|
GREASE INTERCEPTOR CALCULATIONS
<br />FIXTURE TYPE DFU'S QUANTITY TOTAL
<br />FLOOR DRAIN 2 6 12
<br />FLOOR SINKS 4 7 28
<br />MOP SINKS 3 1 3
<br />'TOTAL DRAINAGE FIXTURE UNITS 43
<br />GREASE INTERCEPTOR MINIMUM REQUIRED VOLUME (GYALLONS) 1,250
<br />GREASE INTERCEPTOR SHALL. BE 1,500 GALLONS PER PILOT / FLYING XS DIRECTIVE
<br />1 . BASED ON TABLE 10-3 OFTHE 2013 CALIFORNIA PLUMBING CODE
<br />MATERIAL SCHEDULE
<br />SYSTEM MATERIAL
<br />SAN) TARY WASTE & VENT (ABOVE GRADE) HUBLESS CASTIRON (PVC DWV OPTIONAI
<br />SANITARY WASTE & VENT (BELOW GRADE) SERVICE WEIGHTCAST IRON (PVC DWV OPTIONAL.)
<br />POTABLE WATER (ABOVE GRADE) TYPE L I-IARD-DRAWN COPPER
<br />POTABLE WATER <, 2-1/2" (BELOW GRADE) TYPE L HARD�DRAWN COPPER (BRAZEDJOINTS)
<br />POTABLE WATER ;� 3" (BELOW GRADE) DUCTILE IRON
<br />NATURAL GAS (ABOVE GRADE/ON ROOF) SCHEDULE 40 BLACK STEEL,, PAIN I -ED OSHA YELLOW
<br />NATURAL GAS (BELOW GRADE) APPROVED 'PE" PIPE FOR GAS
<br />COMPRESSED AIR (ABOVE & BELOW GRADE) SCHEDULE 40 BLACK STEEL, AS FM A120
<br />CONDENSATE TYPE L HARD -DRAWN COPPER (P\NV DWV OPTIONAL)
<br />CARBONATED LIQUID WASTE PIPING CPVC, DO NOT USE COPPER OR CAST IRON.
<br />WATER HEATER SCHEDULE
<br />MARK WH -1 WH 2
<br />. ........ .
<br />NATURAL. GAS INPUT (13TWHR) 399,000 399,000
<br />ELECTRICAL 120V 110 / 60Hz 120V / 10 / 60Hz
<br />RECOVERY @ 100'F RISE 464 GPI1 464 GPH
<br />MANUFACTURER HTP HTP
<br />MODEL. PHP -399-119 PHIP-399-119
<br />S FO RAG E CAPAC I TY 119 GAL� 119 GAL�
<br />WEIGHT (DRY) 575 LBS. 575 LBS,
<br />1. PROVIDE #7450P-212 CONDENSATE NEUTRALIZER ON EACH HEATER,
<br />2. PROVIDE 4" TERMINATION VENT KITFOR INLET#V3000 AND OUTLET#V3000,
<br />3, WATER HEATERS FURNISHED BY OWNER. NO SUBSTITUTIONS ALLOWED.
<br />INSTALLATION AND FINAL CONNECTION BY PC.
<br />TESTING PROCEDURES.
<br />TEST INS FALLED WATER PIPING AT 100 PSI FOR A PERIOD OF 8 HOURS,
<br />I OBSERVING FOR ANY VISIBLE LEAKS,TEST PIPING AGAIN WITH
<br />FIXTURES INSTALLED,
<br />CHLORINATE ALL. WATER PIPING , FOR A PERIOD OF 8 FIRS, BY CHARGING
<br />WITH A HYPOCHLORINATE SOLUTIONTO ACHIEVE A 5 PPM STRENGTH
<br />AT THE FIXTURE FURTHES F FROM THE POINTOF APPLICATION, UPON
<br />2 COMPLETION OF THE CHLORINATION, FLUSH AL.L. PIPING UNTIL NO
<br />CHLORINE CAN BE DETECTED BY TASTE, CLEAN ALL STRAINERS AND
<br />SET WATER FLOWS FROM FIXTURES IN ACCORDANCE WITH
<br />MANUFACTURER AND LOCAL REQUIREMENTS.
<br />3 TEST INSTALLED GAS PIPING AT- 60 PSI FOR A PERIOD OF 2 FIRS, USING
<br />SOAP AND WATER OBSERVING FOR ANY VISIBLE LEAKS ATALLJOINTS.
<br />TES FINSTALLED WASTE AND VENT PIPING FOR A PERIOD OF 8 HRS, BY
<br />4 CAPPING OR PLUGGING ALLJOINTS -TO A LEVEL OF THE HIGHEST
<br />FIXTURE OR FITTING. FILLTHE SYSTEM WITH WATER AND OBSERVE
<br />FOR ANY LEAKS.
<br />SUPPLIER'S MATERIAL PACKAGE
<br />PILOT/ FLYING J PARTICIPATES IN A NATIONAL ACCOUNTS PROGRAM WITH
<br />HAINES, JONES, AND CADBURY OF BENTONVILLE, ARIZONA. CONTACT- -THE
<br />ACCOUNT REPRESENTATIVE FOR PRICING AND EQUIPMENTINCLUDED INTHE
<br />PACKAGE,
<br />PHONE NUMBER- (800) 459-7099
<br />EMAIL: PILOT@HJCINC,COM
<br />NO OTHER MANUFACTURERS OR SUPPLIERS WILL BE ACCEPTED.
<br />EQUIPMENTPACKAGE�
<br />ALL PLUMBING FIXTURES, CHINA, FAUCETS, SUPPLIES, AND PUMPS ON THE
<br />PLANS AND SPEC I FICAT IONS.
<br />IN FLOOR PACKAGE:
<br />';�:Tl F�[,.o�D—RT)-F�Ai—N'3—,'Fl.,()OR SINKS, AND CLEANOUT AS SPECIFIED ON THE PLANS
<br />AND SPECIFICATIONS.
