Laserfiche WebLink
May 09 13 01:01p Elite IV Contactors 12094616342 p.5 <br />Multi -Sync Installat, ,i Instructions <br />D� Mr.4orft For Blueline Mecli ,im Fittings <br />IF This kit provides the Multi -Sync Repair for applicat :,ns where the pipe is coming the <br />�ko. „,�5� sump wall straight or at an angle.fC �igt <br />WARNING: Prepare all surfaces to be bonded prior to co.rnl vting installation steps below. <br />Failure to follow each step will void warranty & may result r; premature failure of enetration fit in <br />MSZ BLM-xx 2 <br />Pagel This Kit applies for repairing: Boat kine Medium Fittings <br />General Instructions for: CLEANING: Spray all surfaces to be bonded with DBC Cleaner and allow c) air dry or wipe excess with a clean dry <br />cloth. Surfaces must be dry before applying bonder. <br />General Instructions for: BONDING TO POLY SUMPS OR FIBERGLASS SUMPS: Clean, sand and r o s;h up sump surfaces. Clean fitting and <br />apply ZIP-TITE or DBF II between Bonding Ring & sump wall. <br />STEP 1: Remove Old Boot <br />• Remove clamps <br />• <br />Cutaway old boot <br />• Clean & sand fitting <br />If everything fits continue with <br />the install.. if there is a problem <br />with the fit & function of these <br />parts; either adjust to mak f t lf;, <br />10 lblei.:orxall thebi6MMid' <br />STEP 4: Bond Sleeve ,Cuff Ring & Insert <br />• Apply Zip Tite to split cuff ring. Use 1 of <br />the clamps to hold in place while curing. <br />• Apply Zip -rite to the split insert and use 1 <br />of the clamps to hold in place while <br />curing. <br />• Apply Zi p Tite to the split sleeve and use 2 <br />clamps to hold in place while curing. <br />• Leave these clamps in place for approx 30 <br />minutes for curing before proceeding to <br />the next step <br />STEP 2: Clean all Repair Components <br />• Clean all repair components with DBC <br />prior to installation <br />Split Cleaner Split <br />Cuff Sleeve <br />Ring <br />unrl <br />14•MM A "'l.n <br />s <br />Eccentric Insert Split Multi -Sync <br />Insert Reducer <br />STEP 5: Install The Sleeve, Cuff Ring & Insert <br />• Apply Zip-Tlte to the outer surface of the <br />insert and fully seat inside of cuff <br />• Apply Zip-Tite to the inner surface of the cuff <br />ring and slide all the way onto the cuff <br />• Position the sleeve with the fill port at the top <br />• Once you have the sleeve lined up correctly, <br />1. Apply a bead of Zip-Tite all around the <br />outer surface of the cuff ring <br />2. Slide sleeve over cuff ring & snap in place <br />(fill port at top) <br />3. Set the Clamp the around the sleeve & <br />over the cuff ring and tighten "snugly". <br />STEP iI. 'lace & Dry Fit Cuff Ring ,Sleeve & Insert <br />• W •ac the split cuff ring over the old fitting <br />• Wrac the split insert over the pipe <br />• Wr3t ':he split sleeve over the pipe & up to the <br />bond ig ring with the fill port up <br />STEII 6 Install & Bond Eccentric Insert & Multi -Sync <br />Redu !r Back Together <br />• V%r k Eccentric Insert around the pipe <br />• <br />V% r; 1: Multi -Sync Reducer around the pipe <br />• Alig • Zip -rite to split area on Eccentric Insert, press <br />er;d together & clamp <br />• App , Zip-Tite to split area on Multi -Sync Reducer, <br />pie: ends together & clamp <br />