INSTALL_2021 - Laserfiche WebLink

Home Browse Search

2 HP VARIABLE SPEED TURBINE W/ 105 10 1( 3 GPH ELECTRONIC LEAK DETECTION W/ SIPHON PORT & SECOND 110 0 VACUUM SOURCE MINI HYDROSTATIC SENSOR IN 1 BRINE FACTORY SUPPLIED RESERVOIR 3" PEA GRAVEL MIN. TO a PREVENT LOAD TRANSFER TO TOP OF TANK CONTRACTOR TO INSTALL CLEVIS AND COTTER PIN TANK GAUGE ADAPTER & CAP 207 VEEDER ROOT .1 GPH MAGNOSTRICTIVE 205 204 PROBE TANK LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM SET @ 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 3" D.W. FRP BONDED ENTRY FITTING 12612 & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & PLUG 3" OVER 2" FIBERGLASS 148 14 CROSSOVER CONTAINS VACUUM TUBING ONLY FROM ? FILL SUMP 12 3" INSIDE 4" DOUBLE WALL 148 15 "' FRP SIPHON PIPING (VACUUM 1_� MONITORED) � THICKEN CONCRETE SLAB TO BELOW WHERE SECONDARY CONTAINMENT OF SUMP ENDS. 45 DIA. ACCESS (TYP.). DIMENSION REQUIRED SEE NOTES BELOW 10 MANHOLE VARIES WITH FIELD CONDITIONS. 30" I.D. 18" 1-1/2" MIN. CROWN (TYP.) (NP.) (TYP. ALL OPENINGS) 6" WIDE DETECTABLE 0 UNDERGROUND MARKING TAPE EMPIRE MAGNATEC • • 4 ..A #31-143 (8" MIN. 12" MAX.) 217 2 -IN -1 SENSOR BOX 168 2" BALL VALVE (TYP.) 1 3 SENSOR -NO TANK VACUUM SENSOR ASSEMBLY KIT W/ MOUNTING BRACKET 191 SEAL OFF W/ DRAIN 175 2"x24" FLEX (TYP.) 124 1" FRP BONDED ENTRY FITTING (TYP.) 18 1" POWER & MONITORING CONDUIT (ROBROY THROUGH SUMP ONLY) LOOP VACUUM TUBING TO PRODUCT CROSS CONNECT PIPING AND THEN ROUTED TO VAC SENSOR II II 2" INSIDE 3" FIBERGLASS PIPING TO DISPENSERS (VACUUM MONITORED) 14 148 12612 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING LOOPED BETWEEN FITTINGS & THEN ROUTED TO VAC SENSOR ASSEMBLY (TYP.) 22" MANWAY 48" DOUBLE WALL BRINE FILLED SUMP NOTE: SUMP LIQUID MONITORING SENSOR H ALL PRODUCT, SIPHON & CROSS CONNECTION PIPING SHALL BE (IN SENSOR HOLDER BELOW APEX 0 INSTALLED SUCH THAT ALL PENETRATIONS LEAVE THE TANK SUMP OF TANK AT LOWEST POINT) FROM THE SAME SIDE. SUMP SENSOR SHALL BE INSTALLED ON THE SAME SIDE OF PIPING PENETRATIONS AS SHOWN A: SECTION VIEW - 25K REGULAR - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" 3"x18" FLEX CONNECTOR LOOP VACUUM TUBING TO PRODUCT CROSS -CONNECT PIPING AND THEN ROUTED TO VAC SENSOR VEEDER ROOT .1 GPH MAGNOSTRICTIVE 205 04 THICKEN CONCRETE SLAB TO o FIBERGLASS PROBE TANK LEVEL PROBE W/ TLS CAP TANK SUMP ARE MADE AND BELOW LOWEST PENETRATION CONTAINMENT OF SUMP ENDS. 3 GPH ELECTRONIC LEAK DETECTION & RING. OVERFILL ALARM SET ® 90% (TYP.). DIMENSION REQUIRED ° BETWEEN SUMPS AND SIPHON PIPING PENETRATIONS 40" DIA. ACCESS 104 VARIES WITH FIELD CONDITIONS. CAPACITY. USE 4" FLOAT IN INSTALL KIT I MANHOLE MINI HYDROSTATIC SENSOR IN BRINT�1.