WORK PLANS - Laserfiche WebLink

Home Browse Search

SPECIFICATIONS PRT 1 GENERAL ROBISON 1.01 SCOPE OF WORK 1.13 RECORD DRAWINGS AND EQUIPMENT DATA 2.03 LIGHTING: 3.04 CONNECTIONS TO EQUIPMENT: ENGINEERING, I N C A. FURNISH AND INSTALL ALL MATERIALS AND EQUIPMENT AND PROVIDE ALL LABOR, TOOLS, TRANSPORTATION, SUPERINTENDENCE AND SERVICES A. MAINTAIN ONE SET OF CLEAN WORKING DRAWINGS AT THE JOB SITE AND ENTER DAILY SUCH "AS-BUILT" INFORMATION AS FEEDER AND A. FURNISH AS DESCRIBED IN THE LIGHTING FIXTURE SCHEDULE. A. GENERAL 19401 40TH AVE W.,SUITE 302 REQUIRED AND NECESSARY TO COMPLETE THE WORK SHOWN ON THE DRAWINGS AND/OR SPECIFIED HEREIN. ALSO INCLUDE ALL OTHER WORK SERVICE ROUTES, PULL BOX LOCATIONS AND CHANGES IN LAYOUT OR ARRANGEMENT WHICH OCCUR DURING CONSTRUCTION. DELIVER LYNNWOOD,WA 98036 AND MISCELLANEOUS ITEMS, NOT SPECIFICALLY MENTIONED, BUT REASONABLY INFERRED FOR A COMPLETE INSTALLATION INCLUDING ALL COMPLETED "RED LINE AS-BUILTS" DRAWINGS TO THE OWNER. B. SUPPORTS: PROPER SUPPORTS AND MOUNTING ACCESSORIES, SUCH AS HANGERS, STEMS, YOKES, PLASTER FRAMES, ETC. SHALL BE 206.364.3343 TEL ACCESSORIES AND APPURTENANCES REQUIRED FOR TESTING THE SYSTEM. IT I THE INTENT A THE DRAWINGS AND ION INCLUDING THAT ALL PROVIDED AS REQUIRED BY THE TYPE OF CEILING INSTALLED. WHERE SWIVEL CANOPIES OR BALL ALIGNERS ARE SPECIFIED, THEY SHALL 1. FURNISH AND INSTALL REQUIRED POWER SUPPLY CONDUIT AND WRING TO ALL EQUIPMENT. SEE BELOW FOR OTHER WIRING REQUIRED. B. SUBMIT TO THE OWNER'S REPRESENTATIVE A SET OF "AS BUILT" DRAWINGS IN VELLUM AND CAD FILE. AS BUILT COMMENTS SHALL BE CAUSE FIXTURE TO HANG PLUMB REGARDLESS OF CEILING SLOPE. CONTACT:TYLER BEAM SYSTEMS BE COMPLETE, AND READY FOR OPERATION. WRITTEN IN A LEGIBLE MANNER IN THE SAME SME AS THE CONTRACT DOCUMENTS. ALSO SUBMIT THREE COPIES OF DATA SHEETS OR OTHER 2. FURNISH AND INSTALL A DISCONNECT SWITCH IMMEDIATELY AHEAD OF AND ADJACENT TO EACH MAGNETIC MOTOR STARTER OR 1.02 REGULATORY REQUIREMENT CURRENT MANUFACTURERS' PUBLICATIONS FOR EACH ITEM OF ELECTRICAL EQUIPMENT FURNISHED FOR THE PROJECT INCLUDING AT LEAST C. FIXTURE DESIGNATION: FIXTURE TYPES ARE DESIGNATED ON DRAWINGS. WHERE ONLY ONE FIXTURE DESIGNATION IS SHOWN, IT APPLIES TC APPLIANCE UNLESS THE MOTOR APPLIANCE IS LOCATED ADJACENT AND WITHIN SIGHT OF THE SERVING PANELBOARD, CIRCUIT A. CODE COMPLIANCE IS MANDATORY. NOTHING IN THESE DRAWINGS AND SPECIFICATIONS PERMITS WORK NOT CONFORMING TO THESE THESE DATA: ALL FIXTURES IN THAT ROOM OR AREA. FOR EXACT FIXTURE COUNT AND LOCATION REFER TO REFLECTED CEILING PLAN. BREAKER OR SWITCH. VERIFY ALL EQUIPMENT NAMEPLATE CURRENT RATINGS PRIOR TO INSTALLATION. OFESS/�N CODES. WHERE WORK IS SHOWN TO EXCEED MINIMUM CODE REQUIREMENTS, COMPLY WITH DRAWINGS AND SPECIFICATIONS. ALL WORK AND 1• TECHNICAL DESCRIPTION AND REPLACEABLE PARTS LIST. 3. INSTALL ALL ROUGH-IN WORK FOR EQUIPMENT FROM APPROVED SHOP DRAWINGS TO SUIT THE SPECIFIC REQUIREMENTS OF THE QR MATERIALS SHALL COMPLY WITH THE LATEST RULES, CODES AND REGULATIONS, INCLUDING, BUT NOT LIMITED TO THE FOLLOWING: D. WIRE 1-LAMP AND 3-LAMP FLUORESCENT FIXTURES IN TANDEM WHERE REQUIRED BY CODE. EQUIPMENT. O �.� E R e�l 1. OCCUPATIONAL SAFETY AND HEALTH ACT STANDARDS (OSHA). r 2. PHYSICAL DESCRIPTION AND INSTALLATION INSTRUCTIONS. 4. FURNISH AND INSTALL MANUAL THERMAL PROTECTION FOR ALL MOTORS NOT INTEGRALLY EQUIPPED WITH THERMAL PROTECTION. 