INSTALL_2022 - Laserfiche WebLink

Home Browse Search

K- 190OW-2 Hot Line Wall Phone To install the K-1900W-2 line up the pins of the RJ11 W Jack with the slots RJ11 W on the back of the phone, insert and press down as shown to the right. (not Included) _W_ Dimensions: 102mm x 121 mm x 229mm (4.0"x 4.75"x 9.0") E Shipping Weight: 1.36 Kg (3 lbs) ® -or- Connections: RJ11W —� Colors: Red or Ash K-190OW-2 P C.O.Line or Analog w 031 Optional VE-9x12 Weatherproof Housing for the K-1900W-2, available PABXIKSU Extension N in emergency red or safety yellow. For more information on the VE- optional VE-9x12 »E 9x12, see DOD#413. DOD#413 (not included) K- 1900-6 Hot Line Dialer Network The K-1900-6 Hot-Lino Dialer Network can be used K-1900-6 PGB with Standard Network with any carbon microphone handset and a SPDT Mounting Bracket(included) Pole Double Throw hook switch or typical C.A.Line 0.55" (Single ) Yp or Analog 500, 554, 2500 and 2554 phones. Attach wires as PABXIKSU 0.47 mF@250V Opll...I Ring., shown to the right. An electronic ringer may be used Extension (Induces ��„nu"ded) ._ .pndnde.r If Inbound call capability is required. °reB" r ...... .Q........... �............ ° .. ... '} o M Ott Required Handset Type: Carbon microphone SPDT Rqa R �IS�II{I ° 0 elateferown ISI• 3.05” Required Hookswitch: Single pole double throw Hookswitch s� I Io Dimensions: 88.9mm x 68.6mm x 33mm(3.5"x 2.7"x 1.3") (shown on 51e10 Ycll.w si u �8 white ur stae5hippfn Weight: 0.45 Kg 1.0 lb) hook) RX2 T d Green Connections: Miniature spade receptaclesH.c. RXI oo wn,,. Compatible Phones: 500,554,2500 and 2554 ............. ' 61ack sx1 11 LJ CHa dgote Note: If the phone has a ringer, the Included capacitor MUST be installed as shown. Txs Red (not ilnG"ded) (2)Od36"Mamie, .. M—nlln0 H.les.................. ...f Programming While in the programming mode, two beeps indicate a valid programming entry.An invalid entry will be indicated with three beeps. To exit programming, simply hang-up the K-1900 Series phone. A. Accessing the Programming Mode 1. Using the Security Code Step 1. Connect the K-1900 Series device to an analog C.O, line, or an analog PABXIKSU station. Step 2. From a Touch Tone phone, call into the K-1900 Series phone. Step 3. Listen for at least one ringback In the calling phone and then take the K-1900 Series phone off-hook(answer the phone). Step 4. From the Touch Tone phone, enter your six digit security code(factory set to 845464-see section E). Step 5. A double beep Indicates the K-1900 Series phone is in the programming mode(see sections B-G ). If six digits are entered and no beeps are heard,an incorrect security code has been entered. Repeat steps 2-5 or follow directions in 2.Without a Security Code below. 2. Without a Security Code (if You Have Forgotten or lost the Security Code) 1.33'r •� ,(2)0.156"Die. �(�----- Step 1. Remove JP1 (as shown to the right). For the K-190OW-2 and K-1900D-2, the Mounting Holes rvl plastic cover must be removed to expose the circuit board. 1:1 UD 94 JLJ r-, Step 2. Connect the K-1900 Series device to a C.O. line, analog PABXIKSU station or 'DOQ p to a DLE-200B Line Simulator. �oB """"'Jp1 Step 3. 1 From a Touch Tone phone, call into the K-1900 Series phone. Step 4. Listen for at least one ringback In the calling phone and then take the KA900 €4 Q Cd z.z3" Series phone off-hook(answer the phone). U Step 5. A double beep indicates the K-1900 Series phone Is in the programming mode M O (see Programming sections B-G). Step 6. When programming is finished, replace JP1 and replace cover on phone. Note: JP1 MUST be In place for normal operation.