- 30" I.D. 3 SENSOR -NO TANK VACUUM SENSOR 1 FACTORY SUPPLIED RESERVOI (TYP.) o OO c ASSEMBLY KIT W/ MOUNTING BRACKET :� 0 UNDERGROUND MARKING o 11 o 2" CAP. DRILL HOLES IN END AN INSTALL/ .A : •° ;.'-3 PEA GRAVELMIN. TO a#31 CHANNEL BONDED TO 143 . ,. PREVENT LOAD TRANSFER §IRAIN GROMMETS FOR TUBING PASS THROUGH 16 11 0 o 3" D.W. FRP BONDED ENTRY FITTING 126 12 TO INSTALL CLEVIS AND COTTER PIN o� — SEAL: & 4"x3" CONCENTRIC REDUCER W/ NK J -BOX (TYP.) 188 o 0 0 LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM TEST PORT & PLUG 0- CAUF�� 205 SET @ 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 2 SENSOR -NO TANK VACUUM LOOP VACUUM TUBING FROM 1 SENSOR ASSEMBLY KIT W/ co 3" OVER 2" FIBERGLASS 148 14 MOUNTING BRACKET Z 124 1" FRP BONDED ENTRY FITTING (TYP.) CROSSOVER CONTAINS VACUUM 0 c1) `2 1 " HOMERUN TO BLDG. TURBINE POWER 1" FRP BONDED ENTRY FITTING TUBING ONLY FROM FILL SUMP 18 (ROBROY THROUGH SUMP ONLY) (Typ.)124 IA NOTE: VACUUM MONITORING SENSOR FOR 87 OCTANE " MONITORING CONDUIT 12 126 FITTING & 4"x3" CONCENTRIC PRODUCT AND CROSSCONNECT PIPING IS MOUNTED IN p Z N wz0-- REDUCER W/ TEST PORT & PLUG (ROBROY THROUGH SUMP ONLY) THE 20,000 GALLON 87 OCTANE TANK'S TURBINE SUMP. 48" DOUBLE WALL BRINE VACUUM MONITORING SENSOR FOR 87 OCTANE SIPHON MONITORED SUMP z 2 0- LINE IS MOUNTED IN THE 10,000 GALLON 87 OCTANE CROSSOVER CONTAINS VACUUM 2"x24" FLEX (TYP.) 175 oL TANK'S TURBINE SUMP. 48" DOUBLE WALL BRINE FILLE�� SITE ADDRESS: ADDRESS B: PLAN VIEW - 25K REGULAR - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" 1 3/8 X 1/4 SSI BUSHING INSTALLED AT FACTORY I� 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING LOOPED BETWEEN FITTINGS & THEN ROUTED TO VAC SENSOR ASSEMBLY (TYP.) 40DISPENSERS 2 INSIDE 3" FIBERGLASS PIPING TO (VACUUM MONITORED) 18 HOME RUN TO BUILDING VAC SENSOR (ROBROY THROUGH SUMP ONLY) 188 J -BOX (TYP.) 175 2"x24" FLEX (TYP.) 124 1" FRP BONDED ENTRY FITTING (TYP.) 18 HOME RUN TO BUILDING. TURBINE POWER (ROBROY THROUGH SUMP ONLY) > 10 2 HP VARIABLE SPEED TURBINE W/ 3 GPH ELECTRONIC LEAK DETECTION 0 W/ SIPHON PORT & SECOND VACUUM SOURCE NOTE: THE LAST 2 FEET (MINIMUM) OF CONDUITS THAT ENTER THE DOUBLE WALL SUMP SHALL BE PVC COATED RIGID. G: DOUBLE WALL TURBINE SUMP RISER SCALE: NTS (8-20"X 19" FLAT PANELS) _...... ---.....