<br />EN FIRE SHEET HAS BEEN UPDATED -TO MATCH
<br />CURRENT PILOT/ FLYING J -TRAVEL CENTER DESIGN
<br />CRITERIA AND ARCHITECTURAL BASE
<br />PLUMBING FIXTURE SCHEDULE
<br />GENERAL PLUMBING NO FES
<br />1 DRAWINGS AIRE DIAGRAMMATIC ONLY AND REPRIESENTTHE GENERAL SCOPE OFTHE
<br />WORK, PRIOR -TO SUBMITTING BID, VISIT THE JOB SITE TO OBSERVETHE EXISTING
<br />CONDITIONS OFTHE PROJECT. REVIEW THE GENERAL NOTES, SPECIFICATIONS AND PLANS
<br />FOR ADDITIONAL REQUIREMENTS THAT MAYNOT BE SPECIFICALLY CALLED OUT INTHIS
<br />PORTION OF TH E CONS TRUCTION DOC UM ENTS. NOTIFY ARCHITECT OF ANY CONFLICTS OR
<br />DISCREPANCIES PRIOR TO, SUBMISSION OF BID.
<br />2, INSTALLATION SHALL COMPLY WITH LEGALLY CONSTITUTED CODES AND THE
<br />REQUIREMENTS OF AUTHORITIES HAVING JURISDIC FION AND ALSO MEE1' ALL
<br />REQUIREMENTSOFTHE LANDLORD, OBTAIN A COPY OFTHE LANDLORD'S REQUIREMENTS
<br />AND REVIEW PRIOR"TO SUBMITTING BID,
<br />3� PROVIDE A CONSTRUCTION RECORD SETOF "AS -BUILT" DOCUMENTS TO THE ARCHITECT'
<br />REFLEC TING ANY VARIANCES OF INSTALLED PIPING LOCA-1-10NS OR EQUIPMEN ['CONTRARY
<br />TO THE CONSTRUC TION DOCUMENTS, REFERTO SPECIFICATIONS.
<br />4, PROVIDE TO THE ARCHITECT A COPY OF INSPECTION REPORT'S AND APPROVAL
<br />CERTIFICATES FROM LOCAL AND STATE INSPECTIONS, REFER 1-0 SPECIFICATIONS,
<br />5, PLANS AND SPECIFICATIONS GOVERN WHERE THEY EXCEED CODE REQUIREMENTS,
<br />6. COMPLY WITH HEALTH DEPARTMENT REGULATIONS, PROVIDE CLEARANCE FOR CLEANING
<br />BEHIND AND UNDER EXPOSED PIPING AS REQUIRED BY HEALTH DEPARTMENT, CONFORM
<br />TO HEALTH DEPARTMENT REQUIREMENTS FOR LOCATIONS OF FLOOR SINKS,
<br />7, PROVIDE ITEMS AND WORK AS REQUIRE[) FOR A COMPLETE AND WORKING PLUMBING
<br />INS FALLATION FOR EACH PIECE OF KITCHEN EQUIPMENT, PROVIDE ROUGH -INS AND
<br />CONNECT' TO THE KITCHEN EQUIPMENT WITH TRAPS, SUPPLIES, SHUTOFF VALVES, PIPES -TO
<br />THE WALL, ESCUTCIIEONS, ETC AS SHOWN, SPECIFIED AND REQUIRED,
<br />8 VERIFY LOCATION AND DEPTH OF UTILITIES AT POINTS OF CONNECTION BEFORE START OF
<br />PIPING INSTALLATION,
<br />9, DO NOT SCALE FLOOR F'LANS FOR EXACTHORIZONTAL LOCA"rION OF PIPE ROUTING.
<br />10� REFER TO ARCHITECTURAL PLANS FOR EXACTLOCATION AND MOUNTING HEIGH fS OF
<br />PLUMBING FIXTURES,
<br />11, COORDINATE ALL WASTE, VENF, WATER, GAS, CONDENSATE,AND STORM PIPING -TO AVOID
<br />CONFLICT WITH OTHERFRADES AND CONTRACTORS. DO NOT INSTAL,[., PIPING OVER
<br />ELECTRICAL PANELS. COORDINATE PIPING INSTALLATION WITH STRUCTURAL GRADE BEAMS,
<br />FOOTINGS, COLUMN PIERS, ETC, SLEEVE F1 IPI NGTH ROL)GH GRADE BEAMS, FOOTING, ETC,
<br />WHERE REQUIRED AND AS NOTED ON PLANS. COORDINATE SLEEVE INSTALLATIONS WITH
<br />THE ARCHITECT, STRUCTURAL ENGINEER, STRUCTURAL CONTRACTOR AND GENERAL
<br />CONTRACTOR BEFORE CONCREFE IS INSTALLED.
<br />12. COORDINATE ALL ROOF PENETRATIONS WITH OTHER TRADES, MAINTAIN 10'MINIMUM
<br />CLEARANCE FROM ALL AIR INTAKES, MAINTAIN 2'-0" OF CLEARANCE FROM ALL OTHER
<br />EQUIPMENT.
<br />13. COORDINAT-E FLOOR DRAIN LOCATIONS WITH THE ARCHITECTURAL PLANS, INSTALL RIM OF
<br />FLOOR DRAINS AND FLOOR SINKS BELOW FINISHED FLOOR LEVEL,
<br />14� INS FALL CONCEALED PIPING -FIGHT TO THE STRUCTURE AND AS HIGH AS POSSIBLE, INSTALL
<br />EXPOSED PIPINGTIGH-r To THE STRUCTURE, WALL OR CEILING AND AS HIGH AS POSSIBLE,
<br />COORDINATE WITH OTHER TRADES DD AVOID CONFLICTS,
<br />15� PAINT ALL EXPOSED GAS AND WATER PIPING USING RUST INHIBITOR PAINT, PAINTAND
<br />COLOR SHALL BE COORDINATED WITH THE ARCHITECT AND / OR OWNER,
<br />16, INSULATE ALL DOMESTIC WATER AND STORM DRAIN PIPING PER SECTION 15250 OF
<br />SPEC I FICATIONS.
