Laserfiche WebLink
May 09 13 01:00p <br />Elite IV Contactors 12094616342 <br />MSZ BLS-xx u) 'MSZ bLIS <br />Page 2 -UE� l } <br />Step 7: Install The Eccentric Insert & Multi -Sync Reducer <br />• Dry fit the Eccentric insert. Make sure it fits properly over the pipe & inside the <br />sleeve. <br />• Dry fit the Multi -Sync Reducer <br />• Adjust the positions so that they lineup properly with the Repair Sleeve & Pipe. <br />Note: A proper fit will not cause extra pressure or force to the sleeve and will <br />Imo' <br />allow a longer lasting repair. <br />:. <br />• Once you have the part lined up correctly <br />1. Pull back the Multi -Sync Reducer & Eccentric Insert <br />2. Apply Zip Tite bonder all around the Eccentric Insert, <br />i <br />3. Slide Eccentric into the Repair sleeve in the proper position <br />4. Apply Zip Tite bonder all around the Multi -Sync Reducer <br />5. Slide the Multi -Sync Reducer into it's proper place <br />6. Set the Clamp the around the sleeve & over the Eccentric Insert and tighten <br />"snugly". <br />7. Set clamp over reducer end on the pipe & tighten enough to create a seal <br />around the pipe. <br />Pipe Size Repair Kit Cuff Insert Eccentric/Insert <br />Multi -Sync Clami <br />3/4" Rigid Conduit MSZ BLS -1.1 UIZ BIS 3.1x1.1 UIZ 3.5x2.6E <br />URZ MS 2.6x1.1 16 <br />1" Ri id Conduit MSZ BLS -1.4 UIZ BLS 3,1x1.4 UIZ 3.5x2.6E <br />URZ MS 2.6x1.4 20 <br />1" Flex Pie MSZ BLS -1.6 UIZ BLS 3.1x1.6 UIZ 3.5x1.6 <br />N/A 24 <br />� it �i° II III, ii I iM1 <br />�i <br />ria9 i+i a i. i <br />a fI At <br />Step 9: Fill With DBF II, Insert Fill Plug <br />TOOLS REQUIRED: <br />• Assemble DAG & DBF II (see instructions on DPM website). <br />Gloves and Static Mixe <br />• Purge 1-2 oz . <br />5/16" Nut driver <br />• Fill fitting slowly. <br />DAG Caulk Gun <br />Note: Use Remote Fill option If access is limited <br />DAGP Caulk Gun <br />• Insert fill plug when filling is completed. <br />DAG III Caulk Gun <br />• Clean any spilled DBF II with DBC and dispose <br />of remaining products per local requirements. <br />PRODUCTS NEEDED: <br />�IIII <br />DBC CleanF <br />I!I <br />Note: After l hour <br />DBB III Bonde <br />the repair job maybe <br />DBF II P0lysu <br />hydro -static tested — <br />I, <br />DBB V Bonde <br />FILL Volume: [per rep; <br />Volume of DBF II neer <br />Volume of DBB III neer <br />Remote Fill Option: <br />Volume of DBB V neer. <br />The following parts are available to order if you can not <br />properly position the assembled DBF II applicator gun to <br />Parts in kit: <br />"fill" the repair. The Remote Fill parts provide a flexible <br />Cuff Insert <br />extension for the filling process. <br />Sleeve <br />RF Adapter 24" tube with male & female ends <br />Eccentric Insert <br />RFA Tube -24 Y:" Tubing in 24" lengths <br />Multi -Sync Reducer <br />RFA Tube %" Tubing in 200' length roll <br />5 clamps <br />Fill Port Plug <br />RFA TubexTube Yz" Tube Coupling <br />Install Instructions <br />RFA xFemale Yi' Tube -Female Fill Port end <br />RFA xMale Y:" Tube -Male Fill Port end <br />RFA xPlug Yz" Tube -Male Plug for fill port <br />p.4 <br />9+ tian of the Eccentric 111ri3ert & Multi ! <br />' I'un{�th+s7>li,f�undthe opening <br />khat there is <br />r ' <br />(for Band Clamps) <br />(for DBF 11) <br />(Pneumatic version for DBF II ) <br />(for DBB V) <br />r <br />Each DBF II & DBB V come <br />fi e Liquid Fill I with a Static Mixer <br />( :ir Poly or Fiberglass sumps) <br />li hoot <br />E — 9.5 oz <br />e <br />e = <br />UIZ BLS 3.1x5ee Table <br />USZ 3.5x3.5 <br />UIZ 3.5xSee Table <br />URZ MS 2.6xSeeTable <br />2 #44, 1 #40, 2 #See Table <br />RFA xPlug <br />