-- FACTORY INSTALLED 2 HP VARIABLE SPEED TURBINE W/ 3 GPH ELECTRONIC LEAK DETECTION W/ SIPHON PORT FOR VACUUM SOURCE MINI HYDROSTATIC SENSOR IN BRINE Q FACTORY SUPPLIED RESERVOIR 3" PEA GRAVEL MIN. TO PREVENT LOAD TRANSFER TO TOP OF TANK SEAL OFF W/ DRAIN 191 2 -IN -1 SENSOR BOX 217 J -BOX (TYP.) 188 2 SENSOR -NO TANK VACUUM SENSOR 1 ASSEMBLY KIT W/ MOUNTING BRACKET SEAL -OFF (TYP.) 191 1" FRP BONDED ENTRY FITTING 124 (TYP.) 1" MONITORING CONDUIT 18 (ROUTED TO INTERSTITIAL) (ROBROY THROUGH SUMP ONLY) 2" BALL VALVE 168 48" DOUBLE WALL BRINE MONITORED SUMP 2"x24" FLEX (TYP.) 175 SUMP LIQUID MONITORING SENSOR H (IN SENSOR HOLDER BELOW APEX 0 OF TANK AT LOWEST POINT) 14 148 2 INSIDE 3" FRP PRODUCT LINE TO DISPENSERS (VACUUM MONITORED) SUMP LIQUID MONITORING SENSOR 126 12 3" D.W. FRP BONDED ENTRY FITTING (IN SENSOR HOLDER BELOW APEX 22 MANWAY W/ 4x3 CONCENTRIC REDUCER W/ OF TANK AT LOWEST POINT) TEST PORT & VACUUM TUBING LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: SENSOR SHALL BE INSTALLED ON THE SAME SIDE OF PIPING PENETRATIONS AS SHOWN C: SECTION VIEW - 10K COMPARTMENT DIESEL - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" 2" CAP. DRILL HOLES IN END AN INSTALL GROMMETS FOR TUBING PASS THROUGH 16 1" MONITORING CONDUIT (ROUTED TO INTERSTITIAL) 18 (ROBROY THROUGH SUMP ONLY) �- i 1 FRP BONDED ENTRY FITTING 124 (TYP.) o J -BOX (TYP.) 188 �/ o o o/ 0 I o� o� 22" MANWAY I� a i o / 2 SENSOR -NO TANK VACUUM SENSOR ASSEMBLY KIT W/ MOUNTING BRACKET 1 �� o 2 HP VARIABLE SPEED TURBINE W/ 105 10 • 3 GPH ELECTRONIC LEAK DETECTION W/ SIPHON PORT FOR VACUUM SOURCE 109 0 LOOP VACUUM TUBING FROM PRODUCT PIPING TO VAC SENSOR 2" BELLxMALE ADAPTER (TYP.) 14 148 3" OVER 2" FIBERGLASS CROSSOVER CONTAINS VACUUM TUBING ONLY FROMFILL SUMP 2 126 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & PLUG 18 1" CONDUIT HOMERUN TO BLDG. TURBINE POWER (ROBROY THROUGH SUMP ONLY) 1241" FRP BONDED ENTRY FITTING (TYP.) 204 205 VEEDER ROOT .1 GPH MAGNOSTRICTIVE PROBE TANK LEVEL PROBE W/ TLS CAP �I & RING. OVERFILL ALARM SET © 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT I 175 2"x24" FLEX (TYP.) �I J 48" DOUBLE WALL BRINE MONITORED SUMP 14 148 2 INSIDE 3" FRP PRODUCT LINE TO DISPENSERS (VACUUM MONITORED) 3" D.W. FRP BONDED ENTRY FITTING 2 & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: THE LAST 2 FEET (MINIMUM) OF CONDUITS THAT ENTER THE DOUBLE WALL SUMP SHALL BE PVC COATED RIGID. D: PLAN VIEW - 10K COMPARTMENT DIESEL - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" *NOTE: CONTRACTOR SHALL BE HELD RESPONSIBLE FOR PROPER INSTALLATION & PREPARATION PER MANUFACTURERS INSTRUCTIONS AND SHALL REINSTALL SUMPS IF HYDROSTATIC TESTING SHOWS LEAKING IN THIS AREA OF THE SUMP. SUMPS MUST BE ORIENTED SUCH THAT THE FACE OF THE SUMP PANEL IS PARALLEL WITH ADJACENT TANK