2. NEPA 170: NATIONAL ELECTRIC CODE (NEC) 3. USERS MANUAL AND OPERATING INSTRUCTIONS. E. BALLASTS: ADVANCE, GE, OR APPROVED HIGH FREQUENCY ELECTRONIC, FULL LIGHT OUTPUT, ENERGY SAVING, CLASS "P", HIGH POWER 5. FURNISH 120 VOLT POWER TO EACH CONTROL PANEL AND TIME SWITCH REQUIRING A SOURCE OF POWER TO OPERATE. 4. MANUFACTURER'S WARRANTY. FACTOR, ETL CERTIFIED, SOUND RATING "A" OR AS INDICATED ON DRAWINGS. F. G. G. z 3. CGBC w No. E-21545 m 4. STATE BUILDING CODE 1.14 CLEAN-UP F. EMERGENCY LIGHTING SHALL PROVIDE INITIAL ILLUMINATION OF AT LEAST AN AVERAGE OF 1 FOOT-CANDLE AND A 3.05 INSTALLATION OF WIRES: 5. NFPA ;101: LIFE SAFETY CODE. MINIMUM AT ANY POINT OF 0.1 FOOT-CANDLE MEASURED ALONG THE PATH OF EGRESS AT FLOOR LEVEL 6. STATE FIRE MARSHAL A. RID THE PREMISES OF SCRAP MATERIALS, TRASH AND DEBRIS BOTH DURING CONSTRUCTION AND AT COMPLETION OF THE PROJECT. ILLUMINATION LEVELS MAY DECLINE TO 0.6 FOOT-CANDLE AVERAGE AND A MINIMUM OF 0.06 FOOT-CANDLE AT THE A. PULL NO WIRE INTO ANY PORTION OF THE CONDUIT SYSTEM UNTIL ALL CONSTRUCTION WORK WHICH MIGHT DAMAGE THE WIRE HAS 7. LOCAL UTILITY COMPANIES LEAVE THE BUILDING AND SURROUNDING AREA IN A CLEAN AND ORDERLY CONDITION. END OF 90 MINUTES. THIS COMMENT ALSO APPLIES TO SHEET A6.0. THIS SHALL BE VERIFIED DURING ONSITE BEEN COMPLETED. T F�ECTR�OPNe 1.15 GUARANTEE INSPECTIONS. 9PF p� 1.03 LICENSE, FEES, AND PERMITS G. ELECTRICAL CONTRACTOR SHALL PROVIDE, TO THE LOCAL CITY FIRE MARSHAL'S OFFICE, DOCUMENTATION OF EMERGENCY B. INSTALL ALL WIRE CONTINUOUS FROM OUTLET TO OUTLET OR TERMINAL TO TERMINAL SPLICES IN CABLES WHEN REQUIRED SHALL 0 CA��F A. ELECTRICAL CONTRACTOR SHALL PAY FOR ALL LICENSES, PERMITS AND INSPECTION FEES REQUIRED BY THE AUTHORITY HAVING A. GUARANTEE THE INSTALLATION FREE FROM DEFECTS OF WORKMANSHIP AND MATERIALS FOR A PERIOD OF ONE YEAR AFTER DATE OF BE MADE IN HANDHOLES, PULL BOXES OR JUNCTION BOXES. MAKE BRANCH CIRCUIT SPLICES IN OUTLET BOXES WITH 8" OF Seal JURISDICTION AND SHALL ARRANGE FOR ALL REQUIRED INSPECTIONS. CERTIFICATION OF FINAL PAYMENT AND PROMPTLY REMEDY ANY DEFECTS DEVELOPING DURING THIS PERIOD, WITHOUT CHARGE. LIGHTING LEVEL COMPLIANCE BY WAY OF AFTER-HOURS LIGHT METER TEST OR PHOTOMETRIC DOCUMENTATION IN ACCORDANCE WITH CBC $ 1008.3.2, PRIOR TO SCHEDULING THE FINAL LIFE SAFETY INSPECTION. PLEASE ADD THIS REQUIREMENT TO THE CORRECTLY COLOR-CODED TAILS LEFT IN THE BOX. 1.04 SAFETY AND INDEMNITY GENERAL NOTES. AWAITING DOCUMENTATION FROM ELECTRICAL CONTRACTOR UPON INSTALLATION, BALANCING, AND A. THE CONTRACTOR SHALL BE SOLELY AND COMPLETELY RESPONSIBLE FOR CONDITIONS OF THE JOB SITE, INCLUDING SAFETY OF ALL 1.16 TEMPORARY SERVICES COMMISSIONING. THIS SHALL BE VERIFIED DURING ONSITE INSPECTIONS. C. SPLICES IN WIRES AND CABLES SHALL BE MADE UTILIZING MATERIALS AND METHODS DESCRIBED HEREIN BEFORE. bpPERSONS AND PROPERTY DURING PERFORMANCE OF WORK. THIS REQUIREMENT WILL APPLY CONTINUOUSLY AND NOT BE LIMITED TO NORMAL A. PROVIDE ADE ATE AND SAFE TEMPORARY ELECTRICAL POWER AND LIGHTING THROUGHOUT THE CONSTRUCTION AND FINISHING OF THE WORKING HOURS. NO ACT, SERVICE, DRAWING REVIEW OR CONSTRUCTION REVIEW BY THE OWNER, THE ENGINEERS OR THEIR CONSULTANTS, IS � H. EXIT SIGNS SHALL BE PROVIDED WHERE THE EXITS AND/OR EXIT PATHS OF EGRESS TRAVEL THAT ARE NOT IMMEDIATELY D. MAKE ALL GROUND, NEUTRAL AND LINE CONNECTIONS TO RECEPTACLE AND WIRING DEVICE TERMINALS AS RECOMMENDED BY PREMISES. IN ADDITION TO SPECIAL OR UNUSUAL REQUIREMENTS, PROVIDE AT LEAST THESE ITEMS: VISIBLE TO THE OCCUPANTS SO THAT ALL ACCESS TO EXITS ARE READILY VISIBLE IN ACCORDANCE WITH IBC 101& THIS MANUFACTURER. PROVIDE GROUND JUMPER FROM OUTLET BOX TO GROUND TERMINAL OF DEVICES WHEN THE DEVICE IS NOT INTENDED TO INCLUDE REVIEW OF THE ADEQUACY OF THE CONTRACTOR'S SAFETY MEASURES, IN, ON, OR NEAR THE CONSTRUCTION SITE. 1• THREE (3) 20-AMP CIRCUITS FOR CONSTRUCTION POWER TOOLS. PROVIDE GFl TEMPORARY CIRCUITS WITH COVERPLATES TO MEET SHALL BE VERIFIED DURING ONSITE INSPECTIONS. APPROVED FOR GROUNDING THROUGH THE MOUNTING SCREWS. 