<br />1T SEAL ALL PEN ETRATIONSTH ROUGH FLOORS, WALLS, CEILINGS AND ROOFS. REPAIR
<br />SURFACES TO MATCH ADJACEN FAREAS.
<br />1& INSTALL NO PLUMBING ROOF PENETRATIONS JHROUGH GREASE FILTER PANS ON THE
<br />ROOF, REFER TO MECHANICAL DRAWINGS PRIOR TO STARFOF INS TALLATION.
<br />19 PROVIDE WALL- BACKING OR SPECIFIED CARRIERS FORTHE PROPER SUPPORT OF
<br />INSTALLED WAL.L. HUNG FIXTURES AND EQUIPMENT,
<br />20, CLEAN INSTALLED PLUMBING FIXTURES AND EQUIPMENT,
<br />21, SEAL AROUND INSTALLED FIXTURES AND KITCHEN EQUIPMENTWFT'H CAULK,
<br />22, WHERE "FLEX" TUBING IS CALLED FOR, PROVIDE A FOUR FOOT COILED LENGTH OF TYPE
<br />"K" SOFT COPPER -TUBING FROM WATER SHUT -OF -F VALVE TOTHE EQUIPMENT CONNECTION
<br />OF SAME SIZE AS CONNEc rFON TO KITCI,-IEN EQUIPMEN f WITH 114" BEING MINIMUM SIZE.
<br />PROVIDE CONNEc rORS AND ADAPTERS AS REQIJIRED,
<br />21 PROVIDE INDIRECT WASTE LINES OF SAME SIZE AS CONNECTION TO EQUIPMEN IF WITH
<br />3/4" BEING MINIMUM SIZE, ROUTE FROM EQUIPMENT CONNECTION POINTS INDICATEDTO
<br />FLOOR DRAIN OR FLOOR SINK, PROVIDE AIR GAP OF TWO PIPE DIAMETERS MINIMUM PER
<br />CODE�
<br />24. PROVIDE FRAP PRIMERS WFIERE REQUIRED BY LOCAL AUTHORITIES
<br />25. VALVES SHALL BE LINE SIZE LJNLESS OTHERWISE NOTED.
<br />26. PROVIDE VERTICAL LIFT SPRING LOADED CHECK VALVES IN HOTAND COLD WATER
<br />SUPPLIES FOR 3-COMPAR-TMENT SINKS, PRE -RINSE UNITS, ANDJANrrOR SINKS
<br />DOWNSTREAM OF SHuFOFF VALVES,
<br />2T WATER HAMMER ARRESTORS SHALL BE SIZE "B" UNLESS NO FED OTHERWISE,
<br />28, ASSUMED MINIMUM 55 PSI SERVICE PRESS FOR DOMESTIC WATER SIZING.
<br />29, SEE WASTE AND VENT ISOMETRIC ON SHEET P4 FOR' VENT ROUTING AND SIZING,
<br />30. CARBONATED LIQUID WAS1 E PIPING SHALL BE OF CORROSIVE RESISTIVE MATERIAL. DO NOT
<br />USE COPPER OR CAST IRON LINTIL. PROPER NEUTRALIZATION OR DILUTION HAS OCCURRED,
<br />(CPC SECT10,N 811),
<br />ABBREVIATIONS
<br />ABB�
<br />ics
<br />3CS
<br />AFF
<br />BC
<br />BFP
<br />CID
<br />EX
<br />FCO
<br />FID
<br />FS
<br />F -W
<br />G
<br />GW
<br />KEC
<br />LAV
<br />MAX
<br />DEFINITION
<br />ONE COMPAR FMENT SINK
<br />THREE COMPARTMENTSINK
<br />ABOVE FINISHED FLOOR
<br />BEVERAGE CONDUIT
<br />BACKIFLOW PREVENTOR
<br />CONDENSATE DRAIN
<br />EXISTING
<br />FLOOR CLEANOUT
<br />FLOOR DRAIN
<br />FLOOR SINK
<br />FILTERED WATER
<br />GAS
<br />GREASE WASTE
<br />KITCHEN EQUIPMENT CONTRACTOR
<br />LAVATORY
<br />MAXIMUM
<br />ABB,
<br />MBH
<br />MIN
<br />Ms
<br />NTS
<br />PC
<br />TMV
<br />Tp
<br />Typ
<br />UR
<br />V
<br />W
<br />W/
<br />W/O
<br />WC
<br />WCO
<br />WI -I
<br />DEFINIFION
<br />1000 B_FH PER HOUR
<br />MINIMUM
<br />MOP SINK
<br />NOTTO SCALE
<br />PLUMBING CONTRACTOR
<br />THERMOSTATIC MIXING VALVE
<br />TRAP PRIMER
<br />TYPICAL
<br />URINAL
<br />VENT
<br />WASTE
<br />WITH
<br />WITHOU T'
<br />WATER CLOSET
<br />WALL CLEANOUT
<br />WATER HEATER
<br />PLUMBING SYMBOL LEGEND
<br />COLD WATER
<br />UNDERSLAB GOLD WATER
<br />Po
<br />CONNECTIONS
<br />11 o, i-IoT wA TER
<br />1011
<br />MARK
<br />DESCRIPTION
<br />MANUFACFURER
<br />MODEL
<br />FIL rERED WATER
<br />W
<br />SANITARY WASTE
<br />-GW---
<br />REMARKS
<br />VENT'
<br />--G----
<br />NAT URAL GAS PIPING
<br />WASTE
<br />VENT
<br />CW
<br />HW
<br />Gs--
<br />AG -A
<br />CO--
<br />ELBOW UP
<br />P1 1
<br />SEE
<br />TEE Ul"'
<br />P3,2
<br />BALI VALVE
<br />
<br />AIR GAP FIT FING
<br />ZURN
<br />AG -5
<br />PLANS/
<br />MIXING VALVE
<br />F`5� 1
<br />BALANCING VALVE
<br />AIR GAP ADAPTER
<br />AG -B
<br />PRESSURE GAUGE --
<br />P5�2
<br />DETAILS
<br />STRAINER
<br />P6,1
<br />BACKFLOW PREVENTOR
<br />BFP-1
<br />RECIRCULATION PUMP
<br />375L.