SUMP PANEL IN ORDER TO ACHIEVE THE 45° ANGLES REQUIRED TO ROUTE THE PIPING WHILE MAINTAINING THE DESIRED PERPENDICULAR ANGLE INTO THE SUMP. [� CONTRACTOR TO ADDITIONALLY GLASS WRAP & LAMINATE AT CONNECTION FOLLOWING CURING OF ADHESIVE. SPECIFIC ATTENTION MUST BE GIVEN TO SURFACE PREP AS TESTING REQUIREMENTS WILL DETECT THE SMALLEST OF FLAWS. ALL MATERIALS MUST BE COMPATIBLE WITH GASOLINE, GASOLINE WITH 15% MTBE (METHYL TERTIARY -BUTYL ETHER), OR GASOLINE WITH 10% ETOH (ETHANOL). FIBERGLASS AND RESIN MUST EXTEND 1/2" BEYOND COVERAGE OF ADHESIVE. IB HICKEN CONCRETE SLAB TO ELOW WHERE SECONDARY ONTAINMENT OF SUMP ENDS. 45" DIA. ACCESS YP.). DIMENSION REQUIRED 10 ARIES WITH FIELD CONDITIONS. SEE NOTES BELOW MANHOLE 30" I.D. 18" 1-1/2" MIN. CROWN (TYP.) (Typ• (TYP. ALL OPENINGS) 6" WIDE DETECTABLE UNDERGROUND MARKING ...°:• r :� TAPE EMPIRE MAGNATEC #31-143 (8" MIN. 12" MAX.) L00 VACUAT TUBING FROM PRODUCT PIPING TO VAC SENSOR CONTRACTOR TO INSTALL CLEVIS AND COTTER PIN 207 TANK GAUGE ADAPTER & CAP VEEDER ROOT .1 GPH MAGNOSTRICTIVE 04 205 PROBE TANK LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM SET @ 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 124 1" FRP BONDED ENTRY FITTING (TYP.) 1" HOMERUN TO BLDG. TURBINE POWER 18 (ROBROY THROUGH SUMP ONLY) 12 126 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC zNkREDUCER W/ TEST PORT & PLUG II — ao 14 148 3" OVER 2" FIBERGLASS CROSSOVER CONTAINS VACUUM TUBING ONLY FROM FILL SUMP L 2"INSIDE 3" FRP PRODUCT MANIFOLD TO 20K TANK (VACUUM MONITORED) 00 H ee3" D.W. FRP BONDED ENTRY FITTING W/ 4x3 CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: SENSOR SHALL BE INSTALLED ON THE SAME SIDE OF PIPING PENETRATIONS AS SHOWN E: SECTION VIEW - 12K COMPARTMENT PREMIUM - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" 2" CAP. DRILL HOLES IN END AN INSTALL C16GROMMETS FOR TUBING PASS THROUGH 1" MONITORING CONDUIT (ROUTED TO INTERSTITIAL) (ROBROY 18 THROUGH SUMP ONLY) 1" DOUBLE ENTRY BOOT 124 2 SENSOR -NO TANK VACUUM SENSOR ASSEMBLY KIT W/ MOUNTING BRACKET 1 2 HP VARIABLE SPEED TURBINE W/ \� • 105 10 3 GPH ELECTRONIC LEAK DETECTION W/ SIPHON PORT FOR VACUUM SOURCE 109 0 14 148 3" OVER 2" FIBERGLASS CROSSOVER CONTAINS VACUUM TUBING ONLY FROM FILL SUMP 12 126 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & PLUG 18 1" CONDUIT HOMERUN TO BLDG. TURBINE POWER (ROBROY THROUGH SUMP ONLY) 124 1" FRP BONDED ENTRY FITTING (TYP.) VEEDER ROOT .1 GPH MAGNOSTRICTIVE 204 205 PROBE TANK LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM SET © 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 175 