COMPLIANCE INFO 2012-2015 - Laserfiche WebLink

Home Browse Search

STEP 20: CUTTING LOWER END OF DROP STEP 24: CHECK INSTALLATION TUBE Insert the drop tube all the way into the tank until TOOLS NEEDED FOR INSTALLATION Install the MIF 4"X4" riser adapter using the Measuring from the underside of the inlet tube the flange and gasket seat onto the top of the AND ASSEMBLY: See Photo below. MIF 4X4 Installation Instructions onto the flange, mark the overall length of the drop tube a Phil-Tite MIF 4 X 4 Riser Adaptor. 1. 3/"X20' Ta top of the 4" inch tank riser and correctly ( ) distance of B minus 6" inches or as per local Ptdl-lite cast ion tour pe measure torque the adapter using the Phil-Tice codes or requirements. Determine dimension (B) Dustcarvit 003 seal 2. High-Tension Hacksaw, with fine tooth special tool adaptor (T-7102 Orange). from the DropTube Measurement Worksheet fin.gadep r,..,,a,:d (24-32 teeth/inch) blade or equivalent. taken in Step 3, Figure 1 (Top of the FFS MIF 4 X IMPORTANT3. Fine teeth half round file or de-burring 4 Riser Adaptor to the bottom of the tank). �� g any sharp Saw/Cut off the excess tube and fife off f ' ' tool Fit the Fill Spill Container Assembly _ __- �:` 4. Phil-Tite Flaring Tool Assy. (T-6100-FT) burrs. �.,,w.1, Install the fill spill container onto the MIF 5 Y4" Ratchet with 3" extension 4"X4" riser adaptor that is installed onto the Optional: Install the Phil-cite Tank Bottom ,14•Flat3czt ��___ •$•��°'�"�° Protector on the lower tube (Refer to Installation �— °"'' '' " s' 4" inch riser #o tank to Measure the >:.>. 6. 3116 X114 & 5116 X114 Hex with socket p ",<=y distance from the to of the spill container instructions supplied with the Tank Bottom E•`�°"•'" _Dra'ma&x adaptor p p� Protector). pp .4 thatsPa, 7. Small common screwdriver to finish grade (approximately 4 Y2" inches for 85000 series spill container and 1 %" Drop tube5eal ,_- —�Topflange ordroptube 8. Fine Tip Marking pen (Sharpie) or pencil STEP 21: PREPARE TANK RISER FOR inches for 85000-1 series spill container). � �- -- OVERFILL VALVE INSERTIONht1F04?JwAdapta e� ] This is to verify the 4si inch riser to the tank *� 4.11�readadtan,ksisahas been cut to the appropriate length. (See IMPORTANT: Inspect the tank riser pipe for any _ f- diagram below) foreign.material, Over spray from tank relining or any internal burrs inside of pipe must be removed Topc(staagetanf a. prior to installation. Failure to have an ' Q t. unobstructed tank riser pipe may prevent proper Umrdtoptube and akrtdmkerbedyfa<Aw O installation or operation of the valve. Thoroughly 4aembledandteftedtoCARBTP20),ID clean top of tank riser pipe. rswsr,t,tarYanre. .. - -. Important: Before installing the drop tube, allow the sealant to cure for minimum of 4 WeldedatrNhtbottom wbe �® hours. - o o Thfeadonboitornd{op Spill Collector Bottom drop tube should be STEP 22: REMOVE ELASTIC BAN© — — Dtstancetobe6'(orasper(ocalr � ents)— ang3e WARNING drop Tube Check the exposed floats for freedom of kem .,_ movement. If floats drag, inspect guide bar for Using electrically operated equipment near crop Tube — M/F 4x4 damage. Both of the floats should be free to move Figure 3 gasoline or gasoline vapors may result in Gasket Adaptor up and down without drag. STEP 25: FINAL INSTALLATION fire or explosion, causing personal injury Tank and property damage. Check to assure the --- Riser STEP 23: INSTALL THE DROP TUBE Install a Phil-Tite Fill Spill Container according to working area is free from such hazards, and _ Make sure the special drop tube seal (85039-DT) the manufacturer's installation instructions. always use proper precautions. is installed correctly. Slowly insert the drop tube Ensure that the drop tube does not rotate while into the tank riser pipe. Do not force the valve tightening the Spill Container by observing the Auto Limiter II -- Drop Tube into the tank riser pipe. If any obstruction or position of the deflector. Install a Phil-Tite Preassemble Instructions foreign matter interferes with smooth insertion of rotatable swivel adaptor and tighten according to A change in the fill riser length after the valve, the tank riser pipe must be cleared. the manufacturer's installation instructions. Tank Riser 4" inch cutting the drop tube could affect the Install the previously measured, cut and operation of the mechanical overfill threaded fill riser into the tank fill opening WARNING using the spill container installation valve. Failure to follow the assembly and installation instructions. Apply pipe dope to the riser To determine the correct lengths to cut instructions or use of excessive force to insert: NPT male threads. Pipe dope is to be non- the upper and lower sections of the drop the Auto Limiter II® will " VOID THE hardening, gasoline resistant pipe thread tube for installation; use the Work Sheet WARRANTY!" seal compound. for Determining the Drop Tube Lengths Correctly torque the tank riser to ensure a that follows: vapor and liquid tight fit. 10 3