1.05 DRAWINGS AND SPECIFICATIONS OSHA REQUIREMENTS. A. ALL DRAWINGS AND ALL DIVISIONS OF THESE SPECIFICATIONS SHALL BE CONSIDERED AS A WHOLE AND WORK OF THIS DIVISION SHOWN 2. THREE OR MORE LIGHT STRINGS SUSPENDED APPROXIMATELY ONE FOOT BELOW THE HEIGHT OF FINISH CEILING WITH LAMPS SPACED NOT 2.04 FIRE ALARM SYSTEM: (WHEN REQUIRED) E. PROVIDE BRADY WIRE MARKERS WHERE NUMBER OF CONDUCTORS IN A BOX EXCEEDS FOUR. ANYWHERE THEREIN SHALL BE FURNISHED UNDER THIS DIVISION. DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL ARRANGEMENT OF MORE THAN TWELVE FEET ON CENTERS. STRINGS SHALL BE RUN THE LENGTH OF THE STORE SPACE PARALLEL TO THE DEMISING WALLS, DESIGN/BUILT BY LICENSED FIRE ALARM CONTRACTOR AS REQUIRED BY THE CITY. F. MEGGER AND RECORD INSULATION RESISTANCE OF ALL 600 VOLT INSULATED CONDUCTORS SIZE X4/0 AND LARGER USING 500 VOLT EQUIPMENT AND WIRING. MOST DIRECT ROUTING OF CONDUITS AND WIRING IS NOT ASSURED. EXACT REQUIREMENTS SHALL BE GOVERNED BY WITH ONE STRING WITHIN EIGHT FEET OF EACH WALL AND ONE (OR MORE) INTERMEDIATE STRING(S) ARRANGED TO LIMIT THE SPACING CONDITIONS OF THE JOB. CONSULT ALL OTHER DRAWINGS IN PREPARATION OF THE BID. EXTRA LENGTHS OF WIRING OR ADDITION OF PULL OR BETWEEN ROWS TO SIXTEEN FEET OR LESS. A. IT SHALL BE RESPONSIBILITY OF THE GENERAL CONTRACTOR AND HIS FIRE ALARM CONTRACTOR TO OBTAIN THE REQUIREMENTS AND MEGGER FOR ONE MINUTE. MAKE TESTS WITH CIRCUITS ISOLATED FROM SOURCE AND LOAD. JUNCTION BOXES, ETC., NECESSITATE BY SUCH CONDITIONS SHALL BE INCLUDED IN THE BID. APPROVAL FROM THE LOCAL FIRE MARSHAL ON ALL FIRE ALARM DEVICES AND WIRING REQUIRED. 1.06 CONDITIONS AT SITE PART 2 PRODUCTS B. THE CONTRACTOR SHALL SUBMIT DRAWINGS TO THE CITY FOR DEFERRED APPROVAL OF THE COMPLETE FIRE ALARM SYSTEM DESIGN. 3.06 INSTALLATION OF RECESSED LIGHT FIXTURES AND DEVICES A. VISIT SITE OF THE WORK, COMPARE IT WITH THE DRAWINGS AND SPECIFICATIONS AS TO THE CONDITIONS UNDER WHICH WORK IS TO BE 2.01 MATERIAL APPROVAL A. ALL RECESSED LIGHT FIXTURES, BOXES, RECEPTACLES & OTHER DEVICES MOUNTED IN THE FIRE RATED CEILINGS OR WALLS PERFORMED, ASCERTAIN AND CHECK ALL CONDITIONS AND ELEVATIONS AND TAKE ALL MEASUREMENTS WHICH MAY AFFECT THE WORK. NO PART 3 EXECUTION SHALL BE PROVIDED WITH AN APPROVED ENCLOSURE CARRYING THE SAME FIRE RATING AS THE CEILING OR WALL ALLOWANCE SHALL SUBSEQUENTLY BE MADE FOR ANY EXTRA EXPENSE OR CLAIMS DUE TO FAILURE OR NEGLECT UNDER THIS REQUIREMENT A. ALL MATERIALS MUST BE NEW AND BEAR UNDERWRITER'S LABORATORIES LABEL MATERIALS THAT ARE NOT COVERED BY UL TESTING TO MAKE SUCH EXAMINATION, INCLUDING EXAMINATION OF RESTRICTED WORKING CONDITIONS OR SUCH OTHER DIFFICULTIES VISUALLY STANDARDS SHALL BE TESTED AND APPROVED BY AN INDEPENDENT TESTING LABORATORY OR A GOVERNMENTAL AGENCY. MATERIAL NOT IN 3.01 GENERAL B. OUTLET BOXES THAT OCCUR ON OPPOSITE SIDES OF THE WALL WITHIN 24 INCH HORIZONTAL DISTANCE OF ONE ANOTHER OBSERVED DURING SITE VISIT. CONTRACTOR