2"x24" FLEX (TYP.) 48" DOUBLE WALL BRINE MONITORED SUMP 14 148 2 INSIDE 3" FRP PRODUCT LINE TO DISPENSERS (VACUUM MONITORED) LOOP VACUUM TUBING FROM 12612 3" D.W. FRP BONDED ENTRY FITTING PRODUCT PIPING TO VAC SENSOR & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING 2" BELLxMALE ADAPTER (TYP.) 14 LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: THE LAST 2 FEET (MINIMUM) OF CONDUITS THAT ENTER THE DOUBLE WALL SUMP SHALL BE PVC COATED RIGID. F: PLAN VIEW - 12K COMPARTMENT PREMIUM - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" FIBERGLASS PIPING, 2" NOMINAL, BONDED TO SUMP SUMP OR UDC INNER WALL USING GASOLINE COMPATIBLE EPDXY RESIN. BOTTOM OF PIPE TO BE IN CONTACT WITH LOWEST PART OF SUMP OR UDC. CONTRACTOR TO BOND UNISTRUT CHANNEL TO HOLDER TO ALLOW FIBERGLASS PIPE TO CLEAR SUMP COLLAR "LIP". CONTRACTOR TO USE GASOLINE -COMPATIBLE EPDXY TO BOND SPACER TO SUMP AND PIPE. CONTRACTOR MAY USE UNISTRUT, FIBERGLASS PIPE, OR ANY OTHER EQUIVALENT MATERIAL THAT CAN WITHSTAND ENVIRONMENT OF SUMP. 2 WIRE SHIELDED CABLE SUMP MONITOR LIQUID SENSOR INSIDE HOLDER APEX OF TANK TURBINE SIDE SUMP SENSORS TO BE MOUNTEDJ THICKEN CONCRETE SLAB TO 2 HP VARIABLE SPEED TURBINE W / 105 10 FIBERGLASS BELOW WHERE SECONDARY TANK SUMP ARE MADE AND BELOW LOWEST PENETRATION CONTAINMENT OF SUMP ENDS. 3 GPH ELECTRONIC LEAK DETECTION FIBERGLASS SUMP (TYP.). DIMENSION REQUIRED W/ SIPHON PORT FOR VACUUM SOURCE 109 0 BETWEEN SUMPS AND SIPHON PIPING PENETRATIONS 40" DIA. ACCESS 104 VARIES WITH FIELD CONDITIONS. ARE DESIGNED TO ENTER THE SAME SIDE OF THE UNISTRUT SEE NOTES BELOW MANHOLE MINI HYDROSTATIC SENSOR IN BRINT�1.- 30" I.D. 18 1-1/2" MIN. CROWN FACTORY SUPPLIED RESERVOI (TYP.) TYP. (TYP. ALL OPENINGS) CHANNEL SUMP WILL BE REQUIRED TO BE INSTALLED. 6 WIDE DETECTABLE°p :� 0 UNDERGROUND MARKING :TAPE 0 EMPIRE MAGNATEC .A : •° ;.'-3 PEA GRAVELMIN. TO a#31 CHANNEL BONDED TO 143 . ,. PREVENT LOAD TRANSFER §IRAIN io (8 MIN. 12 MAX.) TO TOP OF TANK 207 TANK GAUGE ADAPTER &CAPSEAL OFF W/ DCONTRACTOR TO INSTALL CLEVIS AND COTTER PIN 2 -IN -1 SE217 SEAL: VEEDER ROOT .1 GPH MAGNOSTRICTIVE PROBE T 04 NK J -BOX (TYP.) 188 NO. 36475 LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM ATF 0- CAUF�� 205 SET @ 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 2 SENSOR -NO TANK VACUUM LOOP VACUUM TUBING FROM 1 SENSOR ASSEMBLY KIT W/ co PRODUCT PIPING TO VAC SENSOR MOUNTING BRACKET Z 124 1" FRP BONDED ENTRY FITTING (TYP.) SEAL -OFF (TYP.) 191 0 c1) `2 1 " HOMERUN TO BLDG. TURBINE POWER 1" FRP BONDED ENTRY FITTING cc 18 (ROBROY THROUGH SUMP ONLY) (Typ.)124 IA 3" D.W. FRP