<br />03-------
<br />FLOOR DRAIN
<br />2-1/2"
<br />FLOOR SINK
<br />LEAD-FREE REDUCED PRESSURE PRINCIPLE ASSEMBLY,
<br />FRENCH DRAIN
<br />P7
<br />WASHING MACHINE BOX
<br />CO -1 0-----
<br />FLOOR CLEANOUT
<br />CO -2
<br />WALL CLEANOUT
<br />LESS SHUT-OFF'VALVES, SEE DETAIL VP61
<br />BFP2
<br />ROOF DRAIN
<br />375 -ST
<br />GAS ELBOW
<br />GAS TEE
<br />LEAD-FREE STAINLESS STEEL REDUCED PRESSURE
<br />PRESSURE REGULATOR
<br />BACKIFLOW
<br />SOLENOID VALVE
<br />GASTEST FEE
<br />cx--)
<br />BAC KFLOW PREVEN TOR, SEE DE I AlL 1/ P6.2
<br />- -------
<br />EQUIPMENT JAG (RESTAURANT-)
<br />ZUR.N
<br />KEYED NOTE
<br />Q5
<br />CONNECT -FO EXISTING
<br />. . I . -'-_
<br />BFP-3
<br />PREVENTOR
<br />375 -XL.
<br />LINE
<br />LEAD-FIREE REDUCED PRESSURE BACKFLOW
<br />SIZED
<br />PREVENTOR, SEE DE FAIL- 6/P61
<br />BFP4
<br />740
<br />3/8"
<br />CARBONATED BEVERAGE BACKFLOW PREVENTOR WITH
<br />VENT,
<br />CO -1.
<br />FLOOR CLEANOUT
<br />ZURN
<br />ZB1400-T-VP
<br />LINE
<br />ADJUSTABLE LEVELING, CAST-IRON BODY, HEAVYDUT`Y
<br />SIZED
<br />SQUARE TOP, VANDAL-J-DROOF SCREWS,
<br />CO -2
<br />WALL, CLEANOUT
<br />ZURN
<br />.. .
<br />ZAB-1468-VP
<br />. .. . . . ................ . . .
<br />LINE
<br />.
<br />BRONZE PLUG WITH ROUND POLISHEL.) BRONZE COVER,
<br />SIZED
<br />VANDAL -PROOF SCREWS,
<br />C.0-3
<br />EXTERIOR CLEANOUT
<br />ZURN
<br />Z1400-vp
<br />LINE
<br />ADJUSTABLE LEVELING, CAST-IRON BODY,
<br />SIZED
<br />VANDAL-FIROOF SCREWS.
<br />ETA
<br />EXPANSION -TANK
<br />AMTROL
<br />ST- 12
<br />3/4"
<br />4A GALLONS. SEE DETAIL 2/P6.1, NOWASME.
<br />. . .. . ...... .
<br />COMBINATION EYE -WASH / FAUCET/ DRENCH HOSE,
<br />EW -1
<br />EYE -WASH
<br />SPEAKMAN
<br />SEF -9000
<br />.1 /2"
<br />1/2"
<br />PROVIDE SPEAKMAN SEF -TW MIXING VALVE, MAX FEMP
<br />SETTING� 80'F.
<br />CAST-IRON BODY W/ POLISHED NICKEL BRONZE SQUARE
<br />FD --1
<br />ZB-415-5S-3NI-
<br />LFGHT-DUTY ADJUSTABLE LEVELING STRAINER,
<br />VANDAL PROOF SCREWS, PROVIDE W/ PROSET SYSTEMS
<br />TRAP GUARD,
<br />FLOOR DRAIN
<br />ZURN
<br />3"
<br />1- 1/2"
<br />ADJUSTABLE LEVELING CAST-IRON BODY W/ POLISHED
<br />FD -2
<br />ZN-4157E-3NI_,
<br />NICKEL, BRONZE ROUND STRAINER W/ 4"0 FUNNEL,
<br />VANDAL -PROOF SCREWS, PROVIDE W/ PROSE -F SYSTEMS
<br />TRAP GUARD.
<br />FD 3
<br />f-D-2340-PV3-Y
<br />ADJUSTABLE, PVC BODY, CAS FIRON GRATE. PROVIDE W/
<br />PROSET SYSTEMS -TRAP GUARD.
<br />14"x`14"x5" PVC' BODY, PROVIDE W/ HALF -GRATE, PROVIDE
<br />FS -1
<br />FD-2370-PV3
<br />31,
<br />1-1/2"
<br />TRAP PRIMER (TP, -1) AND CONNECTION IF: REQUIRED BY
<br />LOCAL C'ODE, PLUG TRAP PRIMER CONNECTION IF NO F
<br />FLOOR SINK
<br />ZURN
<br />U S ED.
<br />14"x14"xV PVC BODY, NO GRATE, PROVIDE TRAP PRIMER
<br />FS 2
<br />FD-23'70-PV3
<br />3"
<br />1-1/2"
<br />(TIP -1) AND CONNECTION IF REQUIRED BY LOCAL CODE,
<br />PLUG TRAP PRIMER CONNECTION IF NOTUSED,
<br />SHALL BE EQUAL -TO BARGER AND SONS PRE -CAST.
<br />GI1�
<br />GREASE INTERCEPTOR
<br />6ll
<br />3''
<br />INTERCEPTOR SHALL BE 1,500 GALLONS, SEE DETAIL
<br />12/P6.1
<br />HB -1
<br />HOSE BIBB
<br />ZURN
<br />Z-1 321
<br />3/4"
<br />L.00SE.-KEY NON -FREEZE FOR 4" WALL THICKNESS,
<br />PROVIDED WITH APPROVED VACUUM BREAKER.