IS RESPONSIBLE FOR BECOMING COMPLETELY FAMILIAR WITH THE ARCHITECTURAL AND ACCORDANCE WITH THESE SPECIFICATIONS MAY BE REJECTED EITHER BEFORE OR AFTER INSTALLATION. SHALL BE PROTECTED BY AN APPROVED FIRESTOP MATERIAL OR DETAIL TO MAINTAIN THE FIRE RATING OF THE WALL STRUCTURAL CONDITIONS AND LIMITATIONS WHICH WILL EXIST IN THE BUILDING AND TO PROVIDE ALL LABOR, TOOLS AND MATERIALS REQUIRED A. ELECTRIC SYSTEM LAYOUTS INDICATED ON THE DRAWINGS ARE GENERALLY DIAGRAMMATIC AND SHALL BE FOLLOWED AS CLOSELY AS ACTUAL TO PRODUCE A COMPLETELY CONCEALED INSTALLATION AS INDICATED ON THE PLANS, SPECIFICATIONS, AND REQUIRED BY THE CODE. 2.02 BASIC ELECTRICAL MATERIALS CONSTRUCTION AND WORK OF OTHER TRADES WILL PERMIT. GOVERN EXACT ROUTING OF CABLE AND WIRING AND THE LOCATIONS OF OUTLETS 3.07 WIRE COLOR CODE: 1.07 WORKMANSHIP AND CONTRACTOR'S QUALIFICATIONS A. CONDUITS AND RACEWAYS BY THE STRUCTURE AND EQUIPMENT SERVED. TAKE ALL DIMENSIONS FROM ARCHITECTURAL DRAWINGS. A. ONLY QUALITY WORKMANSHIP WILL BE ACCEPTED. HAPHAZARD OR POOR INSTALLATION WILL BE CAUSE FOR REJECTION OF WORK. 1. RIGID STEEL: HOT-DIPPED GALVANIZED. B. CONSULT ALL OTHER DRAWINGS, VERIFY SCALES AND REPORT ANY DIMENSIONAL DISCREPANCIES OR OTHER CONFLICTS WITH OWNER BEFORE COLOR CODING SHALL BE CONTINUOUS FOR WIRE #12 THROUGH #10 AWG. PHASE CONDUCTORS #8 AND LARGER AND CONDUCTORS SUBMITTING BID. OF ANY SIZE IN CABLE ASSEMBLIES MAY HAVE COLORED PHASING TAPE AT TERMINATIONS. COLOR CODE WIRES AS FOLLOWS: 1.08 REQUIRED SUBMITTALS 2. INTERMEDIATE METAL CONDUIT (IMC): HOT-DIPPED GALVANIZED. C. ALL HOME RUNS TO PANELBOARDS ARE INDICATED AS STARTING FROM THE OUTLET NEAREST THE PANEL AND CONTINUING IN THE GENERAL A. SUBMITTALS, UNLESS OTHERWISE NOTED, SHALL BE A SINGLE PACKAGE OF SIX (6) COPIES SUBMITTED TO OWNER FOR REVIEW. WORK SHALL 3. ELECTRICAL METALLIC TUBING (EMT): ELECTRO-GALVANIZED. DIRECTION OF THAT PANEL CONTINUE SUCH CIRCUITS TO THE PANEL AS THOUGH THE ROUTES WERE COMPLETELY INDICATED. TERMINATE VOLTAGE PHASE A PHASE B PHASE C NEUTRAL GROUND NOT COMMENCE UNLESS SUBMITTALS HAVE BEEN APPROVED. 4. RIGID NON METALLIC CONDUIT (PVC SCHEDULE 40) HOMERUNS OF SIGNAL, ALARM, AND COMMUNICATION SYSTEMS IN A SIMILAR MANNER. 120/208V BLACK RED BLUE WHITE GREEN B. SUBMIT CUTSHEETS, MATERIAL DATA, AND SHOP DRAWINGS, AS NOTED BELOW. FOR REVIEW WITHIN FIFTEEN (15) DAYS AFTER AWARD OF 5. WIREWAY: CODE GAUGE STEEL, WITH KNOCKOUTS AND HINGED COVER, CORROSION RESISTANT GRAY BAKED ENAMEL FINISH. D. AVOID CUTTING AND BORING HOLES THROUGH STRUCTURE OR STRUCTURAL MEMBERS WHEREVER POSSIBLE. OBTAIN PRIOR APPROVAL OF < CONTRACT. SUBMITTALS REQUIRED AS FOLLOWS: 6. PROVIDE FITTINGS AND ACCESSORIES APPROVED FOR THE PURPOSE EQUAL IN ALL RESPECTS TO THE CONDUIT OR RACEWAY. EMT OWNER AND CONFORM TO ALL STRUCTURAL REQUIREMENTS WHEN CUTTING OR BORING THE STRUCTURE IS NECESSARY AND PERMITTED. 1. BASIC ELECTRICAL MATERIALS INCLUDING BUT IS NOT LIMITED TO: CONNECTORS AND COUPLINGS SHALL BE STEEL SET SCREW OR STEEL COMPRESSION TYPE INDOORS AND STEEL COMPRESSION TYPE IN WET E. FURNISH AND INSTALL ALL NECESSARY HARDWARE, HANGERS, BLOCKING, BRACKETS, BRACING, RUNNERS, ETC. REQUIRED FOR EQUIPMENT 3.08 IDENTIFICATION: m LOCATIONS AND OUTDOORS. SPECIFIED UNDER THIS SECTION. INSTALLATION SHALL MEET SEISMIC 4 REQUIREMENTS. A.) WIRING DEVICES - RECEPTACLES, SWITCHES, FACEPLATES F. PROVIDE NECESSARY BACKING REQUIRED TO INSURE RIGID MOUNTING OF OUTLET BOXES. A. PROVIDE NAMEPLATES