BONDED ENTRY " MONITORING CONDUIT 12 126 FITTING & 4"x3" CONCENTRIC (1 ROUTED TO INTERSTITIAL 18 p Z N wz0-- REDUCER W/ TEST PORT & PLUG (ROBROY THROUGH SUMP ONLY) 06 Z.t � w 00 w 2" BALL VALVE 168 0 z 0 — 14 148 3" OVER 2" FIBERGLASS z 2 0- II CROSSOVER CONTAINS VACUUM 2"x24" FLEX (TYP.) 175 oL TUBING ONLY FROM FILL SUMP 48" DOUBLE WALL BRINE FILLE�� SITE ADDRESS: ADDRESS SUMP _r 14 148 2 INSIDE 3" FRP PRODUCT LINE TO DISPENSERS (VACUUM MONITORED) SUMP LIQUID MONITORING SENSOR 126 12 3" D.W. FRP BONDED ENTRY FITTING (IN SENSOR HOLDER BELOW APEX 22 MANWAY W/ 4x3 CONCENTRIC REDUCER W/ OF TANK AT LOWEST POINT) TEST PORT & VACUUM TUBING LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: SENSOR SHALL BE INSTALLED ON THE SAME SIDE OF PIPING PENETRATIONS AS SHOWN C: SECTION VIEW - 10K COMPARTMENT DIESEL - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" 2" CAP. DRILL HOLES IN END AN INSTALL GROMMETS FOR TUBING PASS THROUGH 16 1" MONITORING CONDUIT (ROUTED TO INTERSTITIAL) 18 (ROBROY THROUGH SUMP ONLY) �- i 1 FRP BONDED ENTRY FITTING 124 (TYP.) o J -BOX (TYP.) 188 �/ o o o/ 0 I o� o� 22" MANWAY I� a i o / 2 SENSOR -NO TANK VACUUM SENSOR ASSEMBLY KIT W/ MOUNTING BRACKET 1 �� o 2 HP VARIABLE SPEED TURBINE W/ 105 10 • 3 GPH ELECTRONIC LEAK DETECTION W/ SIPHON PORT FOR VACUUM SOURCE 109 0 LOOP VACUUM TUBING FROM PRODUCT PIPING TO VAC SENSOR 2" BELLxMALE ADAPTER (TYP.) 14 148 3" OVER 2" FIBERGLASS CROSSOVER CONTAINS VACUUM TUBING ONLY FROMFILL SUMP 2 126 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & PLUG 18 1" CONDUIT HOMERUN TO BLDG. TURBINE POWER (ROBROY THROUGH SUMP ONLY) 1241" FRP BONDED ENTRY FITTING (TYP.) 204 205 VEEDER ROOT .1 GPH MAGNOSTRICTIVE PROBE TANK LEVEL PROBE W/ TLS CAP �I & RING. OVERFILL ALARM SET © 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT I 175 2"x24" FLEX (TYP.) �I J 48" DOUBLE WALL BRINE MONITORED SUMP 14 148 2 INSIDE 3" FRP PRODUCT LINE TO DISPENSERS (VACUUM MONITORED) 3" D.W. FRP BONDED ENTRY FITTING 2 & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: THE LAST 2 FEET (MINIMUM) OF CONDUITS THAT ENTER THE DOUBLE WALL SUMP SHALL BE PVC COATED RIGID. D: PLAN VIEW - 10K COMPARTMENT DIESEL - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" *NOTE: CONTRACTOR SHALL BE HELD RESPONSIBLE FOR PROPER INSTALLATION & PREPARATION PER MANUFACTURERS INSTRUCTIONS AND SHALL REINSTALL SUMPS IF HYDROSTATIC TESTING SHOWS LEAKING IN THIS AREA OF THE SUMP. SUMPS MUST BE ORIENTED SUCH THAT THE FACE OF THE SUMP PANEL IS PARALLEL WITH ADJACENT TANK SUMP PANEL IN ORDER TO ACHIEVE THE 45° ANGLES REQUIRED TO ROUTE THE PIPING