<br />BOWL' PROVIDED BY COUNTERTOP SUPPLIER AS PART
<br />OF COUNTER fOF1,
<br />FAUCET, MOEN #8884, SINGLE HANDLE ADA METERING
<br />L-1
<br />LAVATORY
<br />MOEN
<br />8414BN
<br />1-1/2"
<br />1-1/2"
<br />1/2"
<br />V2"
<br />FAUCET (SETFOR 0,20 gpc (0,76 LICYCLE) @ 24
<br />SECONDS), CHROME FINISH, OPEN GRID STRAINER W1
<br />TAILPIECE, WHEEL HANDLE STOPS, 12"BRAIDED
<br />STAINLESS STEEL. SUPPLY RISERS, CAST BRASS P -TRAP
<br />WITH C/O PLUG, ADA COMBINATION -TRAP & SUPPLY
<br />WRAP KIT, PROVIDE W/ MOEN #99550 4" DECK PLATE
<br />MS -1
<br />MOP SINK
<br />FIAT
<br />MSB -3624
<br />3"
<br />-1 /2"
<br />1/2"
<br />1/2''
<br />36"x24"x10" W/ SHELF, APPROVED VACUUM BREAI�E�,
<br />LOOSE -KEY STOPS, PAIL HOOK, RUBBER HOSE.
<br />LEAD-FREE THERMOSTATIC MIXING VALVE, DIAL
<br />MV -1
<br />S59 -2080 -T -B -P
<br />1-1/4"
<br />THERMOMETER, WALL MOUNTING BRACKET, PIPED
<br />MIXING VALVE
<br />BRADLEY
<br />ASSEMBLY WITH INLET AND OUTLET SHU FOFF
<br />MV
<br />S59 -4000-A-
<br />'314"
<br />LEAD-FREE THERMOSTATIC MIXING VALVE W/ 3/8"
<br />-2
<br />S45-2456
<br />3/4"
<br />COMPRESSION FITTINGS, 0.5 GPM MIN. FLOW.
<br />460V, 30,6OHz, 3HP. DISCARD TANK, PROVIDED WITH
<br />P-1
<br />BOOSTER PUMP
<br />HYFAB
<br />eMVPjr-3H43
<br />2l'
<br />PUMP AND INSTALL GOULDS HYDROPRO V250
<br />DIAPHRAGM TANK
<br />P-2
<br />CONDENSATE--- PUMP
<br />LITTLE GIANT
<br />VCC-20UL-S
<br />3/8"
<br />115 VOLTS. ROUTE CONDENSATE DISCHARGETO AIR GAP
<br />(#554200)
<br />FFFTING IN CASHIER DESK FIANDSINK VENT LINE.
<br />P RV -1
<br />P R ESS U R R E D U C I N G
<br />ZURN
<br />500XLYSBR
<br />2- /2"
<br />PRESSURE REDUCING VALVE W/ INTEGRAL. BY-PASS
<br />VALVE
<br />CHECK VALVE AND STRAINER
<br />R1.1-1
<br />ROOF DRAIN
<br />ZURN
<br />7A -100 -EA DP
<br />4"
<br />15"0 CAST IRON BODY W/ ALUMINUM DOME, DECK PLATE
<br />RP -1
<br />RECIRCULATION PUMP
<br />GRUNDFOS
<br />ALP HA -1 555SF
<br />3/4"
<br />120V,,10, 601-1z, 1/25 HP, 4GPM, 14FT'OF HEAD, OPERATING
<br />LC
<br />IN AU_FO-ADAPTMODE,
<br />CAST-IRON BODY W/ POLISHED BRONZE SQUARE
<br />SD_i
<br />SHOWER DRAIN
<br />ZURN INDUSTRIES
<br />ZB-415--5S-2NL
<br />2''
<br />1-1/2"
<br />LIGHT-DUTY ADJUSTABLE LEVELING STRAINER,
<br />VANDAL -PROOF SCREWS, PROVIDE W/ PROSET SYSTEMS
<br />TRAP GUARD,
<br />. . ...... . ..
<br />HYDRAPIPE AND ARM, DIVERTER VALVE AND HAND-HEL.D
<br />SHOWER FOR ADA ACCESS -
<br />SH -1
<br />SHOWER ASSEMBLY
<br />SYMMONS
<br />1-801SA58-FSB
<br />2"
<br />1-1/2"
<br />1/2''
<br />SHOWER HEAD: SPEAKMAN S. -3010 -BN -E2 (2.OGPM), 5-JEA
<br />HEAD W1 SWIVEL BALL CONNECTOR, QUICK DISCONNECT
<br />TO BE MOUNTED AT HOSE TO BASE CONNECTION POINT.
<br />ST -1
<br />HAMMER ARRESTOR
<br />SIOUX CHIEF
<br />653 -BS
<br />:3/4"
<br />3/4" MIP THREADED CONNECTION,
<br />SV -_1
<br />AIR ADMITTANCE
<br />STUDOR
<br />20301
<br />2"
<br />2" PVC AIR ADMITTANCE VALVE, LOCATE 4" MIN. ABOVE
<br />VALVE
<br />THE WEIR OF TRAP BEING SERVED,
<br />TD -1
<br />FRENCH DRAIN
<br />ZURN
<br />Z8605 -RPG
<br />4"
<br />2"
<br />'TRENCH DRAIN W/ 4" NO -HUB END OUTLET, REINFORCED
<br />GALVANIZED PERFORATED GRATE CLASS B
<br />AUTOMATICTRAP PRIMER VALVE, INSTALL AT A MINIMUM
<br />TRAP PRIMER
<br />SIOUX CHIEF
<br />695-01
<br />OF 6" ABOVE THE GRID / FLOOD RIM OF THE FIXTURE(S)
<br />BEING SERVED.
<br />UR -1
<br />WALL MOUNT ED URINAL WITH TOTOTEU1 LN 12#CP FLUSH
<br />VALVE (SET FOR 0,125 GPF) AND VACUUM BREAKER.