FOR SWITCHBOARDS, PANELBOARDS, AND ALL SIMILAR DEVICES. NAMEPLATES SHALL BE SCREWED (NO cCn B.) WIRES, CONNECTORS, TAPES, SPLICES, TERMINATIONS, AND ACCESSORIES B. WIRES AND CABLES: G. ELECTRICAL INSTALLATION IN PUBLIC LOCATIONS SHALL BE ACCESSIBLE AND INSTALLATION SHALL COMPLY WITH AMERICAN DISABILITIES ACT ADHESIVES) ENGRAVED BAKELITE OR PHOTO-ETCHED METALLIC NAMEPLATE IDENTIFICATION SHOWING PANEL DESIGNATION, VOLTAGE C.) RACEWAYS AND ACCESSORIES 1. FOR POWER AND LIGHTING SYSTEM 600V OR LESS: (ADA) REQUIREMENTS. ELECTRICAL INSTALLATION SHALL COMPLY WITH APPLICABLE CODES AS LISTED IN CONSTRUCTION DOCUMENTS. AND PHASE IN MINIMUM 1/4" HIGH LETTERS. 0 D.) DEVICE IDENTIFICATION A.) CONDUCTOR: MINIMUM SIZE #12 AWG. B. PROVIDE DYMO LABELS ON ALL LIGHTING SWITCHES AND CONVENIENCE AND SPECIAL PURPOSE RECEPTACLES TO SHOW PANEL AND w Q 2. ELECTRICAL EQUIPMENT 1. #12 AND #10 AWG SOLID COPPER 3.02 WIRING METHODS CIRCUIT NUMBER TO WHICH THE DEVICE IS CONNECTED. 00� CD A.) POWER DISTRIBUTION EQUIPMENT - PANELBOARDS, SWITCHBOARDS, DISCONNECT SWITCHES, CIRCUIT BREAKERS, ii. II8 AWG AND LARGER SHALL BE STRANDED COPPER OR ALUMINUM. " " o POWER DISTRIBUTION UNITS, ETC. B.) INSULATION TYPE: A. WHEN CONDITIONS DETERMINED IN A ABOBE ARE NOT MET, INSTALL ALL WIRING IN RACEWAY, OR USE MC CABLE WHERE APPROVED BY ALL C. EACH PANELBOARD SHALL CONTAIN A METAL-FRAMED CIRCUIT DIRECTORY INSIDE COVER, WITH PLASTIC PROTECTOR. J B. SERVICE ENTRANCE EQUIPMENT - TERMINATION CANS, METERED SWITCHBOARDS, ETC. i. 2 TO AWG: THWN FOR WET OR UNDERGROUND AND THHN FOR DRY LOCATIONS. APPLICABLE CODES AND REGULATIONS. CONDUIT SHALL BE RIGID STEEL, IMC OR EMT AS FOLLOWS: ' 1. ABOVE GROUND: USE RIGID STEEL, IMC OR EMT. D. PANELBOARD SCHEDULE: AFTER COMPLETION OF WORK, PROVIDE TYPEWRITTEN UPDATED PANELBOARD SCHEDULES FOR ALL m 3. LIGHTING ii. #1/0 THROUGH ,#4/0 AWG: XHHW (55 MILS). 2. WET LOCATIONS: RIGID STEEL OR IMC ONLY. PANELBOARDS. J A.) LIGHT FIXTURES AND SUPPORT DEVICES iii. X250 MCM AND LARGER: XHHW (65 MILS). 3. LOCATIONS SUBJECT TO MECHANICAL INJURY (0 TO 3 FT ABOVE FINISH FLOOR): RIGID STEEL OR IMC ONLY. Q B.) LAMPS AND BALLASTS - INCLUDE BALLASTS CERTIFICATION. BALLAST SHALL HAVE LOCAL DISCONNECTS. iv. GROUNDING WIRE: TW. 4. DRY LOCATIONS AND NOT SUBJECT TO MECHANICAL INJURY: EMT, IMC OR RIGID STEEL CONDUIT. 3.09 GROUNDING: z C.) CONTROLS - OCCUPANCY SENSORS, PHOTOCELL, LIGHTING CONTACTORS, LIGHTING CONTROL PANELS, DIMMERS, ETC. v.) METAL CLAD (MC) CABLES 5. UNDERGROUND: USE PVC SCH. 40 WITH RIGID STEEL AT LAST TRANSITION TO ABOVE GROUND. D.) FIXTURE AND ASSEMBLY WATTAGES A. ELECTRICAL SERVICE AND SEPARATELY DERIVED ALTERNATING CURRENT SYSTEM SHALL BE GROUNDED IN ACCORDANCE WITH NEC E.) FOR PROJECTS THAT ARE SUBJECT TO STATE ENERGY CODES, PROVIDE SUBMITTALS CONFIRMING THAT PRODUCTS 2. FOR SIGNAL AND COMMUNICATIONS CIRCUIT- 6. IN SLAB & INSIDE WALLS - PVC SCH. 40. ARTICLE 250-3 TO 250-26, INCLUSIVE. N SUBMITTED MEET THE REQUIRED MANDATORY MEASURES AS WELL AS MEETS MAXIMUM STATED ENERGY CONSUMPTIONS A.) SPECIAL CABLES SHALL BE AS SPECIFIED ON DRAWINGS. B. USE FLEXIBLE CONDUITS OR MC CABLE IN THE FOLLOWING APPLICATIONS: B. GROUND NON-CURRENT CARRYING METAL PARTS OF ELECTRICAL EQUIPMENT ENCLOSURES, FRAMES, CONDUCTOR RACEWAYS OR SHOWN IN WSEC LIGHTING COMPLIANCE CALCULATIONS. CABLE TRAYS TO PROVIDE A LOW IMPENDANCE PATH FOR LINE-TO-GROUND FAULT CURRENT AND TO BOND ALL NON-CURRENT o C. SUBMIT COMPLETE TEST REPORTS AND ANALYSIS FOR REVIEW WITHIN FIFTEEN (15) DAYS AFTER TESTING. B.) CONDUCTORS FOR GENERAL USE SHALL BE STRANDED COPPER CONDUCTOR, #16 AWG MINIMUM, NTH THWN INSULATION FOR 1. FINAL CONNECTIONS TO MOTOR. CARRYING METAL PARTS TOGETHER. PROVIDE GROUND CONDUCTOR IN EACH RACEWAY SYSTEM IN ADDITION TO CONDUCTORS SHOWN. 