COMPLIANCE INFO 2012-2015 - Laserfiche WebLink

Home Browse Search

FRANKLIN FUELING �� M� ® �" �I L�•TITE STEP 16: FLARE COMPLETED STEP 19; INSTALLING LOWER DROP TUBE After the flaring procedure is completed, there should ASSEMBLY be smooth, flat 90-degree flare. Remove the flaring If a vise is used, clamp on the valve body casting only EBW 708 Auto Limiter II° Automatic Shut-off Valve and DropTube roller fthe fltool and the drive ring from the to avoid damage to the float. Mix the two-part J-B from are Kwik provided until the color is uniform. Using a drop tube. See Photo below. mixing stick, generously Measurement Work Sheet for Determining the Drop Tube Lengths g y apply J-B Kwik to the first - 6 male threads on the valve body as shown in s . Figure 2. Make sure coverage is completely around Date: the threads, and work the sealant down into the thread profile. Quickly thread the lower tube onto the valve -j body. Tighten the tube securely by hand or with a Site Location.(name) Installing Contractor:(name) _. strap wrench. Remove excess sealant and smooth ti r t sealant bead with water moistened mixing stick. Address Address i e Important: Allow sealant (J-B Kwlk) to cure for a G ky'. € minimum of 4 hours before installing the drop City/State City/State tube assembly into a tank with fuel. Contact/Phone Contact/Phone Tank Number: Product: Tank Type: Tank Manufacture: Tank Capacity, %/d' STEP 17: CHECK YOUR FLARE MEASUREMENT (from Mfg tank chart) Measure the upper drop tube for the correct length. Tank Diameter (from Mfg tank chart) ! 7.0 inches The Upper Drop tube mark should be at the base ofA the flare. See Photo Below. STEP 1 Determine the distance in inches the 708 Auto Limiter I1®Automatic Shut-off valve must et below the top of the tank for it to close when the tank reaches 95% or less capacity. be s w ,r , Using the manufactures tank chart,find the tank total capacity in gallons. Multiply this number by 95% (0.95). If you want the shut-off valve to close at less than 95% (i.e. 93% then use that percentage to g Fi urel2 multiply by the total tank capacity in gallons. Note: After the sealant(JB Kwik) has cured and Total tank capacity in gallons X (0.95 or less) = / gallons - 00 before installing the drop tube into the tank, a pressure test can be performed on the valve to check for vapor Using the manufacturer tank chart, convert the 95% or less capacity in gallons to inches = / ches tightness. Seal off both ends of the tube with �� il�i ' inflatable plumber's plugs. Apply a maximum 10 Use TABLE 1 to calculate the correct distance. inches W.C. (113 PSI) air pressure. If pressure does not hold and a leak can be located with soap solution, TABLE 1 do not install the valve. Send the valve back to Primary Tank Diameter in (inches) ( t FFSIPhil-Tite for warranty evaluation. Caution: Do not over-pressurize. Excess pressure Subtract the 95% Liquid level converted to inches ................. .--- ( f � �/ /� can damage the valve. STEP 18: INSTALLING,THE DROP TUBE SEAL This results is the distance in inches below the top of the tank .T .. Install the Phil-Tite Special Designed Drop Tube Seal . B - to the tank's 95% liquid level in inches ................................ -- ( (85039-DT) onto the drop tube with the flat side up against the drop tube flare. See Photo Below. Subtract 4" inches (from the last value obtained above) 4.00 g p This is "the distance" that the 708 Auto Limiter II® Shut-off valve l/ ry > o�ra�ar must be set below the top of the tank for the shut-off valve to ,f� ruaevnrHn�"; -t;AATS[Ri�ACE operate correctly when the tank reaches 95% or less capacity: j ) _ Transfer this number to Step 3 and Table 2 for determining the r UPPER DROP TUBE LENGTH. j0orrectly r 9 4