<br />URINAL
<br />ZURN
<br />Z5755. -U
<br />2ll
<br />1-1/2"
<br />3/4"
<br />WALL MOUNTED URINAL WITH TOTO TEU1 LN1 2#CP FLUSH
<br />UR -2
<br />VALVE (SET FOR 0.125 GF`F) AND VACUUM BREAKER
<br />MOUNTED AT ADA HEIGHT,
<br />WB_ -i
<br />WASHER BOX
<br />GUY -GRAY
<br />WB -200
<br />2"
<br />1-1/2"
<br />1/2"
<br />1/2"
<br />1/4 TURN VALVES WITH 1/2" MIP / SWEAT CONNECTION, 2'l
<br />THREADED DRAIN.
<br />BOWL: ELONGATED, FLOOR MOUNTED, VITREOUS
<br />CHINA, PROVIDE WITH APPROVED BACKFLOW
<br />PREVENTION DEVICE OR METHOD. PROVIDE JONES
<br />G13-002, CO2 993 CLOSET BOLF/WAX RING KIT
<br />VALVE: IN REST ROOMS SHIAL L BETOTO TETI L.N32#C P
<br />WC__1
<br />CT705EN
<br />BATT ERY POWERED1.28 GPF ADA COMPLIANT, IN
<br />SHOWERS SHALL BE_FOFO'T"MT1L,N-32#CP MANUAL 1.28
<br />GPF ADA COMPLIANT
<br />SEAT, CHURCH 3155SSC OPEN FRONT SEAT W/ SELF
<br />SUSTAINING CHECK HINGES, STA-TITE FASTENING
<br />SYSTEM
<br />WATER CLOSET
<br />TOTO
<br />4ll
<br />2''
<br />BOWL - ADA HEIGHT, ELONGATED, FLOOR MOUNTED,
<br />VITREOUS CHINA, PROVIDE WITH APPROVED BACKFLOW
<br />PREVENTION DEVICE OR METHOD. PROVIDEJONES
<br />G1 3-002, CO2 -993 CLOSET BOLT/WAX RI NG KI T.
<br />VALVE: IN RES FIROOMS SHALL BE TOTO FETI LN32#CP
<br />WC -2
<br />CT705ELN
<br />BAFTERY POWERED 1.28 GPF ADA COMPLIANT, IN
<br />SHOWERS SHALL BE To'TO TM rl LN 324CP MANUAL 1.28
<br />GPF ADA COMPLIAN F
<br />SEAT� CHURCH 3155SSC OPEN FRONT SEATW/ SELF
<br />SUSTAINING CHECK HINGES,sTA-TITE FASTENING
<br />SYSTEM
<br />METER FOR COLD WATER APPLICATION, INS FALL PER
<br />WM-1
<br />WATER METER
<br />BADGER METER
<br />380CS
<br />2"
<br />MANUFACTURER'S SPECIFICATIONS AND CLEARANCES,
<br />SEE DETAIL 5/P6 2
<br />GENERAL PLUMBING NO FES
<br />1 DRAWINGS AIRE DIAGRAMMATIC ONLY AND REPRIESENTTHE GENERAL SCOPE OFTHE
<br />WORK, PRIOR -TO SUBMITTING BID, VISIT THE JOB SITE TO OBSERVETHE EXISTING
<br />CONDITIONS OFTHE PROJECT. REVIEW THE GENERAL NOTES, SPECIFICATIONS AND PLANS
<br />FOR ADDITIONAL REQUIREMENTS THAT MAYNOT BE SPECIFICALLY CALLED OUT INTHIS
<br />PORTION OF TH E CONS TRUCTION DOC UM ENTS. NOTIFY ARCHITECT OF ANY CONFLICTS OR
<br />DISCREPANCIES PRIOR TO, SUBMISSION OF BID.
<br />2, INSTALLATION SHALL COMPLY WITH LEGALLY CONSTITUTED CODES AND THE
<br />REQUIREMENTS OF AUTHORITIES HAVING JURISDIC FION AND ALSO MEE1' ALL
<br />REQUIREMENTSOFTHE LANDLORD, OBTAIN A COPY OFTHE LANDLORD'S REQUIREMENTS
<br />AND REVIEW PRIOR"TO SUBMITTING BID,
<br />3� PROVIDE A CONSTRUCTION RECORD SETOF "AS -BUILT" DOCUMENTS TO THE ARCHITECT'
<br />REFLEC TING ANY VARIANCES OF INSTALLED PIPING LOCA-1-10NS OR EQUIPMEN ['CONTRARY
<br />TO THE CONSTRUC TION DOCUMENTS, REFERTO SPECIFICATIONS.
<br />4, PROVIDE TO THE ARCHITECT A COPY OF INSPECTION REPORT'S AND APPROVAL
<br />CERTIFICATES FROM LOCAL AND STATE INSPECTIONS, REFER 1-0 SPECIFICATIONS,
<br />5, PLANS AND SPECIFICATIONS GOVERN WHERE THEY EXCEED CODE REQUIREMENTS,
<br />6. COMPLY WITH HEALTH DEPARTMENT REGULATIONS, PROVIDE CLEARANCE FOR CLEANING
<br />BEHIND AND UNDER EXPOSED PIPING AS REQUIRED BY HEALTH DEPARTMENT, CONFORM
<br />TO HEALTH DEPARTMENT REQUIREMENTS FOR LOCATIONS OF FLOOR SINKS,
<br />7, PROVIDE ITEMS AND WORK AS REQUIRE[) FOR A COMPLETE AND WORKING PLUMBING
<br />INS FALLATION FOR EACH PIECE OF KITCHEN EQUIPMENT, PROVIDE ROUGH -INS AND
<br />CONNECT' TO THE KITCHEN EQUIPMENT WITH TRAPS, SUPPLIES, SHUTOFF VALVES, PIPES -TO
<br />THE WALL, ESCUTCIIEONS, ETC AS SHOWN, SPECIFIED AND REQUIRED,
<br />8 VERIFY LOCATION AND DEPTH OF UTILITIES AT POINTS OF CONNECTION BEFORE START OF
<br />PIPING INSTALLATION,
<br />9, DO NOT SCALE FLOOR F'LANS FOR EXACTHORIZONTAL LOCA"rION OF PIPE ROUTING.