2. FINAL CONNECTIONS INTO AND OUT OF THE TRANSFORMER. a a a a a a a � UNDERGROUND OR WET LOCATIONS AND THHN INSULATION FOR DRY LOCATIONS. EQUIPMENT GROUND CONDUCTOR SHALL BE ELECTRICALLY AND MECHANICALLY CONTINUOUS FROM THE ELECTRICAL CIRCUIT SOURCE w D. SUBMIT WSEC LIGHTING COMPLIANCE FORMS AT VARIOUS STAGES OF THE PROJECTS, OR AS REQUESTED. Q = 3. FINAL CONNECTIONS TO VIBRATING EQUIPMENT. TO THE EQUIPMENT TO BE GROUNDED. SIZE GROUND CONDUCTORS PER NEC ARTICLE 250-95 UNLESS LARGER CONDUCTORS ARE E SUBMIT VERIFIED PUNCHDAT TWO (2) WEEKS AFTER ISSUANCE DATE. INDICATE PUNCHLIST ITEMS THAT HAVE BEEN COMPLETED BY 3 EXCEEDING APPLICABLE IPCEAACCEPTABLE PRODUCTS: ESTAND RDS.RAL IC, ANACONDA, OKONITE, PRANITE OR TRIANGLE PRODUCTS CONFORMING OR 4. INTER-CONNECTIONS BETWEEN ALL LIGHT FIXTURES (NOT TO INCLUDE HOMERUN FROM FIXTURE OR DEVICE TO PANELBOARD, WHICH SHOWN ON DRAWINGS. CONTRACTOR. INCLUDE DATE FOR REPUNCH. o C.) OUTLET BOXES, JUNCTION AND PULLBOXES MUST BE RIGID). C. GROUNDING CONDUCTORS SHALL BE IDENTIFIED WITH GREEN INSULATION. WHERE GREEN INSULATION IS NOT AVAILABLE ON LARGER 1.09 SUBSTITUTIONS 1. OUTLET BOXES: 4" SQUARE X 1-1/2" DEEP (OR LARGER) GALVANIZED SHEET STEEL KO-TYPE WITH PLASTER RING AND COVER 5. FINAL CONNECTIONS WHERE RIGID CONDUIT IS NOT PRACTICAL SIZES, BLACK INSULATION SHALL BE USED SUITABLY IDENTIFIED WITH GREEN TAPE AT EACH JUNCTION BOX OR DEVICE ENCLOSURE. M A. ONE OR MORE MAKES OF MATERIALS OR METHODS MAY HAVE BEEN SPECIFIED TO ESTABLISH THE STANDARD OF QUALITY, FOR GENERAL INTERIOR USE AND CAST METAL TYPE FS OR FD WITH MATCHING SCREW COVERS FOR EXTERIOR AND EXPOSED 6. IN WALLS (FOR LIGHT SWITCHES AND 120V POWER RECEPTACLES AND HVAC CONTROL EQUIPMENT). a WORKMANSHIP, FINISH, AND DESIGN REQUIRED, BUT OTHER MATERIALS OR METHODS EQUAL OR BETTER IN QUALITY, WORKMANSHIP, FINISH, M DESIGN, AND GUARANTEED PERFORMANCE, MAY BE SUBMITTED FOR REVIEW AND APPROVAL AS SUBSTITUTION. ALL SUBSTITUTIONS ARE INTERIOR LOCATIONS (GASKETED IN DAMP OR WET LOCATIONS). END OF SECTION SUBJECT TO REVIEW AND APPROVAL BY ARCHITECT, ENGINEER, AND OWNER. 2. JUNCTION BOXES (FLOOR BOX NOT INCLUDED) SHALL BE SAME AS OUTLET BOXES UP TO 42 CU. IN. AND CODE-GAUGE STEEL IN 3.03 INSTALLATION OF CONDUITS: co B. SUBSTITUTIONS SHALL BE REQUESTED IN A WRITTEN FORM AND SHALL BE ACCOMPANIED WITH A SIGNED STATEMENT THAT PROPOSED LARGER SIZES WITH SURFACE OR FLUSH-TYPE SCREW-MOUNTED TRIMCOVERS, BOTH BOXES AND COVERS INHIBITOR-PRIMED AND A. GENERALc SUBSTITUTION IS EQUAL, OR BETTER THAN SPECIFIED. ADDITIONAL DOCUMENTATION TO SUBSTANTIATED PROPOSED SUBSTITUTION MAY BE PAINTED INSIDE OUT. a 1. RUN ALL CONDUIT CONCEALED UNLESS OTHERWISE NOTED OR SHOWN. 0 REQUIRED BY OWNER, ARCHITECT, AND ENGINEER. CONTRACTOR SHALL SUBMIT AS DIRECTED. 3. PULL BOXES SHALL BE SAME AS JUNCTION BOXES UNLESS INDICATED OTHERWISE ON THE DRAWINGS, WITH COVERS. 