WHILE MAINTAINING THE DESIRED PERPENDICULAR ANGLE INTO THE SUMP. [� CONTRACTOR TO ADDITIONALLY GLASS WRAP & LAMINATE AT CONNECTION FOLLOWING CURING OF ADHESIVE. SPECIFIC ATTENTION MUST BE GIVEN TO SURFACE PREP AS TESTING REQUIREMENTS WILL DETECT THE SMALLEST OF FLAWS. ALL MATERIALS MUST BE COMPATIBLE WITH GASOLINE, GASOLINE WITH 15% MTBE (METHYL TERTIARY -BUTYL ETHER), OR GASOLINE WITH 10% ETOH (ETHANOL). FIBERGLASS AND RESIN MUST EXTEND 1/2" BEYOND COVERAGE OF ADHESIVE. IB HICKEN CONCRETE SLAB TO ELOW WHERE SECONDARY ONTAINMENT OF SUMP ENDS. 45" DIA. ACCESS YP.). DIMENSION REQUIRED 10 ARIES WITH FIELD CONDITIONS. SEE NOTES BELOW MANHOLE 30" I.D. 18" 1-1/2" MIN. CROWN (TYP.) (Typ• (TYP. ALL OPENINGS) 6" WIDE DETECTABLE UNDERGROUND MARKING ...°:• r :� TAPE EMPIRE MAGNATEC #31-143 (8" MIN. 12" MAX.) L00 VACUAT TUBING FROM PRODUCT PIPING TO VAC SENSOR CONTRACTOR TO INSTALL CLEVIS AND COTTER PIN 207 TANK GAUGE ADAPTER & CAP VEEDER ROOT .1 GPH MAGNOSTRICTIVE 04 205 PROBE TANK LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM SET @ 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 124 1" FRP BONDED ENTRY FITTING (TYP.) 1" HOMERUN TO BLDG. TURBINE POWER 18 (ROBROY THROUGH SUMP ONLY) 12 126 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC zNkREDUCER W/ TEST PORT & PLUG II — ao 14 148 3" OVER 2" FIBERGLASS CROSSOVER CONTAINS VACUUM TUBING ONLY FROM FILL SUMP L 2"INSIDE 3" FRP PRODUCT MANIFOLD TO 20K TANK (VACUUM MONITORED) 00 H ee3" D.W. FRP BONDED ENTRY FITTING W/ 4x3 CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: SENSOR SHALL BE INSTALLED ON THE SAME SIDE OF PIPING PENETRATIONS AS SHOWN E: SECTION VIEW - 12K COMPARTMENT PREMIUM - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" 2" CAP. DRILL HOLES IN END AN INSTALL C16GROMMETS FOR TUBING PASS THROUGH 1" MONITORING CONDUIT (ROUTED TO INTERSTITIAL) (ROBROY 18 THROUGH SUMP ONLY) 1" DOUBLE ENTRY BOOT 124 2 SENSOR -NO TANK VACUUM SENSOR ASSEMBLY KIT W/ MOUNTING BRACKET 1 2 HP VARIABLE SPEED TURBINE W/ \� • 105 10 3 GPH ELECTRONIC LEAK DETECTION W/ SIPHON PORT FOR VACUUM SOURCE 109 0 14 148 3" OVER 2" FIBERGLASS CROSSOVER CONTAINS VACUUM TUBING ONLY FROM FILL SUMP 12 126 3" D.W. FRP BONDED ENTRY FITTING & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & PLUG 18 1" CONDUIT HOMERUN TO BLDG. TURBINE POWER (ROBROY THROUGH SUMP ONLY) 124 1" FRP BONDED ENTRY FITTING (TYP.) VEEDER ROOT .1 GPH MAGNOSTRICTIVE 204 205 PROBE TANK LEVEL PROBE W/ TLS CAP & RING. OVERFILL ALARM SET © 90% CAPACITY. USE 4" FLOAT IN INSTALL KIT 175 2"x24" FLEX (TYP.) 48" DOUBLE WALL BRINE MONITORED SUMP 14 148 2 