<br />10� REFER TO ARCHITECTURAL PLANS FOR EXACTLOCATION AND MOUNTING HEIGH fS OF
<br />PLUMBING FIXTURES,
<br />11, COORDINATE ALL WASTE, VENF, WATER, GAS, CONDENSATE,AND STORM PIPING -TO AVOID
<br />CONFLICT WITH OTHERFRADES AND CONTRACTORS. DO NOT INSTAL,[., PIPING OVER
<br />ELECTRICAL PANELS. COORDINATE PIPING INSTALLATION WITH STRUCTURAL GRADE BEAMS,
<br />FOOTINGS, COLUMN PIERS, ETC, SLEEVE F1 IPI NGTH ROL)GH GRADE BEAMS, FOOTING, ETC,
<br />WHERE REQUIRED AND AS NOTED ON PLANS. COORDINATE SLEEVE INSTALLATIONS WITH
<br />THE ARCHITECT, STRUCTURAL ENGINEER, STRUCTURAL CONTRACTOR AND GENERAL
<br />CONTRACTOR BEFORE CONCREFE IS INSTALLED.
<br />12. COORDINATE ALL ROOF PENETRATIONS WITH OTHER TRADES, MAINTAIN 10'MINIMUM
<br />CLEARANCE FROM ALL AIR INTAKES, MAINTAIN 2'-0" OF CLEARANCE FROM ALL OTHER
<br />EQUIPMENT.
<br />13. COORDINAT-E FLOOR DRAIN LOCATIONS WITH THE ARCHITECTURAL PLANS, INSTALL RIM OF
<br />FLOOR DRAINS AND FLOOR SINKS BELOW FINISHED FLOOR LEVEL,
<br />14� INS FALL CONCEALED PIPING -FIGHT TO THE STRUCTURE AND AS HIGH AS POSSIBLE, INSTALL
<br />EXPOSED PIPINGTIGH-r To THE STRUCTURE, WALL OR CEILING AND AS HIGH AS POSSIBLE,
<br />COORDINATE WITH OTHER TRADES DD AVOID CONFLICTS,
<br />15� PAINT ALL EXPOSED GAS AND WATER PIPING USING RUST INHIBITOR PAINT, PAINTAND
<br />COLOR SHALL BE COORDINATED WITH THE ARCHITECT AND / OR OWNER,
<br />16, INSULATE ALL DOMESTIC WATER AND STORM DRAIN PIPING PER SECTION 15250 OF
<br />SPEC I FICATIONS.
<br />1T SEAL ALL PEN ETRATIONSTH ROUGH FLOORS, WALLS, CEILINGS AND ROOFS. REPAIR
<br />SURFACES TO MATCH ADJACEN FAREAS.
<br />1& INSTALL NO PLUMBING ROOF PENETRATIONS JHROUGH GREASE FILTER PANS ON THE
<br />ROOF, REFER TO MECHANICAL DRAWINGS PRIOR TO STARFOF INS TALLATION.
<br />19 PROVIDE WALL- BACKING OR SPECIFIED CARRIERS FORTHE PROPER SUPPORT OF
<br />INSTALLED WAL.L. HUNG FIXTURES AND EQUIPMENT,
<br />20, CLEAN INSTALLED PLUMBING FIXTURES AND EQUIPMENT,
<br />21, SEAL AROUND INSTALLED FIXTURES AND KITCHEN EQUIPMENTWFT'H CAULK,
<br />22, WHERE "FLEX" TUBING IS CALLED FOR, PROVIDE A FOUR FOOT COILED LENGTH OF TYPE
<br />"K" SOFT COPPER -TUBING FROM WATER SHUT -OF -F VALVE TOTHE EQUIPMENT CONNECTION
<br />OF SAME SIZE AS CONNEc rFON TO KITCI,-IEN EQUIPMEN f WITH 114" BEING MINIMUM SIZE.
<br />PROVIDE CONNEc rORS AND ADAPTERS AS REQIJIRED,
<br />21 PROVIDE INDIRECT WASTE LINES OF SAME SIZE AS CONNECTION TO EQUIPMEN IF WITH
<br />3/4" BEING MINIMUM SIZE, ROUTE FROM EQUIPMENT CONNECTION POINTS INDICATEDTO
<br />FLOOR DRAIN OR FLOOR SINK, PROVIDE AIR GAP OF TWO PIPE DIAMETERS MINIMUM PER
<br />CODE�
<br />24. PROVIDE FRAP PRIMERS WFIERE REQUIRED BY LOCAL AUTHORITIES
<br />25. VALVES SHALL BE LINE SIZE LJNLESS OTHERWISE NOTED.
<br />26. PROVIDE VERTICAL LIFT SPRING LOADED CHECK VALVES IN HOTAND COLD WATER
<br />SUPPLIES FOR 3-COMPAR-TMENT SINKS, PRE -RINSE UNITS, ANDJANrrOR SINKS
<br />DOWNSTREAM OF SHuFOFF VALVES,
<br />2T WATER HAMMER ARRESTORS SHALL BE SIZE "B" UNLESS NO FED OTHERWISE,
<br />28, ASSUMED MINIMUM 55 PSI SERVICE PRESS FOR DOMESTIC WATER SIZING.