2. RUN ALL CONDUIT PARALLEL TO OR AT RIGHT ANGLES TO CENTER LINES OF COLUMNS AND BEAMS. C. CONTRACTOR SHALL ACCOMPANY REQUEST FOR SUBSTITUTION LETTER WITH A COMPLETED CSI SUBSTITUTION FORM INCLUDE 3. CONDUITS ABOVE CEILINGS SHALL NOT OBSTRUCT REMOVAL OF CEILING TILES, LIGHTING FIXTURES, AIR DIFFUSERS, ETC. Q W M THE COMPARISON FOR FOLLOWING: 4. TELEPHONE OUTLET BOXES SHALL BE THE TYPE AND SIZE REQUIRED BY THE SERVING TELEPHONE COMPANY BUT NOT SMALLER 4. CONDUITS SHALL NOT CROSS ANY DUCT SHAFT OR AREA DESIGNATED AS FUTURE DUCT SHAFT HORIZONTALLY. CONDUIT RISERS 0 3 1. ELECTRICAL RATING THAN 4-11/16" SQUARE X 2-1/8" DEEP WITH SINGLE-GANG RING AND SIERRA #S-754N SPLIT PLATE BUSHING. WHEN ALLOWED IN DUCT SHAFT MUST BE COORDINATED WITH MECHANICAL WORK TO AVOID ANY CONFLICT. 0 V) 2. FINISHES 5. UNDERGROUND AND SITE JUNCTION BOXES, HANDHOLES, AND MANHOLES B. CONDUIT SUPPORTS: II II W C'7 0 3.SPARE PARTS 1. SUPPORT CONDUITS WITH UNDERWRITER'S LABORATORIES LISTED STEEL CONDUIT SUPPORTS AT INTERVALS REQUIRED BY THE Y Y Y > C'7 A.) SHALL BE MADE UP OF PRECAST CONCRETE WITH TRAFFIC RATED STEEL COVERS. EXTENSIONS SHALL BE PROVIDED AS U 4. PERFORMANCE DATA NATIONAL ELECTRIC CODE. WIRES OR SHEET METAL STRIPS ARE NOT ACCEPTABLE FOR CONDUIT SUPPORT. USE CONDUIT Q Lo 5. COSTS AND SCHEDULE NECESSARY TO MAIN REQUIRED COVERAGE FOR DUCT BANKS. HANGERS FOR ALL CONDUITS NOT DIRECTLY FASTENED TO STRUCTURE AND FOR ALL MULTIPLE CONDUIT RUNS. DO NOT ATTACH 0 B.) PROVIDE 10" X 17' (MIN) FOR PULLBOXES, 36" X 60" (MIN) FOR HANDHOLES, AND 6'X8'X6' (MIN) MANHOLES. ANY CONDUIT TO MECHANICAL DUCTS OR PIPES. w D. A WRITTEN SIGNED STATEMENT FROM THE GENERAL CONTRACTOR SHALL ACCOMPANY SUBSTITUTION REQUEST FORM ASSURING THAT: 2. INDIVIDUAL CONDUITS 1/2 AND 3/4 SIZE FOR LIGHTING MAY BE SUPPORTED FROM CEILING SUPPORT WIRES WITH CADDY CLIPS N 1. HE HAS VERIFIED DIMENSIONS WITH PROJECT CONDITIONS AND HAS COORDINATED WITH OTHER TRADES. SUBSTITUTION DOES NOT D. WIRING DEVICES AND PLATES ONLY IF ACCEPTABLE TO LOCAL CODE. ONLY ONE CONDUIT IS PERMITTED TO BE ATTACHED TO ANY CEILING SUPPORT WIRE. h ~ 0 /Q Ci AFFECT DIMENSIONS SHOWN ON DRAWINGS. HANG SUCH CONDUIT SO AS NOT TO AFFECT LEVEL OF CEILING. Q 0 U 0 1. WIRING DEVICES AND PLATES SHALL BE LISTED FOR SPECIFIC USE. L n 41= w 2. HE SHALL PAY AND BURDEN THE COSTS FOR CHANGES TO THE PROJECT INCLUDING RE-DESIGN, RE-ENGINEERING AND REVIEW OF 3. AVOID ATTACHING CONDUIT TO FAN PLENUMS. EN IT IS NECESSARY TO SUPPORT CONDUIT FROM FAN PLENUM, PROVIDE A J WH o SUBSTITUTION. ONLY ONE (1) ENGINEERING REVIEW TIME IS ALLOWED FOR EACH PRODUCT SUBSTITUTION. CONTRACTOR SHALL BE 2• ALL POWER RECEPTACLES AND SWITCHES FOR GENERAL PURPOSE CIRCUITS SHALL BE NEMA SPECIFICATION GRADE, RATED AS FOLLOWS: LENGTH OF FLEXIBLE CONDUIT BETWEEN PORTION ATTACHED FAN PLENUM AND PORTION ATTACHED TO THE BUILDING TO MINIMIZE Q O RESPONSIBLE FOR ADDITIONAL REVIEW TIME AND SHALL PAY ARCHITECT AND ENGINEER'S TIME AT THEIR PROFESSIONAL RATE A.) GENERAL PURPOSE RECEPTACLES: NEMA 5-15R OR 5-20R TRANSMISSION OF VIBRATION TO THE BUILDING STRUCTURE. ILL � 0 SCHEDULE. ® B.) DEDICATED RECEPTACLES: NEMA 5-20R C. CONDUIT PENETRATION: W CO W W 0 3. HE HAS CONFIRMED THAT THE PROPOSED SUBSTITUTION WILL HAVE NO ADVERSE AFFECT ON OTHER TRADES, THE CONSTRUCTION 1. PENETRATING FIRE RATED FLOOR OR WALL INSTALL CONDUIT IN CONDUIT SLEEVE OR FRAMED OPENING. SEAL PENETRATION WITH Er a SCHEDULE, OR SPECIFIED WARRANTY REQUIREMENTS. 3. SWITCHES: TWENTY (20) AMPERE. FIRE RETARDANT SEALANT SPECIFIED HEREIN. z PENETRATING ROOF OR EXTERIOR WALL: AVOID PENETRATING ROOF OR EXTERIOR WALL WHERE POSSIBLE. WHERE PENETRATIONS U 4. HE HAS CONFIRMED THAT MAINTENANCE AND SERVICE PARTS WILL BE LOCALLY AVAILABLE FOR THE PROPOSED SUBSTITUTION. A.) IN MECHANICAL AND ELECTRICAL EQUIPMENT ROOMS, ILLUMINATED LIGHT SWITCHES SHALL BE PROVIDED. 