INSIDE 3" FRP PRODUCT LINE TO DISPENSERS (VACUUM MONITORED) LOOP VACUUM TUBING FROM 12612 3" D.W. FRP BONDED ENTRY FITTING PRODUCT PIPING TO VAC SENSOR & 4"x3" CONCENTRIC REDUCER W/ TEST PORT & VACUUM TUBING 2" BELLxMALE ADAPTER (TYP.) 14 LOOPED TO VAC SENSOR ASSEMBLY (TYP.) NOTE: THE LAST 2 FEET (MINIMUM) OF CONDUITS THAT ENTER THE DOUBLE WALL SUMP SHALL BE PVC COATED RIGID. F: PLAN VIEW - 12K COMPARTMENT PREMIUM - ONE PUMP, ONE LINE SCALE: 3/4" = 1'-0" FIBERGLASS PIPING, 2" NOMINAL, BONDED TO SUMP SUMP OR UDC INNER WALL USING GASOLINE COMPATIBLE EPDXY RESIN. BOTTOM OF PIPE TO BE IN CONTACT WITH LOWEST PART OF SUMP OR UDC. CONTRACTOR TO BOND UNISTRUT CHANNEL TO HOLDER TO ALLOW FIBERGLASS PIPE TO CLEAR SUMP COLLAR "LIP". CONTRACTOR TO USE GASOLINE -COMPATIBLE EPDXY TO BOND SPACER TO SUMP AND PIPE. CONTRACTOR MAY USE UNISTRUT, FIBERGLASS PIPE, OR ANY OTHER EQUIVALENT MATERIAL THAT CAN WITHSTAND ENVIRONMENT OF SUMP. 2 WIRE SHIELDED CABLE SUMP MONITOR LIQUID SENSOR INSIDE HOLDER APEX OF TANK TURBINE SIDE SUMP SENSORS TO BE MOUNTEDJ I BELOW APEX OF TANK, AT BOTTOM OF SUMP AT FIBERGLASS SIDE OF TANK WHERE PRODUCT PENETRATIONS INTO TANK SUMP ARE MADE AND BELOW LOWEST PENETRATION DATE FITTING WITHIN SUMP AREA. PRODUCT PIPING TO FIBERGLASS SUMP DISPENSERS, PRODUCT PIPING CROSS CONNECTION INSIDE TANK COLLAR BETWEEN SUMPS AND SIPHON PIPING PENETRATIONS LIP ARE DESIGNED TO ENTER THE SAME SIDE OF THE UNISTRUT 1. SENSOR HOLDER SUMP AS SHOWN. IF PRODUCT PENETRATION CHANNEL BONDED TO UNISTRUT ENTERS ON BOTH SIDES OF SUMP DUE TO FIELD CONDITIONS, THEN DUAL SENSORS AT TURBINE CHANNEL SUMP WILL BE REQUIRED TO BE INSTALLED. 0 2. SENSOR HOLDER 0 AND UNISTRUT CHANNEL BONDED TO SUMP WALL. DO NOT io PENETRATE SUMP! H: SUMP SENSOR HOLDER DETAILS SCALE: 1" = 1'-0" NOTE: CONTRACTOR TO USE ADDITIONAL GALVANIZED FITTINGS AS REQUIRED TO MINIMIZE BENDS IN FLEXIBLE CONNECTORS NOTE: INDICATES ITEMS FOUND ON XX MATERIALS LIST SHEETS M.5.3.01 & M.5.3.02 CLIENT: 4: bp 'Ad & lir ARCO BP WEST COAST PRODUCTS, LLC NO. DATE DESCRIPTION 0 0 0 0 0 0 0 io SEAL: FESS /0 Of-�gp�l NO. 36475 * XP. 6-30-22 ATF 0- CAUF�� z Lu w .Q co Uzoo 0 Z z~�� � 0 c1) `2 mZ 0 c)dc, =) Q U cc Qw I I w w c/'z}LL 0 O z o co zUUo zz Q p Z N wz0-- �LU wQ}Z� z Q -- 06 Z.t � w 00 w Q 0 z 0 z 2 0- z g oL DEVELOPMENT INFORMATION: SITE ADDRESS: ADDRESS 2510 S. STATE HWY 99 W. FRONTAGE ROAD SAN JOAQUIN COUNTY, CA 95205 DESIGNED BY: CHECKED BY: DRAWN BY: ER DATE: PROJECT NO: 10/24/2019 DRAWING TITLE: TURBINE SIDE SUMPS AND PIPING INSTALLATION DETAILS (SINGLE 2HP TURBINE, 2022 CONFIGURATION D.W. VENT/VAPOR) SHEET NO: M,5,3,13