<br />29, SEE WASTE AND VENT ISOMETRIC ON SHEET P4 FOR' VENT ROUTING AND SIZING,
<br />30. CARBONATED LIQUID WAS1 E PIPING SHALL BE OF CORROSIVE RESISTIVE MATERIAL. DO NOT
<br />USE COPPER OR CAST IRON LINTIL. PROPER NEUTRALIZATION OR DILUTION HAS OCCURRED,
<br />(CPC SECT10,N 811),
<br />ABBREVIATIONS
<br />ABB�
<br />ics
<br />3CS
<br />AFF
<br />BC
<br />BFP
<br />CID
<br />EX
<br />FCO
<br />FID
<br />FS
<br />F -W
<br />G
<br />GW
<br />KEC
<br />LAV
<br />MAX
<br />DEFINITION
<br />ONE COMPAR FMENT SINK
<br />THREE COMPARTMENTSINK
<br />ABOVE FINISHED FLOOR
<br />BEVERAGE CONDUIT
<br />BACKIFLOW PREVENTOR
<br />CONDENSATE DRAIN
<br />EXISTING
<br />FLOOR CLEANOUT
<br />FLOOR DRAIN
<br />FLOOR SINK
<br />FILTERED WATER
<br />GAS
<br />GREASE WASTE
<br />KITCHEN EQUIPMENT CONTRACTOR
<br />LAVATORY
<br />MAXIMUM
<br />ABB,
<br />MBH
<br />MIN
<br />Ms
<br />NTS
<br />PC
<br />TMV
<br />Tp
<br />Typ
<br />UR
<br />V
<br />W
<br />W/
<br />W/O
<br />WC
<br />WCO
<br />WI -I
<br />DEFINIFION
<br />1000 B_FH PER HOUR
<br />MINIMUM
<br />MOP SINK
<br />NOTTO SCALE
<br />PLUMBING CONTRACTOR
<br />THERMOSTATIC MIXING VALVE
<br />TRAP PRIMER
<br />TYPICAL
<br />URINAL
<br />VENT
<br />WASTE
<br />WITH
<br />WITHOU T'
<br />WATER CLOSET
<br />WALL CLEANOUT
<br />WATER HEATER
<br />PLUMBING SYMBOL LEGEND
<br />SHEETINDEX
<br />SHEETS
<br />COLD WATER
<br />UNDERSLAB GOLD WATER
<br />Po
<br />140" HOT WATER
<br />11 o, i-IoT wA TER
<br />1011
<br />UNDERSLAB I I O�' HOT' WATER
<br />HOT WA -1 ER RECI RC 0LATION
<br />1W
<br />FIL rERED WATER
<br />W
<br />SANITARY WASTE
<br />-GW---
<br />GREASE WASTE
<br />VENT'
<br />--G----
<br />NAT URAL GAS PIPING
<br />CONDENSATE PIPING
<br />.--S--
<br />STORM LEADER
<br />Gs--
<br />ELBOW DOWN
<br />CO--
<br />ELBOW UP
<br />P1 1
<br />TEE DOWN
<br />TEE Ul"'
<br />P3,2
<br />BALI VALVE
<br />GATE VALVE
<br />P4
<br />CHECKVALVE
<br />MIXING VALVE
<br />F`5� 1
<br />BALANCING VALVE
<br />HOSE BIBB
<br />PRESSURE GAUGE --
<br />P5�2
<br />UNION
<br />STRAINER
<br />P6,1
<br />BACKFLOW PREVENTOR
<br />RECIRCULATION PUMP
<br />P -TRAP
<br />03-------
<br />FLOOR DRAIN
<br />FLOOR SINK
<br />FRENCH DRAIN
<br />P7
<br />WASHING MACHINE BOX
<br />CO -1 0-----
<br />FLOOR CLEANOUT
<br />CO -2
<br />WALL CLEANOUT
<br />AIR GAP FITTING
<br />10
<br />ROOF DRAIN
<br />GAS ELBOW
<br />GAS TEE
<br />PRESSURE REGULATOR
<br />S
<br />SOLENOID VALVE
<br />GASTEST FEE
<br />cx--)
<br />EQUIPMENT TAG (PILOT)
<br />CED
<br />EQUIPMENT JAG (RESTAURANT-)
<br />0
<br />KEYED NOTE
<br />Q5
<br />CONNECT -FO EXISTING
<br />SHEETINDEX
<br />SHEETS
<br />DESCRIPTIONS
<br />PLUMBING PLAN
<br />Po
<br />LEGENDS arid SCHEDULES
<br />7 75 �71 N G' 77 N----'
<br />1011
<br />-
<br />WAS FIE and VEN T`PI PING
<br />1W
<br />PLUMBING PLAN
<br />P1,2
<br />WAS TE arid VE NT P I PI NO
<br />PLUMBING PLAN
<br />P2.1
<br />SERVICES PIPING
<br />PLUMBING PLAN
<br />P2�2
<br />SERVICES PIPING
<br />PLUMBING PLAN
<br />P1 1
<br />CONDENSATE, GAS, and STORM PIPING
<br />PLUMBING PLAN
<br />P3,2
<br />CONDENSATE, GAS, and STORM PIPING
<br />PLUMBING PLAN
<br />P4
<br />WASTE and VENT ISOMETRIC
<br />PLUMBING PLAN
<br />F`5� 1
<br />EQUIPMENT SCHEDULE
<br />PLUMBING PLAN
<br />P5�2
<br />SCHEDULES & CALCULATIONS
<br />PLUMBING PLAN
<br />P6,1
<br />DETAILS
<br />PLUMBING PLAN
<br />P6.2
<br />DE FAILS
<br />PLUMBING PLAN
<br />P7
<br />FIRE s ropPING DETAILS
<br />10126/16
<br />ptw Flym i
<br />cow"NTA
<br />Tws DRA*"G fs 00"relENTM
<br />NO M (A QM,0SLW OF TIMS MAWW
<br />M K.RWT= EXU" AS UMMY
<br />AuT"mzm ey Pix n,ym i
<br />1W
<br />ptw Flym i
<br />cow"NTA
<br />Tws DRA*"G fs 00"relENTM
<br />NO M (A QM,0SLW OF TIMS MAWW
<br />M K.RWT= EXU" AS UMMY
<br />AuT"mzm ey Pix n,ym i
<br />
|