DEVICE ARE LESS THAN THE RATING OF THE PANEL, PERMANENT WARNING LABELS WITH THE FOLLOWING WORDING MUST BE APPLIED: WARNING: THIS EQUIPMENT FED BY MULTIPLE SOURCES. TOTAL RATING OF ALL OVERCURRENT DEVICES EXCLUDING MAIN SUPPLY OVERCURRENT DEVICE SHALL NOT EXCEED THE AMPACITY OF THE BUSBAR. 5.WHERE THE SUM OF THE UTILITY OVERCURRENT DEVICE AND 125% OF INVERTER OUTPUT CIRCUIT CURRENT DOES NOT EXCEED 120% OF THE RATING OF THE BUSBAR, THE INTERCONNECTION POINT MUST BE ON THE OPPOSITE END OF THE BUSBAR FROM THE INCOMING UTILITY SOURCE AND A PERMANENT WARNING LABEL MUST BE APPLIED TO THE INTERCONNECTION POINT. 6.LOAD SIDE INTERCONNECTIONS SHALL BE MADE IN ACCORDANCE WITH THE EQUIPMENT MANUFACTURER'S INSTRUCTIONS AND SHALL NOT INVALIDATE THE NRTL LISTING OF THE EQUIPMENT. WHERE EXISTING NRTL LISTING CANNOT BE MAINTAINED, EQUIPMENT MUST BE RELISTED BY AN APPROVED NRTL SUITABLE FOR THE EQUIPMENT. UTILITY-INTERACTIVE INVERTER LOAD-SIDE INTERCONNECTION NOTES (FOR FUTURE PV SYSTEM AND BESS) SS RECTANGULAR STORM WATER INLET LIGHT POLE UTILITY POLE SIGN SANITARY SEWER MANHOLE WV WATER VALVE TREE ELE UNDERGROUND ELECTRIC LINE FENCE SS UNDERGROUND SANITARY SEWER LINE OHW OVERHEAD ELECTRIC LINE 1"12"0 PROPRIETARY AND CONFIDENTIAL ABCDEFGH 1 2 3 4 5 6 DATENO.REVISIONORIGINAL SIZE 24"X36" SHEET SIZE ARCH "D" 3500 DEER CREEK RD. PALO ALTO, CA 94304 (650) 681-5000 3/27/2024AARCH SITE PLAN COMMENTS10/18/2024BCIVIL AND BUILDING COMMENTS14700 THORNTON RDLODI, CA 95242, USNOTES G-002 REV: B IFP MVANDERWALPLOT DATE: 10/25/2024 9:20 a. m. JB-9528024TESLA SUPERCHARGER_LODI, CAPHASE 1: 16 SUPERCHARGERS