2. ARE NECESSARY, BUILDING WEATHERPROOF INTEGRITY MUST BE PRESERVED. Q 0 E. COST SAVINGS RESULTING FROM SUBSTITUTION SHALL BE RETURNED TO THE CONTRACT OR THE OWNER IF THE SUBSTITUTION IS 4. ALL GENERAL PURPOSE TWENTY (20) A. 125/250 V RECEPTACLES AND 120/277V SWITCHES SHALL CONFORM TO NEMA WD-1 3. PENETRATING SOUND INSULATED OR AIR PLENUM WALL: INSTALL CONDUIT IN CONDUIT SLEEVE AND SEAL PENETRATION AS 0 Q w PERMITTED. SPECIFICATIONS. DETAILED ON THE DRAWINGS. F. NO WORK INVOLVING MATERIALS SUBMITTED FOR SUBSTITUTION SHALL PROCEED UNTIL WRITTEN ACCEPTANCE IS RECEIVED FROM THE 4. PENETRATING NON-FIRE RATED DRY WALL CONDUIT SLEEVES ARE NOT REQUIRED. PENETRATIONS MUST BE SEALED WITH U OWNER. THE OWNER IS THE FINAL JUDGE OF ACCEPTABILITY OF PREFERRED SUBSTITUTIONS. 5. UNLESS OTHERWISE INDICATED, WIRING DEVICES AND COVER PLATES SHALL BE FURNISHED AND INSTALLED IN COLOR TO MATCH FINISH PLASTER PRIOR TO PAINTING. PENETRATIONS MADE AFTER WALL FINISH IS APPLIED MUST BE AS SMALL AS POSSIBLE AND W Q o SURFACE WHERE IT IS LOCATED ON, I.E., DARK BROWN, BEIGE, WHITE OR STAINLESS STEEL PROVIDED WITH ESCUTCHEONS, ONE ON EACH SIDE OF WALL. Ui a 1.10 COORDINATION 5. PENETRATING SUSPENDED CEILING: CUT HOLE AS SMALL AS POSSIBLE TO PERMIT CONDUIT PENETRATION. PROVIDE ESCUTCHEON a A. COORDINATE WORK WITH OTHER TRADES TO AVOID CONFLICT AND TO PROVIDE CORRECT ROUGH-IN AND CONNECTION FOR EQUIPMENT E. CONDUIT HANGERS FOR EACH CONDUIT BELOW CEILING. M FURNISHED UNDER OTHER TRADES THAT REQUIRE ELECTRICAL CONNECTIONS. INFORM CONTRACTORS OF OTHER TRADES OF THE REQUIRED 1• FOR INDIVIDUAL CONDUIT RUNS NOT DIRECTLY FASTENED TO THE STRUCTURE, USE ROD HANGERS MANUFACTURED BY CADDY, ACCESS TO AND CLEARANCES AROUND ELECTRICAL EQUIPMENT TO MAINTAIN SERVICE ABILITY AND CODE COMPLIANCE. UNISTRUT OR POWERSTRUT. FOR MULTIPLE CONDUIT RUNS, USE UNISTRUT OR POWERSTRUT TRAPEZE TYPE CONDUIT SUPPORT rn B. VERIFY EQUIPMENT DIMENSIONS AND REQUIREMENTS WITH PROVISIONS SPECIFIED UNDER THIS SECTION. CHECK ACTUAL JOB CONDITIONS DESIGNED FOR MAXIMUM DEFLECTION NOT GREATER THAN 1/8". 4 BEFORE FABRICATING WORK. REPORT NECESSARY CHANGES IN TIME TO PREVENT NEEDLESS WORK. CHANGES OR ADDITIONS, SUBJECT TO j ADDITIONAL COMPENSATION, WHICH ARE MADE WITHOUT WRITTEN AUTHORIZATION AND AN AGREED PRICE, SHALL BE AT THE CONTRACTOR'S Cn RISK AND EXPENSE. 0 1.11 CUTTING AND PATCHING A. ALL CUTTING AND PATCHING REQUIRED FOR WORK OF THIS DIVISION IS INCLUDED HEREIN. COORDINATION WITH GENERAL CONTRACTOR Project Number V) AND OTHER TRADES IS IMPERATIVE. CONTRACTOR SHALL BEAR THE RESPONSIBILITY FOR AND THE ADDED EXPENSE OF ADJUSTING FOR SPA16002.0 V) IMPROPER HOLES, SUPPORTS, ETC. 1.12 ACCEPTANCE AND DEMONSTRATION N A. UPON COMPLETION OF THE WORK, AT A TIME TO BE DESIGNATED BY THE OWNER, THE CONTRACTOR SHALL DEMONSTRATE FOR THE Sheet Name it OWNER THE OPERATION OF THE ELECTRICAL INSTALLATION, INCLUDING ANY AND ALL SPECIAL ITEMS INSTALLED BY HIM OR INSTALLED o UNDER HIS SUPERVISION. C B. PROPERLY SET LIGHTING CONTROL PANELS, AUTOMATIC TIME SWITCHES, ETC. TO PERFORM SWITCHING OPERATIONS IN ACCORDANCE WITH SPECIFICATIONS SCHEDULES PROVIDED BY THE OWNER'S REPRESENTATIVE, AND DEMONSTRATE (USING THE MANUFACTURER'S OPERATING INSTRUCTIONS) HOW 0 TO OVERRIDE CONTROLS AND/OR TEST TIME SWITCHES PROGRAMMING. a a w 1 ELECTRICAL SPECIFICATIONS SCALE: N.T.S. Y U Q Sheet Number U U O w G EOm2 i